Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297576 OUTPUT SHAFT G

TL70 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  INSPECTION  


PROCEDURE

Hide 1.INSPECT REAR OUTPUT SHAFT BEARING

a.
C257071

Check the rear output shaft bearing.

Standard:

Abnormal fitting, interfering, abnormal noise, or looseness should not be found.


HINT:

If any abnormality is found, replace the rear output shaft bearing with a new one.



Hide 2.INSPECT OUTPUT SHAFT

a.
C257074E02
1.844,1.51 1.99,1.698 0.146,0.188 10 false A 2.115,1.531 2.281,1.708 0.167,0.177 10 false B 2.74,1.531 2.896,1.698 0.156,0.167 10 false C

Using a micrometer, measure the outer diameter of each point.

Standard Outer Diameter:
Part Standard outer diameter mm (in.) Minimum outer diameter mm (in.)
A 31.984 to 32.000 (1.25921 to 1.25984) 31.984 (1.25921)
B 42.984 to 43.000 (1.69228 to 1.69291) 42.984 (1.69228)
C 40.984 to 41.000 (1.61354 to 1.61417) 40.984 (1.61354)


HINT:

If the outer diameter is less than minimum, replace the output shaft with a new one.



b.
C257075

Using V-blocks and a dial indicator, measure the runout of each location as shown in the illustration.

Standard runout:

0.03 mm (0.00118 in.) or less


HINT:

If the runout is outside the specification, replace the output shaft with a new one.



Hide 3.INSPECT REVERSE GEAR

a.
C257077

Using a cylinder gauge, measure the inner diameter of the reverse gear.

Standard inside diameter:

47.015 to 47.040 mm (1.85098 to 1.85197 in.)


Maximum inside diameter:

47.040 mm (1.85197 in.)


HINT:

If the inner diameter exceeds the maximum, replace the reverse gear with a new one.



Hide 4.INSPECT 1ST GEAR

a.
C257077

Using a cylinder gauge, measure the inside diameter of the 1st gear.

Standard inside diameter:

46.315 to 46.340 mm (1.82343 to 1.82441 in.)


Maximum inside diameter:

46.340 mm (1.82441 in.)


HINT:

If the inside diameter exceeds the maximum, replace the 1st gear with a new one.



Hide 5.INSPECT 2ND GEAR

a.
C257077

Using a cylinder gauge, measure the inside diameter of the 2nd gear.

Standard inside diameter:

49.015 to 49.040 mm (1.92972 to 1.93071 in.)


Maximum inside diameter:

49.040 mm (1.93071 in.)


HINT:

If the inside diameter exceeds the maximum, replace the 2nd gear with a new one.



Hide 6.INSPECT 1ST GEAR BEARING INNER RACE

a.
C257076

Using a micrometer, measure the outside diameter of the 1st gear bearing inner race.

Standard outer diameter:

40.284 to 40.300 mm (1.58598 to 1.58661 in.)


Minimum outer diameter:

40.284 mm (1.58598 in.)


HINT:

If the outside diameter is less than minimum, replace the 1st gear bearing inner race with a new one.



Hide 7.INSPECT NO. 1 TRANSMISSION HUB SLEEVE CLEARANCE

a.
C257047

Using a vernier caliper, measure the claw width of the No. 1 gear shift fork.

Standard width:

7.9 to 8.0 mm (0.311 to 0.315 in.)


Minimum width:

7.9 mm (0.311 in.)


HINT:

If the width is less than the minimum, replace the No. 1 gear shift fork with a new one.



b.

Using a vernier caliper, measure the groove of the No. 1 transmission hub sleeve, and then calculate the clearance with the No. 1 gear shift fork.

Standard clearance:

0.15 to 0.35 mm (0.00590 to 0.0138 in.)


Maximum clearance:

0.35 mm (0.0138 in.)


HINT:

If the clearance exceeds the maximum, replace both the No. 1 gear shift fork and No. 1 transmission hub sleeve with a new ones.



Hide 8.INSPECT NO. 3 TRANSMISSION HUB SLEEVE CLEARANCE

a.
C257047

Using a vernier caliper, measure the claw width of the No. 3 gear shift fork.

Standard width:

7.9 to 8.0 mm (0.311 to 0.315 in.)


Minimum width:

7.9 mm (0.311 in.)


HINT:

If the width is less than the minimum, replace the No. 3 gear shift fork with a new one.



b.

Using a vernier caliper, measure the groove of the No. 3 transmission hub sleeve, and then calculate the clearance with the No. 3 gear shift fork.

Standard clearance:

0.15 to 0.35 mm (0.00590 to 0.0138 in.)


Maximum clearance:

0.35 mm (0.0138 in.)


HINT:

If the clearance exceeds the maximum, replace both the No. 3 gear shift fork and No. 3 transmission hub sleeve with a new ones.



Hide 9.INSPECT NO. 1 TRANSMISSION HUB SLEEVE

a.
C257079

Check that the spline gear edges of the No. 1 transmission hub sleeve are not worn down.

HINT:

If it shows any sign of wear, replace the No. 1 transmission hub sleeve with a new one.



b.

Install the No. 1 transmission hub sleeve to the No. 1 transmission clutch hub, and then check that it slides smoothly.

HINT:

If it does not slide smoothly, replace the No. 1 transmission hub sleeve and No. 1 transmission clutch hub with a new one.



Hide 10.INSPECT NO. 3 TRANSMISSION HUB SLEEVE

a.
C257079

Check that the spline gear edges of the No. 3 transmission hub sleeve are not worn down.

HINT:

If it shows any sign of wear, replace the No. 3 transmission hub sleeve with a new one.



b.

Install the No. 3 transmission hub sleeve to the No. 3 transmission clutch hub, and then check that it slides smoothly.

HINT:

If it does not slide smoothly, replace the No. 3 transmission hub sleeve and No. 3 transmission clutch hub with a new one.



Hide 11.INSPECT NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

a.

Apply manual transmission gear oil to the taper cone of the 1st gear and No. 1 synchronizer ring set, and then hold the No. 1 synchronizer ring set in position with your hand to measure the clearance between the No. 1 synchronizer ring set and the 1st gear by using a feeler gauge.

C266880E02
0.906,0.073 1.115,0.292 0.208,0.219 10 false *a 3.25,0.052 3.458,0.271 0.208,0.219 10 false *b 5.531,0.052 5.74,0.271 0.208,0.219 10 false *c

Text in Illustration
*a Inner *b Middle
*c Outer - -

Standard Clearance:
Location Standard clearance mm ( in.)
Inner 0.48 to 1.12 (0.0189 to 0.0441)
Middle 0.38 to 1.22 (0.0150 to 0.0480)
Outer 0.8 to 1.8 (0.0315 to 0.0709)


NOTICE:

Check the entire circumference of the gear.


HINT:

If the result is not as specified, replace the No. 1 synchronizer ring set with a new one.



b.
C266881

Apply manual transmission gear oil to the taper cone of the 1st gear, and then hold the No. 1 synchronizer ring set in position with your hand to check that it does not slide in the circumferential direction.

HINT:

If the No. 1 synchronizer ring set slides, replace the No. 1 synchronizer ring set with a new one.



Hide 12.INSPECT NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

a.

Apply manual transmission gear oil to the taper cone of the 2nd gear and No. 1 synchronizer ring set, and then hold the No. 1 synchronizer ring set in position with your hand to measure the clearance between the No. 1 synchronizer ring set and the 2nd gear by using a feeler gauge.

C266880E02
0.906,0.073 1.115,0.292 0.208,0.219 10 false *a 3.25,0.052 3.458,0.271 0.208,0.219 10 false *b 5.531,0.052 5.74,0.271 0.208,0.219 10 false *c

Text in Illustration
*a Inner *b Middle
*c Outer - -

Standard Clearance:
Location Standard clearance mm ( in.)
Inner 0.48 to 1.12 (0.0189 to 0.0441)
Middle 0.38 to 1.22 (0.0150 to 0.0480)
Outer 0.8 to 1.8 (0.0315 to 0.0709)


NOTICE:

Check the entire circumference of the gear.


HINT:

If the result is not as specified, replace the No. 1 synchronizer ring set with a new one.



b.
C266881

Apply manual transmission gear oil to the taper cone of the 2nd gear, and then hold the No. 1 synchronizer ring in position with your hand to check that it does not slide in the circumferential direction.

HINT:

If the No. 1 synchronizer ring set slides, replace the No. 1 synchronizer ring set with a new one.