Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for RHD)
RM2090E _52 Drivetrain _060675 CLUTCH _0297561 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31301S 2.INSTALL NO. 2 CLUTCH PEDAL CUSHION

a.

Install the No. 2 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31301B 3.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.

Install the 2 No. 1 clutch pedal cushions to the clutch pedal sub-assembly.


Hide 31453B 4.INSTALL BUSH

a.

Install the 3 bushes to the clutch pedal support sub-assembly and the clutch pedal sub-assembly.


Hide 31324A 5.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C261053

Apply MP grease to the 2 clutch pedal bushes.

Text in Illustration
V100135

MP grease


b.

Install the 2 clutch pedal bushes and the clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and the nut.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Turn the nut while holding the bolt.


HINT:

Install the bolt from the left side of the vehicle.



Hide 31301A 7.INSTALL CLUTCH PEDAL SPRING

a.
C261054

Apply MP grease to assist rod A, assist rod B and clutch pedal spring.

Text in Illustration
V100135

MP grease


b.

Install the assist rod A, assist rod B, clutch pedal spring and assist bush to the clutch pedal sub-assembly and the clutch pedal support sub-assembly.


c.
C261055

Apply MP grease to 2 clevis pins.

Text in Illustration
V100135

MP grease


d.

Install the 2 E-ring and the 2 clevis pins.


Hide 88280A 8.INSTALL CLUTCH SWITCH ASSEMBLY

a.

Install the clutch switch assembly to the clutch pedal support sub-assembly with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 84520 9.INSTALL CLUTCH START SWITCH ASSEMBLY

a.

Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the clamp.


Hide 55107A 10.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.

Install the clutch pedal support sub-assembly to the vehicle with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Apply MP grease to the new clevis pin.


c.

Install the clutch master cylinder push rod clevis to the clutch pedal sub-assembly with the clevis pin and a clip.

HINT:

Install the clevis pin from the right side of the vehicle.



d.

Connect the 2 connectors.


Hide 11.INSPECT AND ADJUST CLUTCH PEDAL

Hide 88280A 12.INSPECT CLUTCH SWITCH ASSEMBLY

a.
C263919E01
2.617,1.636 2.783,1.800 0.166,0.164 10 *a

Without depressing the clutch pedal, check that there is no clearance between the switch shaft and the clutch pedal stopper.

Text in Illustration
*a No Clearance


Hide 73900 13.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL