Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION UNIT
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297553 AUTOMATIC TRANSMISSION UNIT A

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C259598E01
0.841,0.443 0.965,0.603 0.124,0.161 10 A 1.965,0.04 2.089,0.200 0.124,0.161 10 B 1.414,2.781 1.538,2.942 0.124,0.161 10 C 3.642,2.081 3.766,2.241 0.124,0.161 10 D 4.94,1.637 5.064,1.798 0.124,0.161 10 E 5.613,2.987 5.737,3.147 0.124,0.161 10 F 6.897,4.07 7.021,4.231 0.124,0.161 10 H 4.599,4.612 4.756,4.772 0.156,0.161 10 G 6.878,5.555 7.002,5.716 0.124,0.161 10 K 4.006,7.853 4.130,8.013 0.124,0.161 10 J 1.919,6.907 2.042,7.068 0.124,0.161 10 I

Mark Front Race Diameter
Inside / Outside
Thrust Bearing Diameter
Inside / Outside
Rear Race Diameter
Inside / Outside
A 74.2 mm (2.921 in.) / 87.7 mm (3.453 in.) 71.9 mm (2.831 in.) / 85.6 mm (3.370 in.) -
B 37.0 mm (1.457 in.) / 51.2 mm (2.016 in.) 33.5 mm (1.319 in.) / 48.0 mm (1.890 in.) -
C 20.0 mm (0.787 in.) / 35.6 mm (1.402 in.) 20.0 mm (0.787 in.) / 41.0 mm (1.614 in.) -
D 31.0 mm (1.220 in.) / 48.0 mm (1.890 in.) 33.3 mm (1.311 in.) / 51.2 mm (2.016 in.) -
E - 42.5 mm (1.673 in.) / 61.2 mm (2.409 in.) -
F 34.9 mm (1.374 in.) / 50.8 mm (1.999 in.) 38.6 mm (1.520 in.) / 53.1 mm (2.091 in.) -
G - 58.5 mm (2.303 in.) / 73.5 mm (2.894 in.) 55.2 mm (2.173 in.) / 71.2 mm (2.803 in.)
H 29.6 mm (1.165 in.) / 44.9 mm (1.768 in.) 27.8 mm (1.095 in.) / 43.8 mm (1.726 in.) 27.8 mm (1.095 in.) / 43.7 mm (1.721 in.)
I 19.0 mm (0.748 in.) / 35.0 mm (1.378 in.) 20.8 mm (0.819 in.) / 38.5 mm (1.516 in.) -
J 43.3 mm (1.705 in.) / 56.7 mm (2.232 in.) 40.6 mm (1.598 in.) / 58.0 mm (2.284 in.) -
K 37.0 mm (1.457 in.) / 51.2 mm (2.016 in.) 36.1 mm (1.421 in.) / 52.5 mm (2.067 in.) 36.1 mm (1.421 in.) / 51.0 mm (2.007 in.)

Hide 35629A 2.INSTALL NO. 4 BRAKE PISTON

a.
C109328E08
0.729,0.615 0.479,0.427 false 2.01,0.354 1.76,0.167 false 0.813,1.208 1.792,1.635 1.792,1.635 1.604,1.292 true 2.156,0.823 2.75,0.323 2.75,0.323 2.677,0.76 true 2.75,0.167 2.927,0.365 0.177,0.198 10 false *3 1.844,1.552 2.021,1.75 0.177,0.198 10 false *3 0.313,0.313 0.49,0.51 0.177,0.198 10 false *1 1.604,0.042 1.781,0.24 0.177,0.198 10 false *2

Coat 2 new O-ring with ATF, and install them to the brake reaction sleeve.

Text in Illustration
*1 Brake Reaction Sleeve
*2 No. 4 Brake Piston
*3 O-ring


b.

Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.


c.

Install the No. 4 brake piston to the brake reaction sleeve.

NOTICE:

Be careful not to damage the O-rings.



Hide 35626 3.INSTALL BRAKE REACTION SLEEVE

a.
C108604E05
2.336,0.19 2.597,0.392 0.261,0.201 10 *2 2.29,0.28 2.17,0.28 2.17,0.28 2.17,1.569 false 1.265,0.274 1.127,0.274 1.127,0.274 1.127,1.426 false 1.302,0.19 1.563,0.392 0.261,0.201 10 *1

With the No. 4 brake piston underneath (the rear side), install the brake reaction sleeve and the No. 4 brake piston to the automatic transmission case sub-assembly.

Text in Illustration
*1 Brake Reaction Sleeve
*2 No. 4 Brake Piston

NOTICE:

Be careful not to damage the O-rings.



Hide 35623H 4.INSTALL 1ST AND REVERSE BRAKE PISTON

a.
C108605E02
1.251,0.39 1.496,0.602 0.246,0.212 10 *1 1.027,1.282 1.027,0.492 1.027,0.492 1.233,0.492 false

Coat a new O-rings with ATF, and install it to the 1st and reverse brake piston.

Text in Illustration
*1 1st and Reverse Brake Piston


b.

With the spring seat of the 1st and reverse brake piston facing upwards (the front side), place the 1st and reverse brake piston in the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



Hide 35068 5.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.

Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.


b.
C108601E03
0.686,0.039 1.072,0.333 0.386,0.293 10 SST 2.267,0.027 2.423,0.224 0.157,0.197 10 *1 2.244,0.125 2.124,0.125 2.124,0.125 2.124,1.105 false 1.065,0.159 1.173,0.159 1.173,0.159 1.173,0.744 false

Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.

Text in Illustration
*1 Snap Ring

SST
09350-30020  (09350-07050)


c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 35666 6.INSTALL BRAKE APPLY TUBE

a.
C108600

Install the brake apply tube with its protruding part fitting into the groove of the automatic transmission case sub-assembly as shown in the illustration.

NOTICE:

Engage the 1st and reverse brake piston claw with the protrusion of the brake apply tube.



Hide 35760 7.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
D027947

Install the thrust needle roller bearing to the automatic transmission case sub-assembly.

Bearing Diameter
Item Inside Outside
Thrust needle roller bearing 40.6 mm (1.598 in.) 58.0 mm (2.284 in.)


b.
C109347E07
3.135,0.833 3.135,1.229 false 0.677,0.24 0.563,0.24 0.563,0.24 0.563,1.219 false 0.323,1.667 0.323,1.844 0.323,1.844 0.875,1.844 false 0.896,1.719 1.052,1.896 0.156,0.177 10 false *1 3.063,1.24 3.24,1.438 0.177,0.198 10 false *3 0.708,0.135 0.896,0.333 0.188,0.198 10 false *2

Install the thrust needle roller bearing to the rear planetary gear assembly.

Text in Illustration
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 No. 9 Thrust Bearing Race

Bearing and Race Diameter
Item Inside Outside
Thrust needle roller bearing 20.8 mm (0.819 in.) 38.5 mm (1.516 in.)
Thrust bearing race 19.0 mm (0.748 in.) 35.0 mm (1.378 in.)
No. 9 thrust bearing race 43.3 mm (1.705 in.) 56.7 mm (2.232 in.)


c.

Coat the No. 9 thrust bearing race and the thrust bearing race with petroleum jelly, and install them onto the rear planetary gear assembly.


d.
C109346

Install the rear planetary gear assembly to the automatic transmission case sub-assembly.


Hide 35684 9.INSTALL NO. 4 BRAKE DISC

a.
C230499E03
0.521,0.177 0.229,0.177 false 1.49,1.75 1.229,1.75 false 1.469,0.354 1.219,0.354 false 0.542,0.51 0.229,0.51 false 1.229,1.521 1.365,1.521 1.365,1.521 1.365,0.354 false 1.229,1.229 1.365,1.229 false 1.219,0.948 1.354,0.948 false 1.229,0.656 1.365,0.656 false 0.365,0.51 0.365,1.406 0.365,1.406 0.521,1.406 false 0.521,0.844 0.365,0.844 false 0.521,1.125 0.365,1.125 false 1.5,1.667 1.656,1.844 0.156,0.177 10 false *1 0.063,0.104 0.219,0.281 0.156,0.177 10 false *1 0.052,0.427 0.208,0.604 0.156,0.177 10 false *3 1.521,0.25 1.677,0.427 0.156,0.177 10 false *2

Install the 2 No. 4 brake flanges, 5 No. 4 brake discs and the 4 No. 4 brake plates to the automatic transmission case sub-assembly.

Text in Illustration
*1 No. 4 Brake Flange
*2 No. 4 Brake Disc
*3 No. 4 Brake Plate

Installation order:

*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


NOTICE:

Make sure that the discs, plates and the flanges are installed in the correct order.



Hide 35639B 10.INSTALL BRAKE PLATE STOPPER SPRING

a.
D027943

Install the brake plate stopper spring to the automatic transmission case sub-assembly.


Hide 35077D 11.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

a.
C108607E10
1.667,1.208 1.938,1.208 false 1.375,1.323 1.375,1.792 false 1.094,1.146 1.094,0.25 1.094,0.25 1.198,0.25 false 0.375,1.063 0.375,0.531 0.375,0.531 0.5,0.531 false 0.531,0.448 0.74,0.646 0.208,0.198 10 false *1 1.229,0.146 1.438,0.344 0.208,0.198 10 false *2 1.281,1.792 1.49,1.99 0.208,0.198 10 false *3 1.958,1.135 2.167,1.333 0.208,0.198 10 false *4

Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and the rear planetary ring gear flange sub-assembly to the intermediate shaft.

Text in Illustration
*1 Rear Planetary Ring Gear Flange Sub-assembly
*2 No. 7 Thrust Bearing Race
*3 Thrust Needle Roller Bearing
*4 No. 8 Thrust Bearing Race

Bearing and Race Diameter
Item Inside Outside
No. 7 thrust bearing race 29.6 mm (1.165 in.) 44.9 mm (1.768 in.)
Thrust needle roller bearing 27.8 mm (1.095 in.) 43.8 mm (1.726 in.)
No. 8 thrust bearing race 27.8 mm (1.095 in.) 43.7 mm (1.721 in.)


Hide 35770C 12.INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY

a.
D027964E11
0.927,0.76 0.75,0.542 0.75,0.542 0.604,0.542 false 0.375,1.625 0.531,1.917 0.531,1.917 0.667,1.917 false 0.406,0.448 0.563,0.625 0.156,0.177 10 false *1 0.698,1.823 0.854,2 0.156,0.177 10 false *2

Install the No. 3 one-way clutch assembly and the one-way clutch inner race to the intermediate shaft.

Text in Illustration
*1 No. 3 One-way Clutch Assembly
*2 One-way Clutch Inner Race


Hide 35713 13.INSTALL INTERMEDIATE SHAFT

a.
D031411

Install the intermediate shaft together with the No. 3 one-way clutch assembly to the automatic transmission case sub-assembly.


b.
D031365E07
2.396,0.333 2.75,0.333 false 2.802,0.219 3.125,0.417 0.323,0.198 10 false SST

Using SST, install the snap ring to the automatic transmission case sub-assembly.

SST
09350-30020  (09350-07060)


Hide 35750 14.INSTALL CENTER PLANETARY GEAR ASSEMBLY

a.
C256936E01
0.097,0.265 0.267,0.425 0.170,0.161 10 *1 0.28,0.35 0.49,0.35 false 0.097,0.661 0.267,0.822 0.170,0.161 10 *2 0.28,0.746 0.49,0.746 false 0.097,1.168 0.267,1.329 0.170,0.161 10 *3 0.28,1.253 0.421,1.253 false 0.097,1.689 0.267,1.850 0.170,0.161 10 *4 0.28,1.774 0.573,1.774 false

Install the center planetary gear assembly and the planetary sun gear to the automatic transmission case sub-assembly.

Text in Illustration
*1 Thrust Needle Roller Bearing
*2 No. 4 Thrust Bearing Race
*3 Center Planetary Gear Assembly
*4 Planetary Sun Gear

Bearing and Race Diameter
Item Inside Outside
Thrust needle roller bearing 58.5 mm (2.303 in.) 73.5 mm (2.894 in.)
No. 4 thrust bearing race 55.2 mm (2.173 in.) 71.2 mm (2.803 in.)


b.

Coat the No. 4 thrust bearing race with petroleum jelly, and install it onto the center planetary gear assembly.


c.

Install the thrust needle roller bearing to the center planetary gear assembly.


Hide 35622G 15.INSTALL NO. 2 BRAKE PISTON

a.
D028797E22
0.865,1.802 1.75,1.802 1.75,1.802 1.51,1.594 true 1.781,1.719 1.99,1.958 0.208,0.24 10 false *1

Coat 2 new O-rings with ATF, and install them to the No. 2 brake piston.

Text in Illustration
*1 O-ring


b.

Press the No. 2 brake piston into the No. 2 brake cylinder.

NOTICE:

Be careful not to damage the O-rings.



c.

Install the No. 2 brake piston to the automatic transmission case sub-assembly.

HINT:

Install the No. 2 brake cylinder so that the projection protrudes from the upside of the automatic transmission case sub-assembly.



d.
D031529

Check that the oil pressure apply hole of the No. 2 brake cylinder aligns with the oil pressure apply hole of the automatic transmission case sub-assembly.


Hide 35682A 16.INSTALL NO. 2 BRAKE DISC

a.
C231583E01
1.22,0 1.376,0.181 0.156,0.181 10 *a

Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly as shown in the illustration.

Text in Illustration
*a Identification shape

NOTICE:

Make sure that the identification shape of the No. 2 brake piston return spring sub-assembly faces the upper right side as shown in the illustration.



b.
C231118E04
0.51,0.375 0.333,0.375 false 1.219,0.521 1.292,0.521 1.292,0.521 1.292,1.417 false 0.521,0.688 0.427,0.688 0.427,0.688 0.427,1.25 false 1.292,0.823 1.219,0.823 false 0.521,0.969 0.427,0.969 false 1.292,1.115 1.219,1.115 false 0.521,1.25 0.333,1.25 false 1.344,1.417 1.219,1.417 false 0.521,1.542 0.333,1.542 false 0.167,0.292 0.333,0.448 0.167,0.156 10 false *1 0.167,1.458 0.333,1.615 0.167,0.156 10 false *1 0.167,1.167 0.333,1.323 0.167,0.156 10 false *3 1.354,1.313 1.521,1.469 0.167,0.156 10 true *2

Install the 2 No. 2 brake flanges, 4 No. 2 brake discs and the 3 No. 2 brake plates to the automatic transmission case sub-assembly.

Text in Illustration
*1 No. 2 Brake Flange
*2 No. 2 Brake Disc
*3 No. 2 Brake Plate

Installation order:

*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


NOTICE:

Make sure that the discs, plates and the flanges are installed in the correct order.



c.
C256935E04
0.51,1.875 1.333,1.396 true 1.375,1.51 1.333,1.531 false 1.375,1.417 1.333,1.448 false 1.385,1.333 1.344,1.354 false 1.385,1.229 1.344,1.26 false 2.385,0.469 2.635,1.375 2.635,1.375 1.865,1.031 true 2.604,1.385 2.938,1.573 0.333,0.188 10 false SST 0.323,1.802 0.5,1.99 0.177,0.188 10 false *1

Using SST and a screwdriver, compress the No. 2 brake piston return spring sub-assembly and install the snap ring to the automatic transmission case sub-assembly.

Text in Illustration
*1 Protective Tape

SST
09350-30020  (09350-07020)
09380-60010  (09381-06030, 09381-06050, 09381-06080, 09381-06090, 09381-06100, 09381-06110)

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35621V 18.INSTALL NO. 1 BRAKE PISTON

a.
D028539E20
1.031,1.146 0.573,1.5 true 1.698,1.5 0.583,1.5 true 0.385,1.406 0.573,1.604 0.188,0.198 10 false *1

Coat 2 new O-rings with ATF, and install them to the No. 1 brake piston.

Text in Illustration
*1 O-ring


b.

Press the No. 1 brake piston into the No. 1 brake cylinder.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608J 19.INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
D027935E14
1.427,0.323 1.188,0.167 1.188,0.167 1.031,0.167 false 1.438,1.042 1.104,1.042 false 0.865,0.073 1.021,0.25 0.156,0.177 10 false *1 0.917,0.948 1.073,1.125 0.156,0.177 10 false *2

Install the brake piston return spring sub-assembly and the No. 1 brake cylinder to the automatic transmission case sub-assembly.

Text in Illustration
*1 Brake Piston Return Spring Sub-assembly
*2 No. 1 Brake Cylinder

HINT:

Install the No. 1 brake cylinder so that the projection protrudes from the upside of the automatic transmission case sub-assembly.



b.
D031528

Check that the oil pressure apply hole of the No. 1 brake cylinder aligns with the oil pressure apply hole of the automatic transmission case sub-assembly.


c.
C256934E04
1.365,1.5 1.333,1.521 false 1.365,1.427 1.323,1.448 false 1.375,1.333 1.333,1.365 false 1.375,1.219 1.333,1.25 false 0.5,1.875 1.323,1.396 true 2.344,0.479 2.625,1.385 true 1.833,1.052 2.625,1.385 true 2.667,1.375 3,1.563 0.333,0.188 10 false SST 0.313,1.792 0.49,1.979 0.177,0.188 10 false *1

Using SST and a screwdriver, compress the brake piston return spring sub-assembly and install the snap ring to the automatic transmission case sub-assembly.

Text in Illustration
*1 Protective Tape

SST
09350-30020  (09350-07020)
09351-40010  (09351-04010, 09351-04020)

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35763 20.INSTALL CENTER PLANETARY RING GEAR

a.
C230648E02
1.156,1.281 1,1.5 1,1.5 1,1.604 false 0.927,1.635 1.094,1.802 0.167,0.167 10 false *1

Install the front planetary ring gear flange sub-assembly to the center planetary ring gear.

Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the center planetary ring gear.


HINT:

Tape the screwdriver tip before use.



c.

Install the center planetary ring gear to the front planetary ring gear.


d.
C230652E01
1.749,0.676 1.749,0.128 1.749,0.128 1.543,0.128 false 1.365,0.042 1.521,0.196 0.156,0.154 10 *1

Using a screwdriver, install the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Be careful not to damage the front planetary ring gear.

·

Install the snap ring to the front planetary ring gear so that both ends of the snap ring come to the center of a protrusion on the front planetary ring gear.



HINT:

Tape the screwdriver tip before use.



Hide 35743 21.INSTALL FRONT PLANETARY RING GEAR

a.
C108586

Install the front planetary ring gear to the automatic transmission case sub-assembly.


Hide 35720 22.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
D027931E32
0.302,0.271 0.188,0.271 false 0.292,0.958 0.188,0.958 false 0.396,1.469 0.302,1.323 0.302,1.323 0.188,1.323 false 0.021,0.865 0.188,1.073 0.167,0.208 10 false *2 0.031,0.167 0.188,0.375 0.156,0.208 10 false *1 0.031,1.24 0.188,1.448 0.156,0.208 10 false *3

Install the No. 2 planetary carrier thrust washer and the front planetary flange thrust needle roller bearing.

Text in Illustration
*1 Front Planetary Flange Rear Thrust Bearing Race
*2 Front Planetary Flange Thrust Needle Roller Bearing
*3 No. 2 Planetary Carrier Thrust Washer

Bearing and Race Diameter
Item Inside Outside
Front planetary flange thrust needle roller bearing 38.6 mm (1.520 in.) 53.1 mm (2.091 in.)
Front planetary flange rear thrust bearing race 34.9 mm (1.374 in.) 50.8 mm (1.999 in.)


b.

Coat the front planetary flange rear thrust bearing race with petroleum jelly, and install it onto the front planetary ring gear.


c.
D027930E13
2.302,0.385 2.927,0.385 false 2.271,1 2.938,1 false 2.958,0.302 3.115,0.479 0.156,0.177 10 false *1 2.958,0.906 3.115,1.083 0.156,0.177 10 false *2

Install the front planetary gear assembly and the one-way clutch inner race sub-assembly to the automatic transmission case sub-assembly.

Text in Illustration
*1 One-way Clutch Inner Race Sub-assembly
*2 Front Planetary Gear Assembly


Hide 35681A 24.INSTALL NO. 1 BRAKE DISC

a.
C230500E05
0.479,0.281 0.24,0.281 false 1.479,0.531 1.24,0.531 false 0.49,1.635 0.24,1.635 false 1.25,1.438 1.375,1.438 1.375,1.438 1.375,0.542 false 1.24,0.979 1.365,0.979 false 0.5,0.781 0.323,0.781 0.323,0.781 0.323,1.625 false 0.49,1.219 0.333,1.219 false 0.052,1.552 0.208,1.729 0.156,0.177 10 false *1 1.49,0.438 1.646,0.615 0.156,0.177 10 false *2 0.073,0.198 0.229,0.375 0.156,0.177 10 false *3

Install the No. 1 brake flange, 3 No. 1 brake discs and the 3 No. 1 brake plates to the automatic transmission case sub-assembly.

Text in Illustration
*1 No. 1 Brake Plate
*2 No. 1 Brake Disc
*3 No. 1 Brake Flange

Installation order:

*1 - *2 - *1 - *2 - *1 - *2 - *3


NOTICE:

Make sure that the discs, plates and the flange are installed in the correct order.



Hide 35790 25.INSTALL ONE-WAY CLUTCH ASSEMBLY

a.
D027928E10
2.219,1.094 2.802,1.094 false 2.344,0.344 2.802,0.344 false 2.844,0.26 3,0.438 0.156,0.177 10 false *1 2.844,1.01 3,1.188 0.156,0.177 10 false *2

Install the No. 1 planetary carrier thrust washer and the one-way clutch assembly to the automatic transmission case sub-assembly.

Text in Illustration
*1 One-way Clutch Assembly
*2 No. 1 Planetary Carrier Thrust Washer


Hide 35624 26.INSTALL 2ND BRAKE PISTON

a.
D028546E27
0.844,1.74 1.906,1.74 false 1.427,1.396 1.906,1.74 false 1.948,1.625 2.125,1.823 0.177,0.198 10 false *1

Coat 2 new O-rings with ATF, and install them to the 2nd brake piston.

Text in Illustration
*1 O-ring


b.

Press the 2nd brake piston into the 2nd brake cylinder.

NOTICE:

Be careful not to damage the O-rings.



c.
C256937E02
0.562,0.326 0.732,0.487 0.170,0.161 10 *1 1.167,0.406 0.743,0.406 false 0.562,0.896 0.732,1.056 0.170,0.161 10 *2 1.167,0.976 0.743,0.976 false 0.562,1.465 0.732,1.626 0.170,0.161 10 *3 1.076,1.545 0.743,1.545 false

Using a screwdriver, install the No. 3 brake piston return spring sub-assembly to the 2nd brake cylinder with the snap ring.

Text in Illustration
*1 Snap Ring
*2 No. 3 Brake Piston Return Spring Sub-assembly
*3 2nd Brake Cylinder

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Be careful not to damage the 2nd brake cylinder.



HINT:

Tape the screwdriver tip before use.



Hide 35664 27.INSTALL 2ND BRAKE CYLINDER

a.
C108608

Install the 2nd brake cylinder to the automatic transmission case sub-assembly.


b.
D031530

Check that the oil pressure apply hole of the 2nd brake cylinder aligns with the oil pressure apply hole of the automatic transmission case sub-assembly.


c.
U147222E05
2.188,0.427 2.427,0.427 false 2.458,0.333 2.792,0.531 0.333,0.198 10 false SST

Using SST, install the snap ring to the automatic transmission case sub-assembly.

SST
09350-30020  (09350-07060)


Hide 35066 28.INSTALL NO. 3 BRAKE DISC (2ND BRAKE DISC SET)

a.
C122833E05
0.24,1.583 0.375,1.583 false 0.24,0.552 0.375,0.552 false 0.302,1.271 0.375,1.271 false 0.375,0.979 0.302,0.979 0.302,0.979 0.302,1.583 false 1.271,1.396 1.146,1.396 true 1.229,1.083 1.125,1.083 true 1.135,0.76 1.219,0.76 1.219,0.76 1.219,1.385 true 0.063,1.5 0.229,1.656 0.167,0.156 10 false *1 0.063,0.458 0.229,0.615 0.167,0.156 10 false *3 1.271,1.313 1.438,1.469 0.167,0.156 10 true *2

Install the No. 3 brake flange, 3 No. 3 brake discs and the 3 No. 3 brake plates to the automatic transmission case sub-assembly.

Text in Illustration
*1 No. 3 Brake Plate
*2 No. 3 Brake Disc
*3 No. 3 Brake Flange

Installation order:

*1 - *2 - *1 - *2 - *1 - *2 - *3


NOTICE:

Make sure that the discs, plates and the flange are installed in the correct order.



b.
C230646E06
1.948,0.875 2.771,0.406 2.771,0.406 2.99,0.406 false 3.01,0.313 3.167,0.479 0.156,0.167 10 false *1

Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the automatic transmission case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35606A 29.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
D028816E16
2.073,1.333 2.302,1.74 2.302,1.74 2.552,1.302 false 2.198,1.771 2.385,1.969 0.188,0.198 10 false *1

Coat 2 new O-rings with ATF, and install them to the direct clutch piston sub-assembly.

Text in Illustration
*1 O-ring


b.
C261813E01
0.438,1.149 0.608,1.310 0.170,0.161 10 *1 0.929,1.236 0.624,1.236 false

Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.

Text in Illustration
*1 O-ring


c.
D028517E12
2.313,0.292 2.125,0.115 2.125,0.115 1.99,0.115 false 1.448,0.646 1.26,0.469 1.26,0.469 1.125,0.469 false 0.531,0.865 0.354,0.688 0.354,0.688 0.219,0.688 false 1.813,0.021 1.969,0.198 0.156,0.177 10 false *1 0.938,0.385 1.094,0.563 0.156,0.177 10 false *2 0.052,0.604 0.208,0.781 0.156,0.177 10 false *3

Install the No. 2 clutch balancer and the direct clutch return spring sub-assembly to the direct clutch piston sub-assembly.

Text in Illustration
*1 Direct Clutch Piston Sub-assembly
*2 Direct Clutch Return Spring Sub-assembly
*3 No. 2 Clutch Balancer


d.

Press the direct clutch piston sub-assembly into the reverse clutch drum sub-assembly by hands.

NOTICE:

Be careful not to damage the O-rings.



e.
C369169E01
2.396,1.302 2.531,1.938 2.531,1.938 1.76,1.271 true 2.438,1.958 2.896,2.156 0.458,0.198 10 false SST

Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.

SST
09320-89010  

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



f.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




g.
D028536E26
1.188,1.01 1.708,1.5 false 1.698,1.5 2.177,1.042 false 1.646,1.51 1.844,1.719 0.198,0.208 10 false *1

Set the end gap of the snap ring in the No. 2 clutch balancer as shown in the illustration.

Text in Illustration
*1 Stopper


Hide 35048 30.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

a.
D028513E16
1.188,1.792 1.365,1.854 false 1.406,1.802 1.604,2.01 0.198,0.208 10 false *1

Coat a new O-ring with ATF, and install it to the reverse clutch drum sub-assembly.

Text in Illustration
*1 O-ring


b.
D028512E16
2.219,0.344 1.75,0.208 false 1.521,0.115 1.719,0.344 0.198,0.229 10 false *1

Coat a new O-ring with ATF, and install it to the reverse clutch piston sub-assembly.

Text in Illustration
*1 O-ring


c.
D028511E10
0.427,0.438 0.552,0.438 0.552,0.438 0.833,0.719 false 1.615,0.188 1.74,0.188 1.74,0.188 2.01,0.469 false 0.229,0.323 0.396,0.479 0.167,0.156 10 false *1 1.396,0.094 1.563,0.25 0.167,0.156 10 false *2

Press the reverse clutch drum sub-assembly into the reverse clutch piston sub-assembly with both hands.

Text in Illustration
*1 Reverse Clutch Piston Sub-assembly
*2 Reverse Clutch Drum Sub-assembly

NOTICE:

Be careful not to damage the O-rings.



Hide 35047 31.INSTALL REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D028510E21
1.948,0.292 1.729,0.125 1.729,0.125 1.594,0.125 false 1.354,0.656 1.135,0.5 1.135,0.5 1.01,0.5 false 0.563,0.865 0.354,0.708 0.354,0.708 0.219,0.708 false 0.021,0.604 0.177,0.781 0.156,0.177 10 false *1 0.813,0.385 0.969,0.563 0.156,0.177 10 false *2 1.396,0.021 1.552,0.198 0.156,0.177 10 false *3

Coat a new O-ring with ATF, and install it to the reverse clutch piston sub-assembly.

Text in Illustration
*1 Reverse Clutch Return Spring Sub-assembly
*2 O-ring
*3 Reverse Clutch Piston Sub-assembly


b.

Install the reverse clutch return spring sub-assembly to the reverse clutch piston sub-assembly.


Hide 35688 32.INSTALL NO. 3 CLUTCH BALANCER

a.
D028509E18
1.708,0.885 2.479,0.573 2.479,0.573 2.26,0.927 true 2.531,0.385 2.875,0.583 0.344,0.198 10 false SST

Install the No. 3 clutch balancer to the reverse clutch return spring sub-assembly.


b.

Place SST on the No. 3 clutch balancer, and compress the reverse clutch return spring sub-assembly with a press.

SST
09387-00070  

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




d.
D031539E15
0.771,2.406 0.948,2.063 false 0.948,1.01 1.125,0.677 false 1.125,0.531 1.323,0.698 0.198,0.167 10 false *1 0.302,0.406 0.5,0.573 0.198,0.167 10 false *a 0.958,1.896 1.156,2.063 0.198,0.167 10 false *1 0.292,1.781 0.49,1.948 0.198,0.167 10 false *b

Set the end gap of the snap ring in the No. 3 clutch balancer as shown in the illustration.

Text in Illustration
*1 Snap Ring
*a Correct
*b Incorrect


Hide 35667A 33.INSTALL NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)

a.
C109338E03
0.746,1.037 0.906,1.238 0.160,0.201 10 *1 2.527,0.845 2.702,1.046 0.174,0.201 10 *2 0.72,0.637 0.903,0.838 0.184,0.201 10 *3 1.101,1.56 1.254,1.56 false 1.101,1.961 1.279,1.961 false 1.096,2.316 1.254,2.316 false 1.254,2.711 1.096,2.711 1.096,2.711 1.096,1.15 false 2.17,0.97 2.509,0.97 false 2.17,1.375 2.324,1.375 false 2.17,1.764 2.327,1.764 false 2.159,2.175 2.326,2.175 false 2.17,2.534 2.327,2.534 2.327,2.534 2.327,0.97 false 0.916,1.15 1.254,1.15 false 0.926,0.75 1.264,0.75 false

Install the direct clutch flange, 5 No. 2 clutch discs and the 5 No. 2 clutch plates to the reverse clutch drum sub-assembly.

Text in Illustration
*1 No. 2 Clutch Plate
*2 No. 2 Clutch Disc
*3 Direct Clutch Flange

Installation order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3


NOTICE:

Make sure that the discs, plates and the flange are installed in the correct order.



b.
U147225E05
2.042,0.958 2.073,0.948 2.073,0.948 2.094,0.927 false 2.063,0.646 2.313,0.292 2.313,0.292 2.448,0.292 false 2.448,0.188 2.604,0.365 0.156,0.177 10 false *1

Using a screwdriver, install the 2 snap rings to the reverse clutch drum sub-assembly.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the reverse clutch drum sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35649 35.INSTALL REVERSE CLUTCH FLANGE

a.
D028506

Install the reverse clutch flange to the reverse clutch drum sub-assembly.


Hide 35659 36.INSTALL REVERSE CLUTCH REACTION SLEEVE

a.
C128066E03
1.757,1.281 1.974,1.448 0.217,0.167 10 *4 1.748,0.656 1.954,0.831 0.206,0.175 10 *5 1.756,1.895 1.937,2.059 0.181,0.165 10 *1 1.754,1.642 1.943,1.810 0.189,0.167 10 *3 0.097,2.14 0.265,2.326 0.167,0.186 10 *2 1.435,0.757 1.731,0.757 false 1.378,1.371 1.731,1.371 false 1.428,1.734 1.737,1.734 false 1.395,1.983 1.737,1.983 false 0.289,2.228 0.515,2.228 false 1.393,3.597 1.554,3.597 1.554,3.597 1.554,1.983 false 1.393,3.065 1.554,3.065 false 1.392,2.513 1.554,2.513 false 0.515,3.312 0.391,3.312 0.391,3.312 0.391,2.228 false 0.515,2.758 0.391,2.758 false

Install the clutch cushion plate, reverse clutch flange, 4 No. 3 clutch discs, 3 No. 3 clutch plates and the reverse clutch reaction sleeve to the reverse clutch drum sub-assembly.

Text in Illustration
*1 No. 3 Clutch Disc
*2 No. 3 Clutch Plate
*3 Reverse Clutch Flange
*4 Clutch Cushion Plate
*5 Reverse Clutch Reaction Sleeve

Installation order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *3 - *4 - *5


NOTICE:

Make sure that the discs, plates, flange, sleeve and the cushion plate are installed in the correct order.



b.
U118104E08
2.563,0.885 2.625,0.792 false 2.594,0.885 2.844,0.479 2.844,0.479 3.01,0.479 true 3.063,0.406 3.219,0.583 0.156,0.177 10 false *1

Using a screwdriver, install the snap ring to the reverse clutch piston sub-assembly.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the reverse clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35659 38.REMOVE REVERSE CLUTCH REACTION SLEEVE

a.
U118104E08
2.563,0.885 2.625,0.792 false 2.594,0.885 2.844,0.479 2.844,0.479 3.01,0.479 true 3.063,0.406 3.219,0.583 0.156,0.177 10 false *1

Using a screwdriver, remove the snap ring from the reverse clutch piston sub-assembly.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the reverse clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



b.
D029843

Remove the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 4 No. 3 clutch discs and the 3 No. 3 clutch plates from the reverse clutch drum sub-assembly.


Hide 35602A 39.INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY

a.
D031383E10
2.146,0.354 1.938,0.146 1.938,0.146 1.781,0.146 false 0.958,0.573 0.76,0.365 0.76,0.365 0.604,0.365 false 1.583,0.063 1.74,0.24 0.156,0.177 10 false *1 0.396,0.281 0.552,0.458 0.156,0.177 10 false *2

Install the coast clutch piston to the forward clutch piston sub-assembly.

Text in Illustration
*1 Coast Clutch Piston
*2 Forward Clutch Piston Sub-assembly


b.
C141896E01
0.291,1.213 0.461,1.373 0.170,0.161 10 *1 0.749,1.303 0.486,1.303 false

Coat a new O-ring with ATF, and install it to the input shaft.

Text in Illustration
*1 O-ring


c.

Install the forward clutch piston sub-assembly to the input shaft.


Hide 35668 40.INSTALL NO. 1 CLUTCH BALANCER

a.
C109344E02
0.312,0.356 0.468,0.538 0.156,0.181 10 *1 0.818,0.647 0.619,0.448 0.619,0.448 0.492,0.448 false

Coat a new D-ring with ATF, and install it to the No. 1 clutch balancer.

Text in Illustration
*2 D-ring


b.
C109343E01
0.117,0.402 0.273,0.584 0.156,0.181 10 *1 0.117,1.253 0.273,1.435 0.156,0.181 10 *2 0.588,0.494 0.296,0.494 false 0.665,1.347 0.317,1.347 false

Install the No. 1 clutch balancer and the forward clutch return spring sub-assembly to the input shaft.

Text in Illustration
*1 No. 1 Clutch Balancer
*2 Forward Clutch Return Spring Sub-assembly

NOTICE:

Be careful not to damage the D-ring.



c.
C261812E04
2.896,0.833 3.125,1.625 true 2.531,1.01 3.125,1.625 true 2.958,1.646 3.281,1.802 0.323,0.156 10 false SST

Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.

SST
09387-00110  

NOTICE:

Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



d.

Using SST, Install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




e.
C109354E05
0.919,0.405 1.115,0.607 0.196,0.201 10 *1 0.899,0.524 0.79,0.524 0.79,0.524 0.79,0.991 false 0.236,0.415 0.403,0.617 0.168,0.201 10 *a 0.721,1.818 0.917,2.019 0.196,0.201 10 *1 0.699,1.938 0.634,1.938 0.634,1.938 0.634,2.418 false 0.236,1.829 0.432,2.03 0.196,0.201 10 *b

Set the end gap of the snap ring in the No. 1 clutch balancer as shown in the illustration.

Text in Illustration
*1 Snap Ring
*a Correct
*b Incorrect


Hide 35685 41.INSTALL NO. 4 CLUTCH DISC (COAST CLUTCH DISC)

a.
U146953E04
1.292,1.01 1.427,1.01 false 1.281,0.771 1.427,0.771 false 1.292,0.531 1.427,0.531 false 0.385,0.625 0.229,0.625 0.229,0.625 0.229,1.552 false 0.385,0.865 0.229,0.865 false 0.396,1.115 0.229,1.115 false 0.385,1.375 0.229,1.375 false 0.24,0.365 0.385,0.365 false 0.073,0.281 0.281,0.479 0.208,0.198 10 false *3 0.135,1.563 0.323,1.76 0.188,0.198 10 false *1 1.542,0.219 1.74,0.417 0.198,0.198 10 false *2

Install the coast clutch flange, 4 No. 4 clutch discs and the 4 No. 4 clutch plates to the forward clutch piston sub-assembly.

Text in Illustration
*1 No. 4 Clutch Plate
*2 No. 4 Clutch Disc
*3 Coast Clutch Flange

Installation order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3


NOTICE:

Make sure that the discs, plates and the flange are installed in the correct order.



b.
C162748E01
2.09,0.289 2.260,0.449 0.170,0.161 10 *1 1.634,0.864 2.047,0.375 false 1.591,0.994 1.651,0.926 false 1.577,0.869 1.627,0.805 false 1.57,0.751 1.617,0.686 false 1.562,0.632 1.608,0.563 false

Using a screwdriver, install the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the forward clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35633B 43.INSTALL NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)

a.
C109356E09
2.219,0.927 2.51,0.927 false 1.177,0.698 0.927,0.698 false 1.219,1.063 0.927,1.063 false 1.177,2.604 0.927,2.604 false 1.177,2.385 1.031,2.385 1.031,2.385 1.031,1.063 false 1.177,1.969 1.031,1.969 false 1.177,1.542 1.031,1.542 false 2.219,2.208 2.406,2.208 2.406,2.208 2.406,0.927 false 2.219,1.781 2.406,1.781 false 2.219,1.365 2.406,1.365 false 2.531,0.833 2.708,0.99 0.177,0.156 10 false *3 0.729,2.521 0.906,2.698 0.177,0.177 10 false *1 0.719,0.979 0.865,1.156 0.146,0.177 10 false *2 0.729,0.604 0.885,0.792 0.156,0.188 10 false *4

Install the forward clutch flange, 4 No. 1 clutch discs, 4 No. 1 clutch plates and the clutch cushion plate to the input shaft.

Text in Illustration
*1 Clutch Cushion Plate
*2 No. 1 Clutch Plate
*3 No. 1 Clutch Disc
*4 Forward Clutch Flange

Installation order:

*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *4


NOTICE:

Make sure that the discs, plates, flange and the cushion plate are installed in the correct order.



b.
U147227E04
0.906,1.583 0.417,2.146 false 2.552,1.323 2.917,1.49 2.917,1.49 2.531,2.146 false 1.375,0.792 1.427,0.708 false 1.344,0.719 1.375,0.594 false 1.313,0.615 1.021,0.615 false 0.844,0.531 1.021,0.708 0.177,0.177 10 false *1

Using a screwdriver, install the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the input shaft.


HINT:

Tape the screwdriver tip before use.



Hide 35617 45.INSTALL CLUTCH DRUM OIL SEAL RING

a.
D031399

Coat 4 new clutch drum oil seal rings with ATF.


b.

Squeeze the ends of the 4 clutch drum oil seal rings together, and install them to the input shaft groove.

NOTICE:

Do not expand the ring ends excessively.


HINT:

After installing the clutch drum oil seal rings, check that they rotate smoothly.



Hide 46.INSTALL INPUT SHAFT

a.
D031522

Install the input shaft to the reverse clutch drum sub-assembly.


b.
C109352E10
1.906,0.313 2.156,0.313 false 1.177,0.615 1.344,0.615 1.344,0.615 1.542,0.646 false 0.969,0.531 1.156,0.729 0.188,0.198 10 false *2 2.219,0.24 2.406,0.438 0.188,0.198 10 false *1

Install the input shaft rear thrust bearing race and the thrust needle roller bearing to the input shaft.

Text in Illustration
*1 Thrust Needle Roller Bearing
*2 Input Shaft Rear Thrust Bearing Race

Bearing and Race Diameter
Item Inside Outside
Thrust needle roller bearing 20.0 mm (0.787 in.) 41.0 mm (1.614 in.)
Input shaft rear thrust bearing race 20.0 mm (0.787 in.) 35.6 mm (1.402 in.)


Hide 35790H 47.INSTALL NO. 4 ONE-WAY CLUTCH ASSEMBLY

a.
C109362E07
2.5,0.323 2.281,0.104 2.281,0.104 2.156,0.104 false 1.865,0.521 1.635,0.292 1.635,0.292 1.51,0.292 false 1.031,0.719 0.802,0.49 0.802,0.49 0.677,0.49 false 0.49,0.396 0.646,0.573 0.156,0.177 10 false *1 1.323,0.198 1.479,0.375 0.156,0.177 10 false *2 1.969,0.01 2.125,0.188 0.156,0.177 10 false *3

Install the No. 2 clutch hub thrust washer and the No. 4 one-way clutch assembly to the coast clutch hub sub-assembly.

Text in Illustration
*1 Coast Clutch Hub Sub-assembly
*2 No. 2 Clutch Hub Thrust Washer
*3 No. 4 One-way Clutch Assembly


Hide 35064 48.INSTALL COAST CLUTCH HUB SUB-ASSEMBLY

a.
D031377

Install the coast clutch hub sub-assembly to the reverse clutch drum sub-assembly.


Hide 35061 49.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C109367E16
0.333,0.531 0.229,0.531 0.229,0.531 0.229,1.281 false 3,0.281 3.135,0.281 3.135,0.281 3.135,0.51 false 2.698,1.177 2.698,1.531 false 0.354,0.448 0.542,0.667 0.188,0.219 10 false *1 2.604,1.552 2.792,1.771 0.188,0.219 10 false *2 2.823,0.198 3.01,0.417 0.188,0.219 10 false *3

Install the 2 thrust needle roller bearings and the No. 2 thrust bearing race to the forward clutch hub sub-assembly.

Text in Illustration
*1 Thrust Needle Roller Bearing A
*2 Thrust Needle Roller Bearing B
*3 No. 2 Thrust Bearing Race

Bearing and Race Diameter
Item Inside Outside
Thrust needle roller bearing A 42.5 mm (1.673 in.) 61.2 mm (2.409 in.)
Thrust needle roller bearing B 33.3 mm (1.311 in.) 51.2 mm (2.016 in.)
No. 2 thrust bearing race 31.0 mm (1.220 in.) 48.0 mm (1.890 in.)


b.
D031376E07
0.479,0.625 0.333,0.469 false 0.531,1.635 0.375,1.479 false 0.135,0.375 0.302,0.531 0.167,0.156 10 false *1 0.177,1.385 0.344,1.542 0.167,0.156 10 false *2

Install the No. 3 clutch hub thrust washer and the forward clutch hub sub-assembly to the reverse clutch drum sub-assembly.

Text in Illustration
*1 Forward Clutch Hub Sub-Assembly
*2 No. 3 Clutch Hub Thrust Washer


Hide 35677C 50.INSTALL NO. 3 CLUTCH DISC (REAR CLUTCH DISC)

a.
C122852E03
0.09,1.472 0.260,1.632 0.170,0.161 10 *1 0.263,1.555 0.507,1.555 false 0.09,0.352 0.260,0.513 0.170,0.161 10 *4 0.263,0.435 0.507,0.435 false 0.358,1.293 0.507,1.293 false 0.358,1.032 0.507,1.032 false 0.507,0.77 0.358,0.77 0.358,0.77 0.358,1.555 false 1.681,1.29 1.851,1.451 0.170,0.161 10 *2 1.68,1.373 1.437,1.373 false 1.681,0.519 1.851,0.679 0.170,0.161 10 *3 1.68,0.602 1.437,0.602 false 1.585,1.112 1.437,1.112 false 1.437,0.851 1.585,0.851 1.585,0.851 1.585,1.373 false

Install the clutch cushion plate, reverse clutch flange, 4 No. 3 clutch discs and the 3 No. 3 clutch plates to the reverse clutch hub sub-assembly.

Text in Illustration
*1 No. 3 Clutch Disc
*2 No. 3 Clutch Plate
*3 Reverse Clutch Flange
*4 Clutch Cushion Plate

Installation order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *3 - *4


NOTICE:

Make sure that the discs, plates, flange and the cushion plate are installed in the correct order.



Hide 35659 51.INSTALL REVERSE CLUTCH REACTION SLEEVE

a.
D027998

Install the reverse clutch reaction sleeve to the reverse clutch hub sub-assembly.


Hide 35049 52.INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

a.
D027997

Install the reverse clutch hub sub-assembly to the reverse clutch drum sub-assembly.


b.
U147224E05
2.302,1.104 2.313,1.104 2.313,1.104 2.344,1.094 false 2.292,1.063 2.313,1.063 2.313,1.063 2.365,1.031 false 2.344,1.01 2.667,0.719 2.667,0.719 2.792,0.719 false 2.813,0.615 2.969,0.792 0.156,0.177 10 false *1

Using a screwdriver, install the snap ring to the reverse clutch piston sub-assembly.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the reverse clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35780B 53.INSTALL NO. 2 ONE-WAY CLUTCH ASSEMBLY

a.
D027994E12
2.802,0.323 2.552,0.146 2.552,0.146 2.427,0.146 false 2.271,0.542 2.031,0.365 2.031,0.365 1.906,0.365 false 2.25,0.052 2.406,0.229 0.156,0.177 10 false *1 1.708,0.271 1.865,0.448 0.156,0.177 10 false *2

Install the input shaft clutch drum thrust washer and the No. 2 one-way clutch assembly to the clutch drum and input shaft assembly.

Text in Illustration
*1 No. 2 One-way Clutch Assembly
*2 Input Shaft Clutch Drum Thrust Washer


Hide 54.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C109327E12
0.823,1.938 0.698,1.938 0.698,1.938 0.458,1.573 false 1.052,1.677 0.938,1.677 0.938,1.677 0.74,1.365 false 1.25,1.531 1.135,1.531 1.135,1.531 0.979,1.292 false 3.031,1.167 3.031,0.938 false 0.854,1.875 1.052,2.042 0.198,0.167 10 false *1 1.094,1.615 1.292,1.781 0.198,0.167 10 false *2 1.323,1.448 1.521,1.615 0.198,0.167 10 false *3 2.958,1.188 3.156,1.354 0.198,0.167 10 false *4

Install the input shaft front thrust needle roller bearing and the thrust needle roller bearing to the clutch drum and input shaft assembly.

Text in Illustration
*1 Thrust Needle Roller Bearing
*2 Input Shaft Front Thrust Bearing Race
*3 Input Shaft Front Thrust Needle Roller Bearing
*4 Clutch Drum Thrust Washer

Bearing and Race Diameter
Item Inside Outside
Thrust needle roller bearing 71.9 mm (2.831 in.) 85.6 mm (3.370 in.)
Input shaft front thrust bearing race 37.0 mm (1.457 in.) 51.2 mm (2.016 in.)
Input shaft front thrust needle roller bearing 33.5 mm (1.319 in.) 48.0 mm (1.890 in.)


b.

Coat the input shaft front thrust bearing race and the clutch drum thrust washer with petroleum jelly, and install them onto the clutch drum and input shaft assembly.


c.
D029833

Install the clutch drum and input shaft assembly to the automatic transmission case sub-assembly.


Hide 55.INSTALL OIL PUMP ASSEMBLY

a.
C122832E09
2.146,0.167 2.333,0.167 2.333,0.167 2.479,0.302 false 1.813,1.688 1.906,1.781 1.906,1.781 2.156,1.781 false 0.708,1.344 0.708,0.698 0.708,0.698 0.594,0.698 false 1.938,0.104 2.188,0.292 0.25,0.188 10 false *2 0.438,0.604 0.688,0.792 0.25,0.188 10 false *1 2.198,1.698 2.448,1.885 0.25,0.188 10 false *3

Install the No. 1 thrust bearing race to the oil pump assembly.

Text in Illustration
*1 No. 1 Thrust Bearing Race
*2 Oil Pump Assembly
*3 O-ring

Race Diameter
Item Inside Outside
No. 1 thrust bearing race 74.2 mm (2.921 in.) 87.7 mm (3.453 in.)


b.

Coat a new O-ring with ATF, and install it to the oil pump assembly.


c.

Place the oil pump assembly through the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



d.

Hold the input shaft, and lightly press the oil pump assembly to slide the clutch drum oil seal rings into the clutch drum and input shaft assembly.


e.
C106934

Install the 9 bolts.

Torque:
21 N*m (215 kgf*cm, 16 ft.*lbf)


Hide 35506F 57.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C210560E01
1.906,1.87 2.253,2.040 0.347,0.170 10 SST 1.595,0.59 1.859,1.948 1.859,1.948 1.511,2.773 false

Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals to the automatic transmission case sub-assembly.

SST
09350-30020  (09350-07110)


b.

Coat the manual valve lever shaft oil seal lips with MP grease.


Hide 35505 58.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.
D031556E16
0.76,1.115 0.76,1.406 false 1.042,0.979 1.042,0.188 1.042,0.188 0.917,0.188 false 0.688,0.094 0.865,0.323 0.177,0.229 10 false *1 0.677,1.427 0.854,1.656 0.177,0.229 10 false *2

Install a new spacer to the manual valve lever sub-assembly.

Text in Illustration
*1 Spacer
*2 Manual Valve Lever Sub-assembly


b.

Install the manual valve lever shaft to the automatic transmission case sub-assembly through the manual valve lever sub-assembly.


c.
D028799

Using a hammer, drive in a new spring pin.


d.
D031557

Align the manual valve lever indentation with the spacer hole, and stake them together with a punch.


e.

Make sure that the shaft rotates smoothly.


Hide 35556 59.INSTALL PARKING LOCK PAWL SHAFT

a.

Install a new E-ring to the parking lock pawl shaft.


b.
C122830E07
0.292,0.49 1.146,0.438 false 2,0.865 2.198,0.865 false 1.781,1.635 2.188,1.604 false 1.865,1.115 2.24,1 false 0.146,0.396 0.344,0.552 0.198,0.156 10 false *1 1.76,0.792 1.969,0.979 0.208,0.188 10 true *2 1.646,1.031 1.854,1.219 0.208,0.188 10 true *3 1.573,1.583 1.781,1.771 0.208,0.188 10 true *4

Install the parking lock pawl, parking lock pawl shaft and the torsion spring to the automatic transmission case sub-assembly.

Text in Illustration
*1 Parking Lock Pawl
*2 E-ring
*3 Parking Lock Pawl Shaft
*4 Torsion Spring


Hide 35501 60.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
D031551

Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.


Hide 35595 61.INSTALL PARKING LOCK PAWL BRACKET

a.
D031361

Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts.

Torque:
7.3 N*m (74 kgf*cm, 65 in.*lbf)


b.
D028801E21
0.688,1.323 0.448,1.177 true 2.938,0.208 2.417,0.208 true 0.74,1.646 0.74,1.792 false 2.24,0.125 2.458,0.302 0.219,0.177 10 false *2 0.271,1.094 0.438,1.25 0.167,0.156 10 false *1 0.656,1.813 0.823,1.969 0.167,0.156 10 false *3

Shift the manual valve lever sub-assembly to the P position, and confirm that the rear planetary gear is correctly locked by the parking lock pawl.

Text in Illustration
*1 Rear Planetary Gear
*2 Manual Valve Lever Sub-assembly
*3 Parking Lock Pawl


Hide 62.INSTALL B-1 ACCUMULATOR VALVE

a.
C122853

Install the spring and the B-1 accumulator valve to the hole.

B-1 Accumulator Spring
Free Length Outer Diameter Color
46.36 mm (1.825 in.) 17.1 mm (0.673 in.) Natural


Hide 35426D 63.INSTALL C-3 ACCUMULATOR PISTON

a.
C369190E01
1.656,1.458 1.115,0.698 1.115,0.698 0.969,0.698 false 1.635,0.906 1.292,0.448 1.292,0.448 1.177,0.448 false 2.74,0.417 3.021,0.417 3.021,0.417 3.021,0.844 false 2.74,0.635 3.01,0.635 false 0.781,0.625 0.99,0.833 0.208,0.208 10 false *2 1,0.354 1.208,0.563 0.208,0.208 10 false *3 2.927,0.875 3.135,1.083 0.208,0.208 10 false *1

Coat 2 new O-rings with ATF, and install them to the C-3 accumulator piston.

Text in Illustration
*1 O-ring
*2 Inner Spring
*3 Outer Spring


b.

Install the 2 springs and the C-3 accumulator piston to the hole.

C-3 Accumulator Spring
Spring Free Length Outer Diameter Color
Inner 44.0 mm (1.732 in.) 14.0 mm (0.551 in.) Yellow
Outer 76.65 mm (3.018 in.) 20.1 mm (0.791 in.) White


Hide 35427K 64.INSTALL B-3 ACCUMULATOR PISTON

a.
C224346

Using a screwdriver, install the spring sub-assembly to the B-3 accumulator piston with the snap ring.

B-3 Accumulator Spring Sub-assembly
Free Length Coil Outer Diameter Color
25.77 mm (1.015 in.) 16.3 mm (0.642 in.) Purple

NOTICE:

Be careful not to damage the B-3 accumulator piston.


HINT:

Tape the screwdriver tip before use.



b.
C369191E01
1.979,1.01 1.406,0.604 1.406,0.604 1.281,0.604 false 3.094,0.729 3.26,0.729 false 3.094,0.521 3.26,0.521 3.26,0.521 3.26,0.906 false 1.073,0.531 1.26,0.74 0.188,0.208 10 false *2 3.177,0.927 3.365,1.135 0.188,0.208 10 false *1

Coat 2 new O-rings with ATF, and install them to the B-3 accumulator piston.

Text in Illustration
*1 O-ring
*2 Spring


c.

Install the spring and the B-3 accumulator piston to the hole.

B-3 Accumulator Spring
Free Length Outer Diameter Color
70.5 mm (2.776 in.) 19.7 mm (0.776 in.) Purple


Hide 35425A 65.INSTALL C-2 ACCUMULATOR PISTON

a.
C224346

Using a screwdriver, install the spring sub-assembly to the C-2 accumulator piston with the snap ring.

C-2 Accumulator Spring Sub-assembly
Free Length Coil Outer Diameter Color
15.16 mm (0.597 in.) 11.3 mm (0.447 in.) Natural

NOTICE:

Be careful not to damage the C-2 accumulator piston.


HINT:

Tape the screwdriver tip before use.



b.
C369193E01
2.146,1.01 1.729,0.708 1.729,0.708 1.625,0.708 false 3.25,0.792 3.323,0.792 false 3.24,0.573 3.323,0.573 3.323,0.573 3.323,1.01 false 1.458,0.646 1.615,0.844 0.156,0.198 10 false *2 3.24,1.031 3.396,1.229 0.156,0.198 10 false *1

Coat 2 new O-rings with ATF, and install them to the C-2 accumulator piston.

Text in Illustration
*1 O-ring
*2 Spring


c.

Install the spring and the C-2 accumulator piston to the hole.

C-2 Accumulator Spring
Free Length Outer Diameter Color
65.07 mm (2.562 in.) 16.2 mm (0.638 in.) Pink


Hide 35251 66.INSTALL CHECK BALL BODY

a.
D027914E34
1.531,1.24 0.854,1.24 true 0.865,0.406 1.281,0.406 false 0.698,0.313 0.875,0.5 0.177,0.188 10 false *1 0.635,1.167 0.823,1.323 0.188,0.156 10 false *2

Install the check ball body and the compression spring to the automatic transmission case sub-assembly.

Text in Illustration
*1 Check Ball Body
*2 Compression Spring


Hide 35159 67.INSTALL BRAKE DRUM GASKET

a.
D027969

Install 3 new brake drum gaskets to the automatic transmission case sub-assembly.


Hide 35145C 68.INSTALL TRANSMISSION CASE GASKET

a.
D027968

Install 3 new transmission case gaskets to the automatic transmission case sub-assembly.


Hide 35410 69.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C109330E12
1.865,0.927 2.167,0.365 2.167,0.365 2.448,0.365 true 2.125,1.052 2.677,1.771 true 2.49,0.271 2.677,0.49 0.188,0.219 10 false *1 2.698,1.781 2.885,2 0.188,0.219 10 false *2

Connect the manual valve connecting rod sub-assembly to the manual valve lever sub-assembly.

Text in Illustration
*1 Manual Valve Connecting Rod Sub-assembly
*2 Manual Valve Lever Sub-assembly


b.
C109368E09
0.531,0.344 0.667,0.198 0.667,0.198 0.75,0.333 true 0.208,0.823 0.521,0.823 true 0.51,0.635 0.208,0.823 0.208,0.823 0.458,1.271 true 0.438,1.51 0.229,1.583 0.229,1.583 0.438,1.646 true 1.031,1.646 1.104,1.958 true 1.813,1.615 1.552,1.958 true 1.875,1.76 1.917,1.958 1.917,1.958 2.094,1.823 true 2.458,1.823 2.542,1.948 2.542,1.948 2.656,1.823 true 3.052,1.74 3.24,1.625 3.24,1.625 3.052,1.469 true 3.063,0.771 3.24,0.771 true 0.833,1.833 0.781,1.958 true 2.49,1.521 3.219,1.146 3.219,1.146 3.073,1.104 true 0.719,1.979 0.854,2.135 0.135,0.156 10 false A 0.104,1.521 0.24,1.677 0.135,0.156 10 false A 1.854,1.969 1.99,2.125 0.135,0.156 10 false A 2.479,1.969 2.615,2.125 0.135,0.156 10 false A 3.26,1.542 3.385,1.698 0.125,0.156 10 false A 0.625,0.021 0.76,0.177 0.135,0.156 10 false A 0.052,0.74 0.177,0.896 0.125,0.156 10 false B 1.073,1.979 1.198,2.135 0.125,0.156 10 false B 3.24,1.073 3.365,1.229 0.125,0.156 10 true D 1.469,1.958 1.594,2.115 0.125,0.156 10 false C 3.26,0.698 3.385,0.854 0.125,0.156 10 false C

Install the transmission valve body assembly to the automatic transmission case sub-assembly with the 19 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.


Bolt length:
Bolt A:

25 mm (0.984 in.)

Bolt B:

36 mm (1.42 in.)

Bolt C:

45 mm (1.77 in.)

Bolt D:

50 mm (1.97 in.)



c.
C106931

Install the detent spring and the detent spring cover to the transmission valve body assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82125J 70.INSTALL TRANSMISSION WIRE

a.
C101505E12
1.396,0.594 1.177,0.594 false 0.979,0.51 1.229,0.708 0.25,0.198 10 false *1

Coat a new O-ring with ATF, and install it to the transmission wire.

Text in Illustration
*1 O-ring


b.
D027912

Install the transmission wire with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
C122840

Connect the 9 solenoid valve connectors.


d.

Coat the ATF temperature sensor O-ring with ATF.


e.
C122839

Install the ATF temperature sensor and the temperature sensor clamp with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.
C257575

Install the valve body wire harness clamp with the 2 bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


g.

Engage the wire harness clamp.


Hide 35330 71.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C258477E01
0.997,1.238 1.872,1.771 false 1.894,1.725 2.059,1.899 0.165,0.174 10 *1

Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.

Text in Illustration
*1 O-ring


b.
C258476

Install the valve body oil strainer assembly to the transmission valve body assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35106 72.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.
C109359E04
2.311,0.344 2.492,0.563 0.180,0.219 10 *1 1.004,0.605 1.004,0.449 1.004,0.449 2.26,0.449 false 2.114,1.103 2.115,0.449 false 1.395,0.985 1.395,0.449 false

Install the 3 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly.

Text in Illustration
*1 Transmission Oil Cleaner Magnet


b.
C256218

Install a new automatic transmission oil pan gasket and the automatic transmission oil pan sub-assembly with the 20 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Install the drain plug and a new gasket.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Using a socket hexagon wrench 5 mm, install the overflow plug and a new gasket.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35770A 73.INSTALL OUTPUT SHAFT THRUST BEARING

a.

Install the output shaft thrust bearing race, output shaft thrust bearing and the rear output shaft thrust bearing race to the output shaft of the rear planetary gear assembly.

Bearing and Race Diameter
Item Inside Outside
Output shaft thrust bearing race 37.0 mm (1.457 in.) 51.2 mm (2.016 in.)
Output shaft thrust bearing 36.1 mm (1.421 in.) 52.5 mm (2.067 in.)
Rear output shaft thrust bearing race 36.1 mm (1.421 in.) 51.0 mm (2.007 in.)


b.
C106923

Using a snap ring expander, install the snap ring.


c.
C109333

Using a feeler gauge, measure the clearance between the snap ring and the rear output shaft thrust bearing race.

Standard clearance:

0.02 to 0.12 mm (0.000787 to 0.00472 in.)


If the clearance is outside the standard range, select another rear output shaft thrust bearing race that brings the clearance within the standard range.

HINT:

There are 12 different thicknesses for the rear output shaft thrust bearing race.


Race Thickness
Part No. Mark Thickness
SU003-03819
C257412

3.80 mm (0.150 in.)
SU003-03820
C257413

3.85 mm (0.152 in.)
SU003-03821
C257414

3.90 mm (0.154 in.)
SU003-03822
C257415

3.95 mm (0.156 in.)
SU003-03823
C257416

4.00 mm (0.157 in.)
SU003-03824
C257417

4.05 mm (0.159 in.)
SU003-03825
C257418

4.10 mm (0.161 in.)
SU003-03826
C257419

4.15 mm (0.163 in.)
SU003-03827
C257420

4.20 mm (0.165 in.)
SU003-03828
C257421

4.25 mm (0.167 in.)
SU003-03829
C257422

4.30 mm (0.169 in.)
SU003-0383
C257423

4.35 mm (0.171 in.)


Hide 35108R 74.INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

a.
C224433E01
0.543,0.733 0.824,0.895 false 0.179,0.632 0.507,0.793 0.327,0.161 10 SST

Using SST and a hammer, drive in the automatic transmission extension housing oil seal to the extension housing sub-assembly.

SST
09309-37010  

Drive in depth:

5.4 to 5.8 mm (0.213 to 0.228 in.)



b.

Coat the lip of a new automatic transmission extension housing oil seal with MP grease.


Hide 35146 75.INSTALL EXTENSION HOUSING DUST DEFLECTOR

a.
C106922E05
1.052,0.51 1.427,0.51 false 0.74,0.448 1.125,0.688 0.385,0.24 10 false SST

Using SST and a press, install a new extension housing dust deflector to the extension housing sub-assembly.

SST
09950-60020  (09951-01030)


Hide 35015L 76.INSTALL TRANSMISSION CASE ADAPTER RADIAL BALL BEARING

a.
C106927

Install the transmission case adapter radial ball bearing to the extension housing sub-assembly.


b.

Using snap ring pliers, install the snap ring to the extension housing sub-assembly.


Hide 35108 77.INSTALL EXTENSION HOUSING SUB-ASSEMBLY

a.

Clean and degrease the threads of the 6 bolts and the contact surfaces of the case and the housing with non-residue solvent.


b.
C108612E07
2.656,0.656 2.313,0.656 true 2.708,0.552 2.896,0.75 0.188,0.198 10 false *a

Apply seal packing to the extension housing sub-assembly as shown in the illustration.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the extension housing sub-assembly within 10 minutes after the seal packing application.



c.
A057108E68
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.375,0.323 0.177,0.167 10 false *1

Apply adhesive to 2 or 3 threads on the end of the 6 bolts.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.
C106925E06
0.802,0.552 1,0.75 0.198,0.198 10 false B 2.177,0.625 2.375,0.823 0.198,0.198 10 true B 2.01,1.729 2.208,1.927 0.198,0.198 10 false A 0.885,1.521 1.083,1.719 0.198,0.198 10 true A 0.708,1.083 0.906,1.281 0.198,0.198 10 false B 2.281,1.229 2.479,1.427 0.198,0.198 10 true B

Install the extension housing sub-assembly to the automatic transmission case sub-assembly with the 6 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)

HINT:

Each bolt length is indicated below.


Bolt length:
for Bolt A:

35 mm (1.378 in.)

for Bolt B:

45 mm (1.772 in.)



Hide 35111 78.INSTALL AUTOMATIC TRANSMISSION HOUSING

a.

Clean and degrease the bolts and the bolt holes with non-residue solvent.


b.
C263942

Install the automatic transmission housing to the automatic transmission case sub-assembly with the 6 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)


c.
A057108E68
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.375,0.323 0.177,0.167 10 false *1

Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.
C263943E03
1.375,1.885 1.49,2.031 0.115,0.146 10 true A 1.958,1.833 2.073,1.979 0.115,0.146 10 false A 2.469,1.604 2.583,1.75 0.115,0.146 10 true B 0.875,1.677 0.99,1.823 0.115,0.146 10 false B

Install the automatic transmission housing to the automatic transmission case sub-assembly with the 4 bolts.

Torque:
Bolt A (M10 bolt) : 34 N*m (345 kgf*cm, 25 ft.*lbf)
Bolt B (M12 bolt) : 57 N*m (579 kgf*cm, 42 ft.*lbf)


Hide 35104A 79.INSTALL AUTOMATIC TRANSMISSION CASE PLUG

a.
C235144

Coat a new O-ring with ATF, and install it to the automatic transmission case plug.


b.

Using "TORX" socket wrench T55, install the automatic transmission case plug to the automatic transmission case sub-assembly.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


c.
C235143

Coat 5 new O-ring with ATF, and install it to the 5 automatic transmission case plug.


d.

Install the 5 automatic transmission case plugs to the automatic transmission case sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35122 80.INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

a.
B645477E01
3.031,1.708 3.031,1.417 false 2.969,1.74 3.281,1.938 0.313,0.198 10 false *1

As shown in the illustration, apply seal packing to the area where the automatic transmission breather tube is inserted, and then temporarily install the automatic transmission breather tube.

HINT:
·

Degrease the seal surface of the automatic transmission breather tube and transmission case before applying seal packing.

·

Install the automatic transmission breather tube within 10 minutes after applying seal packing.



Text in Illustration
*1 Seal Packing

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



b.
B645476

Install the automatic transmission breather tube with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 89413B 81.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C230501

Coat 2 new O-rings with ATF, and install them to the 2 transmission revolution sensors.


b.

Install the 2 transmission revolution sensors to the automatic transmission case sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 82.INSTALL OIL COOLER TUBE UNION

a.

Coat 2 new O-rings with ATF, and install the 2 oil cooler tube unions.


b.
C263936

Install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 84540 83.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.

Clean the bolt and the bolt hole.


b.
A057108E68
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.375,0.323 0.177,0.167 10 false *1

Apply adhesive to 2 or 3 threads on the end of the bolt.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C263925

Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.


d.

Install a new lock washer and the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


e.
C263944E01
1.791,0 1.915,0.161 0.125,0.161 10 N

Turn the transmission control shaft lever RH counterclockwise until it stops, and turn it clockwise 2 notches to set it to the N position.


f.
U118093E19
1.969,0.896 2.813,0.896 true 1.99,1.563 2.802,1.563 true 1.969,0.563 1.969,1.188 false 2.833,0.802 3,0.958 0.167,0.156 10 false *a 2.833,1.458 3,1.615 0.167,0.156 10 false *b

Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.

Text in Illustration
*a Neutral Basic Line
*b Groove

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


g.
D027990

Using a screwdriver, bend the tabs of the lock washer.


Hide 35572 84.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH

a.
C263924

Install the transmission control shaft lever RH to the park/ neutral position switch assembly with the spring washer and nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 35015S 85.INSTALL REFILL PLUG

a.

Coat a new O-ring with ATF, and install it to the refill plug.


b.

Install the refill plug.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)