Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM U

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE CHART


This function minimizes the loss of the ECT functions when any malfunction occurs in each sensor or solenoid.

Malfunction Part Function
DTC P0717:
Input Speed Sensor NT
During an input speed sensor malfunction, shift control is effected through the output speed sensor signal SP2.
During an input speed sensor malfunction, up-shift to the 5th and 6th, AI-SHIFT*1 and flex lock-up clutch control are prohibited.
DTC P0722:
Output Speed Sensor SP2
During an output speed sensor malfunction, shift control is effected through the input speed sensor signal NT.
During an output speed sensor malfunction, up-shift to the 5th and 6th, AI-SHIFT*1 and flex lock-up clutch control are prohibited.
DTC P0711, P0712, P0713:
ATF Temperature Sensor
During an ATF temperature sensor malfunction, up-shift to the 5th and 6th and flex lock-up clutch control are prohibited.
Shift Solenoid Valve S1, S2, S3, S4 and SR If the solenoid valve system is open or shorted, the TCM cuts power to all solenoids, leaving just the mechanical hydraulic circuit, requiring manual shifting (fixed to 4th).
DTC P0776, P0961, P0962, P0963, P0965, P0966, P0967:
Shift Solenoid Valve SL1 and SL2
During a solenoid valve SL1 or SL2 malfunction, up-shift to the 5th and 6th and flex lock-up clutch control are prohibited.
DTC P2757, P2758, P2762, P2763, P2764:
Shift Solenoid Valve SLU
During a solenoid valve SLU malfunction, the current to the solenoid valve is stopped. This stops lock-up control and flex lock-up control, fuel economy decreases.
DTC P2714, P2719, P2720, P2721:
Shift Solenoid Valve SLT
During a solenoid valve SLT malfunction, the current to the solenoid valve is stopped. This stops line pressure optimal control, the shift shock increases. However, shifting is effected through normal clutch pressure control.

*: AI (Artificial Intelligence) -SHIFT control

In addition to the switching of the shift pattern through the pattern select switch, the AI-SHIFT control enables the ECM to estimate the road conditions and the driver's intention in order to automatically select the optimal shift pattern. As a result, a comfortable ride has been realized.

a.

Fail-safe operation for electronically malfunctioning shift solenoid valve (S1, S2, S3, S4 and SR):

HINT:

Fail-safe operation in the event of an electric system malfunction.

Fail safe function:

If either of the shift solenoid valve circuits has an open or short failure, the ECM turns the other shift solenoid "ON" and "OFF" in order to shift into the gear positions shown in the table below.

In case of a short circuit, the ECM stops sending current to the short circuited solenoid.

Even if staring the engine again in the fail-safe mode, the gear position remains in the same position.


Operating Condition of Shift Solenoid Valves
Shift Lever Position or Shift Range Gear Position Shift Solenoid Valve
S1 S2 S3 S4 SR SL1 SL2 SLU
P Park Off On On On On Off On Off
R* Reverse Off On On On On On On Off
N Neutral Off On On On On On On Off
D, M6 1st Off On On Off On Off On Off
2nd On On On On On Off Off On
3rd On Off On Off On Off Off On
4th* On Off Off Off On Off On On
5th* On Off Off On Off On Off On
6th* On On Off On Off On Off On
M5 1st Off On On Off On Off On Off
2nd On On On On On Off Off On
3rd On Off On Off On Off Off On
4th* On Off Off Off On Off On On
5th* On Off Off On Off On Off On
M4 1st Off On On Off On Off On Off
2nd On On On On On Off Off On
3rd On Off On Off On Off Off On
4th* On Off Off Off On Off On On
M3 1st Off On On Off On Off On Off
2nd On On On On On Off Off Off
3rd* On Off On Off On Off Off Off
M2 1st Off On On Off On Off On On
2nd* On On On On On Off Off Off
M1 1st* Off On On Off On Off Off Off

HINT:

*: Engine braking occurs



b.

Fail-safe operation for mechanically malfunction:

HINT:

Fail-safe operation in the event of a mechanical system malfunction.

Fail safe function:

The ECM controls the gear position as shown in the table below when malfunctions occur.


Fail-safe chart for mechanical malfunction:
DTC Condition Gear*1
- Normal 1st 2nd 3rd 4th 5th 6th
P0751 Shift solenoid valve S1:
Stuck OFF malfunction
1st*2 2nd ↑ 3rd 3rd 3rd
P0762 Shift solenoid S3:
Stuck ON malfunction
1st 2nd ↑ 3rd 3rd 3rd
P0766 Shift solenoid valve S4, Shift solenoid valve SL2 or Valve body (Brake control valve):
Malfunction
1st 2nd ↑ 3rd 3rd 3rd
P0781 Valve body (1-2 shift valve):
Malfunction
1st*2 2nd ↑ 3rd 3rd 3rd
P0729 Valve body (Sequence valve):
Malfunction
1st 2nd ↑ 4th 5th 5th

HINT:
·

*1: Actual gear shift (gear position) under fail-safe operation

·

*2: Under engine braking, downshifting to 1st or 2nd gear is prohibited.