Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297574 MANUAL TRANSAXLE UNIT G

TL70 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT NO. 1 GEAR SHIFT HEAD

a.
C257302

Using a vernier caliper, measure the clearance of the No. 1 gear shift head groove.

Standard clearance:

15.2 to 15.4 mm (0.59843 to 0.60630 in.)


Maximum clearance:

15.4 mm (0.60630 in.)


HINT:

If the clearance exceeds the maximum, replace the No. 1 gear shift head with a new one.



Hide 2.INSPECT NO. 2 GEAR SHIFT HEAD

a.
C257303

Using a vernier caliper, measure the clearance of the No. 2 gear shift head groove.

Standard clearance:

15.2 to 15.4 mm (0.59843 to 0.60630 in.)


Maximum clearance:

15.4 mm (0.60630 in.)


HINT:

If the clearance exceeds the maximum, replace the No. 2 gear shift head with a new one.



Hide 3.INSPECT NO. 3 GEAR SHIFT HEAD

a.
C257304

Using a vernier caliper, measure the clearance of the No. 3 gear shift head groove.

Standard clearance:

15.2 to 15.4 mm (0.598 to 0.606 in.)


Maximum clearance:

15.4 mm (0.606 in.)


HINT:

If the clearance exceeds the maximum, replace the No. 3 gear shift head with a new one.



Hide 4.INSPECT SHIFT SHAFT

a.
C257305

Using a vernier caliper, measure the claw width of the shift shaft.

Standard width:

14.8 to 15.0 mm (0.583 to 0.591 in.)


Minimum width:

14.8 mm (0.583 in.)


HINT:

If the width is less than the minimum, replace the gear shift with a new one.



Hide 5.INSPECT NO. 1 SHIFT INTER LOCK BLOCK

a.
C258815

Using a vernier caliper, measure the claw width of the No. 1 shift inter lock block.

Standard width:

14.8 to 15.0 mm (0.583 to 0.591 in.)


Minimum width:

14.8 mm (0.583 in.)


HINT:

If the width is less than the minimum, replace the No. 1 shift inter lock block.



Hide 6.INSPECT NO. 4 GEAR SHIFT FORK

a.
C257307

Using a vernier caliper, measure the clearance of the No. 4 gear shift fork groove.

Standard clearance:

15.2 to 15.4 mm (0.598 to 0.606 in.)


Maximum clearance:

15.4 mm (0.606 in.)


HINT:

If the clearance exceeds the maximum, replace the No. 4 gear shift fork with a new one.



Hide 7.INSPECT 5TH SHIFT HEAD

a.
C259359

Using a vernier caliper, measure the clearance of the 5th shift head groove.

Standard clearance:

15.2 to 15.4 mm (0.598 to 0.606 in.)


Maximum clearance:

15.4 mm (0.606 in.)


HINT:

If the clearance exceeds the maximum, replace the 5th shift head with a new one.



Hide 8.INSPECT NO. 2 SYNCHRONIZER RING

a.
C257043

Apply manual transmission gear oil to the taper cone of the counter shaft 6th gear, and then hold the No. 2 synchronizer ring in position with your hand to measure the clearance between the No. 2 synchronizer ring and counter shaft 6th gear by using a feeler gauge.

Standard clearance:

0.88 to 1.52 mm (0.0346 to 0.0598 in.)


Minimum clearance:

0.88 mm (0.0346 in.)


NOTICE:

Check the entire circumference of the gear.


HINT:

If the clearance is less than the minimum, replace the No. 2 synchronizer ring and counter shaft 6th gear with a new one.



b.
C257044

Apply manual transmission gear oil to the taper cone of the counter shaft 6th gear, and then hold the No. 2 synchronizer ring in position with your hand to check that it does not slide in the circumferential direction.

HINT:

If the No. 2 synchronizer ring slides, replace the No. 2 synchronizer ring and counter shaft 6th gear with a new one.



Hide 9.INSPECT COUNTER SHAFT 6TH GEAR

a.
C257045

Using a cylinder gauge, measure the inside diameter of the counter shaft 6th gear.

Standard inside diameter:

34.015 to 34.040 mm (1.33917 to 1.34016 in.)


Maximum inside diameter:

34.040 mm (1.34016 in.)


HINT:

If the inside diameter exceeds the maximum, replace the counter shaft 6th gear with a new one.



Hide 10.INSPECT NO. 4 TRANSMISSION HUB SLEEVE

a.
C257046

Check that the spline gear edges of the No. 4 transmission hub sleeve are not worn down.

HINT:

If it shows any sign of wear, replace the No. 4 transmission hub sleeve with a new one.



b.

Install the No. 4 transmission hub sleeve to the No. 4 transmission clutch hub, and then check that it slides smoothly.

HINT:

If it does not slide smoothly, replace the No. 4 transmission hub sleeve and No. 4 transmission clutch hub with a new one.



Hide 11.INSPECT NO. 4 TRANSMISSION HUB SLEEVE CLEARANCE

a.
C257047

Using a vernier caliper, measure the claw width of the No. 4 gear shift fork.

Standard width:

7.9 to 8.0 mm (0.311 to 0.315 in.)


Minimum width:

7.9 mm (0.311 in.)


HINT:

If the width is less than the minimum, replace the gear No. 4 shift fork with a new one.



b.

Using a vernier caliper, measure the groove of the No. 4 transmission hub sleeve and then calculate the clearance with the No. 4 gear shift fork.

Standard clearance:

0.15 to 0.35 mm (0.00590 to 0.0138 in.)


Maximum clearance:

0.35 mm (0.0138 in.)


HINT:

If the clearance exceeds the maximum, replace both the No. 4 gear shift fork and No. 4 transmission hub sleeve with a new ones.



Hide 12.INSPECT REVERSE IDLER GEAR

a.
C257112

Using a cylinder gauge, measure the inner diameter of the reverse idler gear.

Standard inside diameter:

22.040 to 22.061mm (0.86771 to 0.86854 in.)


Maximum inside diameter:

22.061mm (0.86854 in.)


HINT:

If the inside diameter exceeds the maximum, replace the reverse idler gear with a new one.



Hide 13.INSPECT REVERSE IDLER GEAR SHAFT

a.
C257113

Using a micrometer, measure the outer diameter of the reverse idler gear shaft.

Standard outer diameter:

21.979 to 22.000 mm (0.86531 to 0.86614 in.)


Minimum outer diameter:

21.979 mm (0.86531 in.)


HINT:

If the outer diameter is less than the minimum, replace the reverse idler gear shaft with a new one.