Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297576 OUTPUT SHAFT A

TL70 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL REVERSE GEAR

a.
C257082

Apply manual transmission gear oil to the mounting point of the output shaft, reverse gear bearing and inside surface and taper cone of the reverse gear.


b.

Install the reverse gear bearing and reverse gear to the output shaft.


Hide 2.INSTALL NO. 3 TRANSMISSION HUB SLEEVE

a.
C321947E02
2.823,1.865 2.823,2.083 true 2.51,2.323 2.51,2.573 true 2.927,2.448 3.104,2.604 true 2.167,0.302 2.313,0.302 false 1.208,0.396 1.406,0.396 false 1.01,0.271 1.219,0.438 0.208,0.167 10 false *1 1.958,0.188 2.167,0.354 0.208,0.167 10 false *2 2.74,1.677 2.948,1.844 0.208,0.167 10 false *3 2.427,2.573 2.635,2.74 0.208,0.167 10 false *4 3.031,2.604 3.24,2.771 0.208,0.167 10 false *5

Apply manual transmission gear oil to the moving parts of the No. 3 transmission clutch hub.

Text in Illustration
*1 No. 3 Transmission Clutch Hub
*2 No. 3 Transmission Hub Sleeve
*3 Ball
*4 No. 1 Synchromesh Shifting Key
*5 No. 1 Synchromesh Shifting Key Spring
V100135

Front Side


b.

As shown in the illustration, install the No. 3 transmission hub sleeve to the No. 3 transmission clutch hub. And install the 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs all together, and then install the 3 balls.

HINT:
·

Install the ball while holding down the No. 1 synchromesh shifting key spring.


·

After the installation, let the No. 1 synchromesh shifting key spring settle down.




Hide 3.INSTALL NO. 3 TRANSMISSION CLUTCH HUB

a.
C257083E01
1.848,0.712 2.157,0.712 false 2.171,0.62 2.462,0.783 0.290,0.163 10 SST

Install the No. 3 synchronizer ring to the reverse gear.


b.

Using SST and a press, install the No. 3 transmission clutch hub.

SST
09309-37010  

HINT:
·

Align the No. 3 transmission clutch hub and the No. 3 synchronizer ring so that they can fit together.

·

After the No. 3 transmission clutch hub is installed, check that the No. 3 synchronizer ring moves in the thrust direction.


·

Make sure to press fit the No. 3 transmission clutch hub until it touches the output shaft.




Hide 4.INSTALL SHAFT SNAP RING (for No. 3 transmission clutch hub)

a.
C257084

Select a shaft snap ring that is suitable to retain the specific thrust clearance between the No. 3 transmission clutch hub and shaft snap ring.

Standard clearance:

0 to 0.1 mm (0 to 0.00394 in.)


HINT:

Select the thickest shaft snap ring possible for installation.


Shaft Snap Ring Thickness
Part No. Thickness mm (in.) Mark
SU003-03581 1.80 (0.07086) A
SU003-03582 1.85 (0.07283) B
SU003-03583 1.90 (0.07480) C
SU003-03584 1.95 (0.07677) D
SU003-03585 2.00 (0.07874) E
SU003-03586 2.05 (0.08070) F


b.

Using a snap ring expander, install a new shaft snap ring to the output shaft.


Hide 5.INSTALL 2ND GEAR

a.
C257085

Apply manual transmission gear oil to the mounting point of the output shaft, 2nd gear needle roller bearing and inside surface and taper cone of the reverse gear.


b.

Install the 2nd gear needle roller bearing and 2nd gear to the output shaft.


Hide 6.INSTALL NO. 1 TRANSMISSION HUB SLEEVE

a.
C321945E02
2.823,1.885 2.823,2.104 true 2.51,2.323 2.51,2.573 true 2.927,2.448 3.104,2.604 false 2.177,0.25 2.323,0.25 false 1.333,0.313 1.531,0.313 false 1.135,0.198 1.344,0.365 0.208,0.167 10 false *1 1.969,0.135 2.177,0.302 0.208,0.167 10 false *2 2.74,1.677 2.948,1.844 0.208,0.167 10 false *3 2.427,2.573 2.635,2.74 0.208,0.167 10 false *4 3.021,2.604 3.229,2.771 0.208,0.167 10 false *5

Apply manual transmission gear oil to the moving parts of the No. 1 transmission clutch hub.

Text in Illustration
*1 No. 1 Transmission Clutch Hub
*2 No. 1 Transmission Hub Sleeve
*3 Ball
*4 No. 1 Synchromesh Shifting Key
*5 No. 1 Synchromesh Shifting Key Spring
V100135

Front Side


b.

As shown in the illustration, install the No. 1 transmission hub sleeve to the No. 1 transmission clutch hub. And install the 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs all together, and then install the 3 balls.

HINT:
·

Install the ball while holding down the No. 1 synchromesh shifting key spring.


·

After the installation, let the No. 1 synchromesh shifting key spring settle down.




Hide 7.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C266440

Align and install the No. 1 synchronizer ring set (for 2nd gear) in the position, as shown in the illustration.

HINT:
·

Align the middle ring claw with the groove in the 2nd gear.

·

Align the inner ring claw with the groove in the outer ring.




b.
C257087E02
1.708,1.094 2.198,1.115 2.198,1.115 1.75,1.5 true 2.271,1.031 2.594,1.198 0.323,0.167 10 false SST

Using SST and a press, install the No. 1 transmission clutch hub.

SST
09309-35010  
09631-12090  

HINT:
·

Align the No. 1 transmission clutch hub and the No. 1 synchronizer ring set (for 2nd gear) so that they can fit together.

·

After the No. 1 transmission clutch hub is installed, check that the No. 1 synchronizer ring set (for 2nd gear) moves in the thrust direction.


·

Make sure to press fit the No. 1 transmission clutch hub until it touches the output shaft.




c.
C257088

Align and install the No. 1 synchronizer ring set (for 1st gear) in the position, as shown in the illustration.

HINT:
·

Align the outer ring claw with the groove in No. 1 transmission clutch hub.

·

Align the inner ring claw with the groove in the outer ring.




Hide 8.INSTALL 1ST GEAR

a.
C257089E01
2.485,0.433 2.715,0.628 0.230,0.195 10 *1

After the output shaft is installed, apply manual transmission gear oil to the mounting point of the output shaft, needle roller bearing inner race, and inside surface and taper cone of the 1st gear.


b.

Install the 1st shift restrict ball, 1st gear, 1st gear needle roller bearing and 1st gear bearing inner race to the output shaft.

Text in Illustration
*1 1st Shift Restrict Ball

HINT:

Align the middle ring claw with the groove in the 1st gear.



Hide 9.INSTALL REAR OUTPUT SHAFT BEARING

a.
C266541E02
2.396,1.198 2.792,0.885 2.792,0.885 2.365,0.823 true 0.688,0.583 0.552,0.448 true 2.844,0.802 3.156,0.958 0.313,0.156 10 false SST 0.385,0.333 0.573,0.49 0.188,0.156 10 false *1

Using SST and a press, as shown in the illustration, install the rear output shaft bearing.

Text in Illustration
*1 Rear Output Shaft Bearing
V100135

Front Side

SST
09309-35010  
09316-60011  (09316-00021)

HINT:

Make sure to press fit the rear output shaft bearing until it touches the 1st gear bearing inner race.



Hide 10.INSTALL 6TH GEAR

a.
C257091E01
1.817,0.874 2.191,0.874 false 2.209,0.788 2.528,0.947 0.319,0.159 10 SST

Using SST and a press, install the 6th gear.

SST
09309-35010  

HINT:

Make sure to press fit the 6th gear until it touches the rear output shaft bearing.



Hide 11.INSTALL SHAFT SNAP RING (for 6th gear)

a.
C257092

Select a shaft snap ring that is suitable to retain the specific thrust clearance between the 6th gear and shaft snap ring.

Standard clearance:

0 to 0.11 mm (0 to 0.00433 in.)


HINT:

Select the thickest shaft snap ring possible for installation.


Shaft Snap Ring Thickness
Part No. Thickness mm (in.) Mark
SU003-03564 2.67 (0.10511) A
SU003-03565 2.73 (0.10748) B
SU003-03566 2.79 (0.10984) C
SU003-03567 2.85 (0.11220) D
SU003-03568 2.91 (0.11456) E
SU003-03569 2.97 (0.11692) F
SU003-03570 3.03 (0.11929) G
SU003-03571 3.09 (0.12165) H
SU003-03572 3.15 (0.12401) J
SU003-03573 3.21 (0.01053) K
SU003-03574 3.27 (0.12874) L


b.

Using a brass bar and hammer, install a new shaft snap ring to the output shaft.