Home › Drivetrain › CLUTCH › CLUTCH UNIT
RM2090E _52 Drivetrain _060675 CLUTCH _0297565 CLUTCH UNIT G

CLUTCH  CLUTCH UNIT  INSPECTION  


PROCEDURE

Hide 31250 1.INSPECT CLUTCH DISC ASSEMBLY

a.
C258510

Using a vernier caliper, measure the rivet head depth.

Minimum rivet depth:

0.3 mm (0.0118 in.)


If necessary, replace the clutch disc assembly.


b.
C258511

Install the clutch disc assembly to the manual transmission assembly.

NOTICE:

Insert the clutch disc assembly in the correct direction.



c.

Using a dial indicator with a roller instrument, measure the clutch disc assembly runout.

Maximum runout:

0.8 mm (0.0315 in.)


If necessary, replace the clutch disc assembly.


Hide 31210 2.INSPECT CLUTCH COVER ASSEMBLY

a.
C258512E01
2.136,0.632 2.264,0.793 0.128,0.162 10 A 2.836,0.391 2.965,0.553 0.128,0.162 10 B

Using a vernier caliper, measure the depth and width of the diaphragm spring wear.

Maximum:
A (Depth):

0.5 mm (0.0197 in.)

B (Width):

6.0 mm (0.236 in.)


If necessary, replace the clutch cover assembly.


Hide 13405 3.INSPECT FLYWHEEL SUB-ASSEMBLY

a.
C258513

Using a dial indicator, measure the flywheel sub-assembly runout.

Maximum runout:

0.1 mm (0.00394 in.)


If necessary, replace the flywheel sub-assembly.


Hide 31230 4.INSPECT CLUTCH RELEASE BEARING ASSEMBLY

a.
C127507

Check that the clutch release bearing assembly moves smoothly without abnormal resistance by turning the sliding parts of the clutch release bearing assembly (contact surfaces with the clutch cover) while applying force in the axial direction.


b.

Inspect the clutch release bearing assembly for damage and wear.

If necessary, replace the clutch release bearing assembly.


Hide 13405G 5.INSPECT FLYWHEEL BEARING

a.
C299420

Turn the flywheel bearing by hand while applying rotational force and check that the flywheel bearing rotates smoothly. If the flywheel bearing sticks or a considerable amount of resistance is felt, replace the flywheel bearing.

HINT:

The flywheel bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 13405G 6.REPLACE FLYWHEEL BEARING

a.
A276036E06
1.365,1.688 1.021,1.688 false 0.698,1.604 1,1.781 0.302,0.177 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


b.
C299423

Remove any 2 diametrically opposite bolts.


c.
C299421E03
2.021,0.479 2.25,0.25 false 1.375,2.104 1.635,2.26 true 2.281,0.125 2.594,0.292 0.313,0.167 10 false SST 1.083,1.99 1.396,2.156 0.313,0.167 10 true SST 1.458,3.146 1.615,3.333 0.156,0.188 10 false *a 2.5,3.01 2.656,3.198 0.156,0.188 10 false *b

Using SST, remove the flywheel bearing.

SST
09303-35011  

Text in Illustration
*a Hold
*b Turn


d.
C299422E03
1.677,0.552 1.427,0.75 false 1.917,1.271 1.917,0.969 false 1.604,2.563 1.458,2.854 1.458,2.854 1.74,2.542 true 1.521,0.156 1.708,0.344 0.188,0.188 10 false *a 1.781,1.292 2.073,1.448 0.292,0.156 10 false SST 1.698,0.406 2,0.573 0.302,0.167 10 false SST 1.156,2.844 1.5,3.021 0.344,0.177 10 true SST

Using SST and a hammer, tap in a new flywheel bearing.

SST
09950-60010  (09951-00340)
09950-70010  (09951-07150)

Standard depth:

0 to 0.4 mm (0 to 0.0158 in.)


Text in Illustration
*a Depth from flywheel edge

NOTICE:
·

Do not tap in the flywheel bearing at an angle.

·

Do not tap in the flywheel bearing more than necessary.



HINT:

After installing the flywheel bearing, make sure that it rotates smoothly.



e.
A276036E06
1.365,1.688 1.021,1.688 false 0.698,1.604 1,1.781 0.302,0.177 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


f.
C299423

Install the 2 bolts.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)