Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM U

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS on.


f.

Enter the following menus: "Powertrain / ECT / Data List" or "Body Electrical / Main Body / Data List".


g.

According to the display on the GTS, read the "Data List".

"Powertrain / ECT / Data List"
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed /
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed /
Min.: 0 rpm, Max.: 16383.75 rpm
550 to 800 rpm: Idling -
Coolant Temp Engine coolant temperature /
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
·

If value -40°C (-40°F): sensor circuit open

·

If value 215°C (419°F): sensor circuit shorted


Engine Run Time Engine run time /
Min.: 0 second,
Max.: 65535 seconds
Time after engine start -
Battery Voltage Battery voltage /
Min.: 0, Max.: 65.535 V
11 to 14 V: Idling -
Stop Light Switch Stop light switch status/
ON or OFF
Brake pedal is
·

ON: Depressed

·

OFF: Released


-
A/C signal A/C signal status /
ON or OFF
A/C switch is:
ON : OFF
-
#Codes (Include History) # of Codes /
Min.: 0, Max.: 255
- Number of detected DTCs
MIL ON Run Distance MIL ON run distance /
Min.: 0 km (0 mile),
Max.: 65535 km (40723 mile)
Distance after DTC detected -
Running Time from MIL ON Running time from MIL ON /
Min.: 0 minute,
Max.: 65535 minutes
Equivalent to running time after MIL ON -
Time after DTC Cleared Time after DTC cleared /
Min.: 0 minute,
Max.: 65535 minutes
Equivalent to time after DTCs cleared -
Distance from DTC Cleared Distance after DTC cleared /
Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Equivalent to time after DTCs cleared -
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared /
Min.: 0, Max.: 255
- Number of warm-up cycles after DTCs cleared
TC and TE1 TC and TE1 terminals of DLC3 /
ON or OFF
- Active Test support data
Engine Speed from EFI Engine speed /
Min.: 0 rpm, Max.: 16383.75 rpm
550 to 800 rpm: Idling -
Coolant Temp from EFI Engine coolant temperature /
Min.: -40°C (-40°F), Max.: 215°C (419°F)
80 to 105°C (176 to 221°F): After warming up
·

If value -40°C (-40°F): sensor circuit open

·

If value 140°C (284°F): sensor circuit shorted


Throttle Position from EFI Throttle sensor position /
Min.: 0%, Max.: 100%
·

0%: Accelerator pedal released

·

64 to 96%: Accelerator pedal fully depressed


Recognition value for throttle opening angle on TCM
Accel Position from EFI Absolute Accelerator Pedal Position /
Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal released

·

54 to 86%: Accelerator pedal fully depressed


-
Received MIL from ECT MIL request status/
ON : OFF
MIL request is:
ON : OFF
-
Shift Position Sig from ECT Received Shift Position Signal from ECT
1st,2nd,3rd,4th,5th,6th,7th,8th
Shift lever position is
·

On D: 1st, 2nd, 3rd, 4th, 5th or 6th

·

On M: 1st, 2nd, 3rd, 4th, 5th or 6th


-
SPD(NT) Input shaft speed/
Min.: 0 rpm
Max.: 12,750 rpm
Lock-up is
·

ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

·

OFF (idling with shift lever on N): Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm
SPD(SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) -
Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever is:
·

On P: ON

·

Not on P: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever is:
·

On R: ON

·

Not on R: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever is:
·

On N: ON

·

Not on N: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Sport Shift Up SW Sport shift up switch status/
ON or OFF
·

Continuously shift to "+" (upshift): ON

·

Release "+" (up-shift): OFF


-
Sport Shift Down SW Sport shift down switch status/
ON or OFF
·

Continuously shift to "-" (down-shift): ON

·

Release "-" (down-shift): OFF


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
Shift lever position is:
·

M, "+" and "-": ON

·

Not on M, "+" and "-": OFF


-
Snow Switch Status Pattern switch (ECT SNOW) status/
ON or OFF
Ignition switch is:
Pushed: OFF
↓
Pattern select switch (ECT SNOW) is:
Pushed: ON
↓
Pattern select switch (ECT SNOW) is:
Pushed: OFF
-
Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever is:
·

On D or M: ON

·

Not on D or M: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
A/T Oil Temperature 1 ATF temperature sensor No. 1 value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test: 50 to 100°C (122 to 212°F)

·

Equal to ambient temperature while engine is cold


If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor No. 1 circuit is opened or short circuited
Lock Up Lock Up Status/
ON or OFF
Lock-up is
·

Operating: ON

·

Not operating: OFF


-
SL Solenoid Status Shift solenoid SL status/
ON or OFF
Shift solenoid SL is
·

Operating: ON

·

Not operating: OFF


-
Shift Status TCM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Shift lever position is
·

On D: 1st, 2nd, 3rd, 4th, 5th or 6th

·

On M: 1st, 2nd, 3rd, 4th, 5th or 6th


-
MT Down Shift Indication Shift indicator lamp down shift status/
ON or OFF
Shift indicator lamp is:
ON : OFF
-
MT Up Shift Indication Shift indicator lamp up shift status/
ON or OFF
Shift indicator lamp is:
ON : OFF
-
Snow or 2nd Mode Pattern select switch (SNOW) status/
ON or OFF
Ignition switch is:
ON : OFF
↓
Pattern select switch is:
Pushed : ON
↓
Pattern select switch is:
Released : OFF
-

"Powertrain / ECT / Data List"
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
Brake pedal is
·

ON: Depressed

·

OFF: Released


-
Shift P Signal PNP switch status/
ON or OFF
Shift lever is:
·

On P: ON

·

Not on P: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
IG Power Supply Voltage IG Power Supply Voltage /
Min.: 0, Max.: 21.4 V
11 to 14 V: Idling -
Shift Lock Solenoid Shift Lock Control Unit Assembly status/
ON or OFF
Shift Lock Control Unit Assembly is
·

Operating: ON

·

Not operating: OFF


-



ACTIVE TEST


HINT:

Using GTS to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS on.


f.

Enter the following menus: "Powertrain / ECT / Active Test" or "Body Electrical / Main Body / Active Test".


g.

According to the display on the GTS, perform the "Active Test".

"Powertrain / ECT / Active Test"
Tester Display Test Part Control Range Diagnostic Note
Activate the Solenoid (SLU) Operate the shift solenoid SLU ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Solenoid (S1) Operate the shift solenoid S1 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Solenoid (S2) Operate the shift solenoid S2 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Solenoid (S3) Operate the shift solenoid S3 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Solenoid (S4) Operate the shift solenoid S4 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Lock Up Control shift solenoid SLU to set automatic transmission to lock-up condition ON or OFF Possible to check shift solenoid valve SLU operation
[Vehicle Condition]
·

Throttle valve opening angle: Less than 35%

·

Vehicle speed: 50 km/h (30 mph) or more


Control the Shift Position Operate shift solenoid valve and set each shift position by yourself
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less
Activate the Solenoid (SR) Operate the shift solenoid SR ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Solenoid (SL1) Operate the shift solenoid SL1 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Activate the Solenoid (SL2) Operate the shift solenoid SL2 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever P or N position


Connect the TC and TE1 Connects and disconnects TC and TE1.
(transitions into the fluid temperature detection mode)
ON or OFF The MIL will not blink when "Connect the TC and TE1 / ON" is selected.

"Body Electrical / Main Body / Active Test"
Tester Display Test Part Control Range Diagnostic Note
Shift Lock Operate the shift lock ON or OFF -

*: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST) as well.

HINT:

The pressure values in Active Test and HYDRAULIC TEST are different from each other.