Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297574 MANUAL TRANSAXLE UNIT A

TL70 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C257296

Remove the manual transmission filler plug and gasket.


Hide 2.REMOVE MANUAL TRANSMISSION DRAIN PLUG

a.
C257297

Remove the manual transmission drain plug and gasket.


Hide 31236B 3.REMOVE RELEASE FORK SUPPORT

a.
C258508

Using a 19 mm deep socket wrench, remove the release fork support from the clutch housing.


Hide 84210 4.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C266432

Disengage the 3 clamps.


b.
C257023

Using a 19 mm union nut wrench, remove the back-up light switch assembly and gasket.


Hide 5.REMOVE NEUTRAL POSITION SWITCH ASSEMBLY

a.
C257024

Disengage the clamp.


b.
C257025

Using a 19 mm union nut wrench, remove the neutral position switch assembly and gasket.


Hide 6.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C257298

Remove the bolt and wire harness clamp bracket.


Hide 7.REMOVE LOCK BALL PIN

a.
C257027

Using a 10 mm hexagon socket wrench, remove the head straight screw plug, compression spring and lock ball pin.


Hide 8.REMOVE HOLDER

a.
C257028

Using a 27 mm deep socket wrench, remove the holder, compression spring and lock ball pin.


Hide 9.REMOVE TRANSMISSION EXTENSION HOUSING SUB-ASSEMBLY

a.
C257029

Remove the bolt.


b.
C257030E01
0.945,1.199 0.753,1.475 false 0.578,1.496 0.743,1.651 0.165,0.156 10 *1

Remove the 8 bolts and clamp.

Text in Illustration
*1 Clamp


c.
C257031

Using a plastic hammer, remove the transmission extension housing sub-assembly.

NOTICE:
·

Be sure to remove the transmission extension housing sub-assembly while the transmission is in neutral.

·

Do not damage the transmission extension housing sub-assembly.




Hide 10.REMOVE EXTENSION HOUSING REAR OIL SEAL

a.
C257033E02
1.969,1.24 2.146,0.698 true 2.115,0.5 2.26,0.656 0.146,0.156 10 false *1

Using a screwdriver with its tip wrapped with protective tape, remove the extension housing rear oil seal.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not damage the transmission extension housing sub-assembly.


HINT:

Remove the transmission extension housing sub-assembly while protecting it with a piece of cloth.



Hide 11.REMOVE EXTENSION HOUSING DUST DEFLECTOR

a.
C257039

Using a plastic hammer, remove the extension housing dust deflector.


Hide 12.REMOVE TRANSMISSION EXTENSION HOUSING OIL SEAL

a.
C257299E02
1.75,0.417 2.198,0.104 true 2.25,0.021 2.406,0.167 0.156,0.146 10 false *1

Using a screwdriver with its tip wrapped with protective tape, remove the transmission extension housing oil seal.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not damage the transmission extension housing sub-assembly.


HINT:

Remove the transmission extension housing sub-assembly while protecting it with a piece of cloth.



Hide 13.REMOVE NO. 2 EXTENSION HOUSING OIL RECEIVER PIPE

a.
C257034

Remove the No. 2 extension housing oil receiver pipe.


Hide 14.REMOVE NO. 1 EXTENSION HOUSING OIL RECEIVER PIPE

a.
C257036

Remove the bolt, No. 1 extension housing oil receiver pipe and stopper plate.


b.
C257037

Remove the straight pin.


Hide 15.REMOVE SHIFT SHAFT

a.
C257328

Slide and remove the shift shaft and No. 1 shift inter lock block.


Hide 16.REMOVE NO. 1 SHIFT INTER LOCK BLOCK

a.
C262543

Remove the No. 1 shift inter lock block from the shift shaft.


Hide 17.REMOVE FRONT SHIFT INNER LEVER

a.
C257329

Remove the bolt and front shift inner lever from the shift shaft.


Hide 18.REMOVE HEAD STRAIGHT SCREW PLUG

a.
C257294

Using a T40 "TORX" socket wrench, remove 3 head straight screw plugs.


b.
C257295

Using a magnet hand, remove the 2 compression springs and 2 balls.


Hide 19.REMOVE SHIFT ARM

a.
C257330

Using a screwdriver, remove the E-ring.

NOTICE:

Use a cloth to prevent the E-ring from flying off.



b.
C257331

Remove the shift arm.


Hide 20.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C266546

Remove the No. 3 gear shift fork shaft and 5th shift head together.

NOTICE:
·

Be careful not to drop the ball from the 5th shift head.

·

The ball on the transmission case may fall inside the transmission case. If that happens, take it out when the transmission case is removed.




b.

Remove the ball from the 5th shift head.


c.
C257335

Using a magnetic hand, remove the ball.


Hide 21.REMOVE 5TH SHIFT HEAD

a.
C266544

Using 2 screwdrivers and a plastic hammer, remove the shaft snap ring.

NOTICE:

Use a cloth to prevent the shaft snap ring from flying off.



b.
C266545

Remove the washer.


c.
C257336

Remove the 5th shift head, compression spring and ball.

NOTICE:

Be careful of the ball and compression spring that fall out when sliding the 5th shift head.



Hide 22.INSPECT COUNTER SHAFT 6TH GEAR THRUST CLEARANCE

a.
C257300E02
2.729,0.635 1.979,1.25 true 2.771,0.552 3.063,0.854 0.292,0.302 10 false SST

Using SST and a dial indicator, measure the thrust clearance.

SST
09350-20015  (09350-06120)

Standard clearance:

0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum clearance:

0.40 mm (0.0157 in.)


HINT:

If the clearance exceeds the maximum, replace the counter shaft 6th gear, No. 4 transmission clutch hub, 6th gear thrust washer, needle roller bearing and counter shaft with a new ones.



Hide 23.INSPECT COUNTER SHAFT 6TH GEAR RADIAL CLEARANCE

a.
C257301

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.015 to 0.068 mm (0.000590 to 0.00268 in.)


Maximum clearance:

0.068 mm (0.00268 in.)


HINT:

If the clearance exceeds the maximum, replace the counter shaft 6th gear, needle roller bearing and counter shaft with a new ones.



Hide 24.REMOVE NO. 4 TRANSMISSION CLUTCH HUB

a.
C257337

Using 2 screwdrivers and a plastic hammer, remove the shaft snap ring.

NOTICE:

Use a cloth to prevent the shaft snap ring from flying off.



b.
C257338E02
1.896,0.698 2.698,1.25 2.698,1.25 2.031,1.188 true 2.708,1.25 1.865,1.49 true 2.656,0.74 2.823,0.896 0.167,0.156 10 false *b 0.76,1.51 0.927,1.677 0.167,0.167 10 false *a 2.781,1.188 3.083,1.583 0.302,0.396 10 false SST

Using SST and 3 bolts, remove the No. 4 transmission clutch hub, No.4 transmission hub sleeve, No. 4 gear shift fork and No. 2 gear shift fork shaft all together.

Text in Illustration
*a Hold
*b Turn

SST
09950-30012  (09951-03010, 09953-03010, 09956-03010)


Hide 25.REMOVE NO. 4 GEAR SHIFT FORK

a.

for Pin:

i.
C257339

Using a 5 mm pin punch and hammer, remove the slotted spring pin.


ii.

Remove the No. 4 gear shift fork from the No. 2 gear shift fork shaft.



b.

for Bolt:

i.
C318110

Remove the bolt and No. 4 gear shift fork from the No. 2 gear shift fork shaft.



Hide 26.REMOVE NO. 4 TRANSMISSION HUB SLEEVE

a.
C257340

Using a screwdriver, remove the hole snap ring.


b.
C257070

Remove the No. 4 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the No. 4 transmission clutch hub.

NOTICE:
·

Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.

·

Do not deform the No. 1 synchromesh shifting key spring.



HINT:

During this operation, keep intact the No. 4 transmission clutch hub and No. 1 synchromesh shifting key.



Hide 27.REMOVE NO. 2 SYNCHRONIZER RING

a.
C257341

Remove the No. 2 synchronizer ring.


Hide 28.REMOVE COUNTER SHAFT 6TH GEAR

a.
C257342

Remove the counter shaft 6th gear.


Hide 29.REMOVE NEEDLE ROLLER BEARING

a.
C258418

Remove the needle roller bearing.


Hide 30.REMOVE 6TH GEAR THRUST WASHER

a.
C258419

Remove the 6th gear thrust washer.


b.
C258420

Remove the straight pin.


Hide 31.REMOVE NO. 2 GEAR SHIFT HEAD

a.
C258421

Using a 5 mm pin punch and hammer, remove the slotted spring pin.

NOTICE:
·

Use a cloth to prevent the slotted spring pin from flying off.

·

Take care in order that the slotted spring pin does not fall inside through the gear shift fork shaft hole.




b.

Remove the No. 2 gear shift head from the No. 2 gear shift fork shaft.


Hide 32.REMOVE NO. 1 GEAR SHIFT HEAD

a.
C258422

Using a 5 mm pin punch and a hammer, remove the slotted spring pin.

NOTICE:
·

Use a cloth to prevent the slotted spring pin from flying off.

·

Take care in order that the slotted spring pin does not fall inside through the gear shift fork shaft hole.




b.

Remove the No. 1 gear shift head from the No. 1 gear shift fork shaft.


Hide 33.REMOVE NO. 3 GEAR SHIFT HEAD

a.
C258423

Using a 5 mm pin punch and a hammer, remove the slotted spring pin.

NOTICE:
·

Use a cloth to prevent the slotted spring pin from flying off.

·

Take care in order that the slotted spring pin does not fall inside through the gear shift fork shaft hole.




b.

Remove the No. 3 gear shift head from the No. 3 gear shift fork shaft.


Hide 34.REMOVE REAR BEARING RETAINER

a.
C258424

Using a T45 "TORX" socket wrench, remove the 4 bolts and rear bearing retainer.


b.
C258425

Remove the shift arm pivot.


Hide 35.REMOVE TRANSMISSION CASE

a.
C258426

Using a snap ring expander, remove the shaft snap ring.


b.
C258427

Remove the bolt that retains the reverse idler gear shaft, and the gasket (transmission case side)


c.
C258428E01
1.262,1.357 0.853,1.464 false 0.65,1.387 0.813,1.556 0.163,0.170 10 *1

Remove the 9 bolts and clamp.

Text in Illustration
*1 Clamp


d.
C258429

Using a plastic hammer, remove the transmission case.

NOTICE:

Do not damage the transmission case.



Hide 36.REMOVE OIL RECEIVER PIPE

a.
C266428

Remove the oil receiver pipe.


Hide 37.REMOVE FRONT BEARING RETAINER

a.
C258431

Remove 7 bolts and front bearing retainer.


Hide 38.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

a.
C257040E02
1.729,1.01 1.854,0.385 true 1.792,0.208 1.948,0.365 0.156,0.156 10 false *1

Using a screwdriver with its tip wrapped with protective tape, remove the transmission front bearing retainer oil seal.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not damage the front bearing retainer.


HINT:

Remove the front bearing retainer while protecting it with a piece of cloth.



Hide 39.REMOVE COUNTER SHAFT

a.
C258432

Using a snap ring expander, remove the 2 shaft snap rings.

HINT:

Remove the 2 shaft snap rings from the input shaft and counter shaft.



b.
C258433

Remove the bolt and gasket to free the reverse idler gear and reverse idler gear shaft. (Clutch housing side)


c.
C258434

Using a hammer handle edge, tap to remove the input shaft, output shaft, counter shaft, reverse idler gear, reverse idler gear shaft, No. 1 gear shift fork shaft, No. 2 gear shift fork shaft and No. 3 gear shift fork shaft all together from the clutch housing side.


Hide 40.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C258435

Using 2 screwdrivers and a plastic hammer, remove the shaft snap ring.

NOTICE:

Use a cloth to prevent the shaft snap ring from flying off.



b.
C258436

Remove the bolt and No. 2 gear shift fork shaft.


Hide 41.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C258437

Using 2 screwdrivers and a plastic hammer, remove the shaft snap ring.

NOTICE:

Use a cloth to prevent the shaft snap ring from flying off.



b.
C258438

Remove the No. 1 gear shift fork shaft and No.1 gear shift fork together.


c.
C258439

Using 2 screwdrivers and a plastic hammer, remove the shaft snap ring.

NOTICE:

Use a cloth to prevent the shaft snap ring from flying off.



d.
C258440

Remove the bolt and No. 1 gear shift fork shaft.


Hide 42.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C260035

Remove the bolt and No. 3 gear shift fork shaft.


Hide 43.REMOVE INPUT SHAFT

a.
C258452

Remove the input shaft from the output shaft.


Hide 44.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

a.
C257110

Use a vice to secure the reverse idler gear, and then use a dial indicator to measure the radial clearance.

Standard clearance:

0.040 to 0.082 mm (0.00157 to 0.00323 in.)


Maximum clearance:

0.082 mm (0.00323 in.)


HINT:

If the clearance exceeds the maximum, replace the reverse idler gear and reverse idler gear shaft with a new ones.



Hide 45.REMOVE REVERSE IDLER GEAR SHAFT

a.
C257111

Remove the reverse idler gear shaft from the reverse idler gear.