Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › COUNTER GEAR
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297577 COUNTER GEAR A

TL70 MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT THRUST CLEARANCE

a.
C257094E01
1.301,0.165 1.475,0.334 0.174,0.170 10 *a 2.12,0.165 2.336,0.311 0.216,0.147 10 *b

Using a feeler gauge, measure the thrust clearance of the counter shaft 3rd gear and counter shaft 4th gear.

Text in Illustration
*a Counter shaft 4th gear thrust clearance
*b Counter shaft 3rd gear thrust clearance

Standard Clearance
Gear Standard clearance mm (in.) Maximum clearance mm (in.)
Counter shaft 3rd gear 0.10 to 0.35 (0.00393 to 0.0138) 0.35 (0.0138)
Counter shaft 4th gear 0.10 to 0.35 (0.00393 to 0.0138) 0.35 (0.0138)

HINT:

If the clearance exceeds the maximum, adjust it with the 4th inner race thrust washer.



Hide 2.INSPECT RADIAL CLEARANCE

a.
C257095E01
1.457,0.262 1.648,0.426 0.191,0.164 10 *a 2.028,0.262 2.221,0.410 0.193,0.148 10 *b

Using a feeler gauge, measure the radial clearance of the counter shaft 3rd gear and counter shaft 4th gear.

Text in Illustration
*a Counter shaft 4th gear radial clearance
*b Counter shaft 3rd gear radial clearance

Standard Clearance
Gear Standard clearance mm (in.) Maximum clearance mm (in.)
Counter shaft 3rd gear 0.015 to 0.068 (0.000590 to 0.00268) 0.068 (0.00268)
Counter shaft 4th gear 0.065 to 0.115 (0.002559 to 0.00453) 0.115 (0.00453)

HINT:

If the clearance exceeds the maximum, replace the corresponding gear and needle roller bearing or 4th gear bearing inner race all together with a new ones.



Hide 3.REMOVE FRONT COUNTER GEAR BEARING

a.
C257096

Using a snap ring expander, remove the shaft snap ring.


b.
C257097E02
1.771,0.885 2.448,0.76 2.448,0.76 1.75,1.177 true 2.448,0.76 2.115,1.229 true 2.479,0.656 2.781,0.802 0.302,0.146 10 false SST

Using SST and a press, remove the front counter gear bearing.

SST
09950-00020  
09950-60010  (09951-00230)
09950-70010  


Hide 4.REMOVE COUNTER DRIVE GEAR

a.
C257098

Using a snap ring expander, remove the shaft snap ring.


b.
C257099E02
1.708,0.625 2.385,0.688 2.385,0.688 1.708,0.938 true 2.385,0.688 2.052,1.188 true 2.406,0.604 2.719,0.781 0.313,0.177 10 false SST

Using SST and a press, remove the counter drive gear.

SST
09950-00020  
09950-60010  (09951-00230)
09950-70010  (09951-07100)


Hide 5.REMOVE COUNTER SHAFT 4TH GEAR

a.
C257100

Using a snap ring expander, remove the shaft snap ring, and then remove the 4th washer retaining ring and 4th inner race thrust washer.


b.
C257101

Using a screwdriver, pry the 4th gear bearing inner race and turn it counterclockwise along the gear, and remove the 4th gear bearing inner race.


c.
C257102

Remove the counter shaft 4th gear and No. 1 synchronizer ring.


Hide 6.REMOVE COUNTER SHAFT 3RD GEAR

a.
C257103E02
1.292,1.146 0.833,0.813 true 0.521,0.719 0.813,0.875 0.292,0.156 10 false SST

Using SST and a press, remove the No. 2 transmission clutch hub, counter shaft 3rd gear, No. 3 synchronizer ring set and needle roller bearing.

SST
09950-00020  


Hide 7.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.
C257070

Remove the No. 2 transmission hub sleeve, and then remove the 3 No. 1 synchromesh shifting keys, 3 No. 1 synchromesh shifting key springs and 3 balls from the transmission clutch hub.

NOTICE:
·

Use a cloth to prevent the No. 1 synchromesh shifting keys, No. 1 synchromesh shifting key springs and balls from popping out.

·

Do not deform the No. 1 synchromesh shifting key spring.



HINT:

During this operation, keep the No. 2 transmission clutch hub and No. 1 synchromesh shifting key intact.