Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297576 OUTPUT SHAFT A

TL70 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT THRUST CLEARANCE

a.
C257060E01
0.751,1.809 0.927,1.975 0.176,0.165 10 *a 1.535,1.809 1.707,1.982 0.173,0.173 10 *b 2.29,1.809 2.484,1.960 0.194,0.151 10 *c

Using a feeler gauge, measure the thrust clearance of the 1st gear, 2nd gear and reverse gear.

Text in Illustration
*a Reverse gear thrust clearance
*b 2nd gear thrust clearance
*c 1st gear thrust clearance

Standard Clearance:
Gear Standard clearance mm (in.) Maximum clearance mm (in.)
1st gear 0.15 to 0.40 (0.00590 to 0.0157) 0.40 (0.0157)
2nd gear 0.10 to 0.45 (0.000394 to 0.0177) 0.45 (0.0177)
Reverse gear 0.10 to 0.45 (0.000394 to 0.0177) 0.45 (0.0177)


HINT:

If the clearance exceeds the maximum, replace the corresponding gear, transmission clutch hub, needle roller bearing and output shaft with a new ones.



Hide 2.INSPECT RADIAL CLEARANCE

a.
C257061E01
0.647,1.74 0.836,1.905 0.188,0.165 10 *a 1.667,1.712 1.864,1.882 0.196,0.171 10 *b 2.24,1.792 2.424,1.980 0.184,0.188 10 *c

Using a dial indicator, measure the radial clearance of the 1st gear, 2nd gear and reverse gear.

Text in Illustration
*a Reverse gear radial clearance
*b 2nd gear radial clearance
*c 1st gear radial clearance

Standard Clearance:
Gear Standard clearance mm (in.) Maximum clearance mm (in.)
1st gear 0.015 to 0.066 (0.000590 to 0.00260) 0.066 (0.00260)
2nd gear 0.015 to 0.066 (0.000590 to 0.00260) 0.066 (0.00260)
Reverse gear 0.015 to 0.066 (0.000590 to 0.00260) 0.066 (0.00260)


HINT:

If the clearance exceeds the maximum, replace the corresponding gear, needle roller bearing and output shaft with a new ones.



Hide 3.REMOVE REVERSE GEAR

a.
C257062

Using a snap ring expander, remove the shaft snap ring.


b.
C257063E02
2.042,1.365 2.333,0.792 2.333,0.792 1.667,0.729 true 1.656,0.938 2.323,0.802 true 2.385,0.698 2.74,0.896 0.354,0.198 10 false SST

Using SST and a press, remove the No. 3 transmission clutch hub, No. 3 transmission hub sleeve, reverse gear, No. 3 synchronizer ring and reverse gear bearing from the output shaft.

SST
09950-00020  
09950-60010  (09951-00230)
09950-70010  (09951-07100)


Hide 4.REMOVE NO. 3 TRANSMISSION HUB SLEEVE

a.
C257064

Remove the No. 3 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the No. 3 transmission clutch hub.

NOTICE:
·

Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.

·

Do not deform the No. 1 synchromesh shifting key spring.



HINT:

During this operation, keep intact the No. 3 transmission clutch hub and No. 1 synchromesh shifting key.



Hide 5.REMOVE 6TH GEAR

a.
C257065

Using 2 screwdrivers and a hammer, remove the shaft snap ring.


b.
C257066E02
1.938,1.115 2.25,0.813 true 2.302,0.688 2.594,0.844 0.292,0.156 10 false SST

Using SST and a press, remove the 6th gear.

SST
09950-00020  


Hide 6.REMOVE 1ST GEAR

a.
C266438E02
1.26,1.271 0.938,1.104 true 0.615,0.99 0.927,1.146 0.313,0.156 10 false SST

Using SST and a press, remove the rear output shaft bearing, 1st gear and 1st gear bearing inner race.

SST
09950-00020  


b.
C266439

Remove the 1st gear needle roller bearing, 1st shift restrict ball and No. 1 synchronizer ring set.


Hide 7.REMOVE 2ND GEAR

a.
C257069E02
1.375,1.396 1.01,1.156 false 1.375,1.396 1.01,1.156 true 0.667,1.031 0.958,1.208 0.292,0.177 10 false SST

Using SST and a press, remove the 2nd gear, No. 1 transmission clutch hub and 2nd gear needle roller bearing from the output shaft.

SST
09950-00020  


Hide 8.REMOVE NO. 1 SYNCHRONIZER RING SET

a.

Remove the No. 1 synchronizer ring set.


Hide 9.REMOVE NO. 1 TRANSMISSION HUB SLEEVE

a.
C257070

Remove the No. 1 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the No. 1 transmission clutch hub.

NOTICE:
·

Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.

·

Do not deform the No. 1 synchromesh shifting key spring.



HINT:

During this operation, keep the No. 1 transmission clutch hub and No. 1 synchromesh shifting key intact.