Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › COUNTER GEAR
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297577 COUNTER GEAR A

TL70 MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL COUNTER SHAFT 3RD GEAR

a.
C257114

Apply manual transmission gear oil to the mounting point of the counter shaft, needle roller bearing and inside surface and taper cone of the counter shaft 3rd gear.


b.

Install the needle roller bearing and counter shaft 3rd gear.


Hide 2.INSTALL NO. 2 TRANSMISSION HUB SLEEVE

a.
C321946E02
2.823,1.875 2.823,2.094 true 2.51,2.323 2.51,2.573 true 2.927,2.448 3.104,2.604 false 2.156,0.292 2.302,0.292 false 1.219,0.344 1.417,0.344 false 1.021,0.229 1.229,0.396 0.208,0.167 10 false *1 1.948,0.188 2.156,0.354 0.208,0.167 10 false *2 2.74,1.688 2.948,1.854 0.208,0.167 10 false *3 2.427,2.573 2.635,2.74 0.208,0.167 10 false *4 3.021,2.604 3.229,2.771 0.208,0.167 10 false *5

Apply manual transmission gear oil to the moving parts of the No. 2 transmission clutch hub.

Text in Illustration
*1 No. 2 Transmission Clutch Hub
*2 No. 2 Transmission Hub Sleeve
*3 Ball
*4 No. 1 Synchromesh Shifting Key
*5 No. 1 Synchromesh Shifting Key Spring
V100135

Front Side


b.

As shown in the illustration, install the No. 2 transmission hub sleeve to the No. 2 transmission clutch hub. Install the 3 No. 1 synchromesh shifting keys and 3 No. 1 synchromesh shifting key springs all together, and then install the balls.

HINT:
·

Install the shifting key ball while holding down the synchromesh shifting key spring. Install the ball while holding down the No. 1 synchromesh shifting key spring.


·

After the installation, let the No. 1 synchromesh shifting key spring settle down.




Hide 3.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

a.
C257115E01
1.889,0.861 2.168,0.861 false 2.194,0.772 2.494,0.928 0.299,0.156 10 SST

Install the No. 3 synchronizer ring set to the counter shaft 3rd gear.

HINT:
·

Align the middle ring claw with the groove in the counter shaft 3rd gear.

·

Align the inner ring claw with the groove in the outer ring.




b.

Using SST and a press, install the No. 2 transmission clutch hub.

SST
09316-60011  (09316-00011)

NOTICE:

Make sure that the No. 3 synchronizer ring set is positioned properly.


HINT:
·

Align the No. 2 transmission clutch hub and the No. 3 synchronizer ring set so that they can fit together.

·

Make sure to press fit the No. 2 transmission clutch hub until it touches the counter shaft.


·

After the press fit, make sure that the No. 3 synchronizer ring set moves toward the thrust direction.




Hide 4.INSTALL COUNTER SHAFT 4TH GEAR

a.
C257116

Install the No. 1 synchronizer ring to the No. 2 transmission clutch hub.

HINT:

Align the No. 2 transmission clutch hub and the No. 1 synchronizer ring so that they can fit together.



b.

Apply manual transmission gear oil to the 4th gear bearing inner race and inside surface and taper cone of the counter shaft 4th gear.


c.

Install the counter shaft 4th gear and 4th gear bearing inner race.

HINT:

To install it, rotate the 4th gear bearing inner race along the gear in a clockwise direction.



Hide 5.INSTALL 4TH INNER RACE THRUST WASHER

a.
C266538E02
0.885,0.792 0.885,0.938 true 0.458,0.76 0.458,0.906 true 0.813,0.615 0.979,0.781 0.167,0.167 10 false *1 0.365,0.573 0.531,0.74 0.167,0.167 10 false *1

Select a 4th inner race thrust washer that is suitable to retain the specific thrust clearance between the 4th gear bearing inner race and 4th inner race thrust washer.

Text in Illustration
*1 4th Inner Race Thrust Washer
V100135

Front Side

Standard clearance:

0 to 0.1 mm (0 to 0.00394 in.)


HINT:

Select the thickest 4th inner race thrust washer possible for installation.


4th Inner Race Thrust Washer Thickness
Part No. Thickness mm (in.) Mark
SU003-03500 3.75 (0.14763) A
SU003-03501 3.80 (0.14960) B
SU003-03502 3.85 (0.15157) C
SU003-03503 3.90 (0.15354) D
SU003-03504 3.95 (0.15551) E
SU003-03505 4.00 (0.15748) F
SU003-03506 4.05 (0.15944) G
SU003-03507 4.10 (0.16141) H


b.

Using a snap ring expander, as shown in the illustration, install a new 4th inner race thrust washer, new 4th washer retaining ring and new shaft snap ring to the counter shaft.


Hide 6.INSTALL COUNTER DRIVE GEAR

a.
C257118E01
1.804,0.434 2.114,0.434 false 2.148,0.351 2.450,0.511 0.302,0.161 10 SST

Using SST and a press, install the counter drive gear.

SST
09309-36010  


Hide 7.INSTALL SHAFT SNAP RING (for Counter Drive Gear)

a.
C257119

Select a shaft snap ring that is suitable to retain the specific thrust clearance between the counter drive gear and shaft snap ring.

Standard clearance:

0 to 0.1 mm (0 to 0.00394 in.)


HINT:

Select the thickest shaft snap ring possible for installation.


Shaft Snap Ring Thickness
Part No. Thickness: mm (in.) Mark
SU003-03581 1.80 (0.07086) A
SU003-03582 1.85 (0.07283) B
SU003-03583 1.90 (0.07480) C
SU003-03584 1.95 (0.07677) D
SU003-03585 2.00 (0.07874) E
SU003-03586 2.05 (0.08070) F


b.

Using a snap ring expander, install a new shaft snap ring to the counter shaft.


Hide 8.INSTALL FRONT COUNTER GEAR BEARING

a.
C266539E03
0.865,1.5 0.865,1.688 true 0.781,1.698 0.979,1.875 0.198,0.177 10 false *1

Using SST and a press, as shown in the illustration, install a new front counter gear bearing while holding it with your hand.

Text in Illustration
*1 Front Counter Gear Bearing
V100135

Front Side

SST
09330-50010  

NOTICE:

Attach SST to the inner race of the front counter gear bearing, and then install the front counter gear bearing.



Hide 9.INSTALL SHAFT SNAP RING (for Front Counter Gear Bearing)

a.
C257293

Select a shaft snap ring that is suitable to retain the specific thrust clearance between the counter gear front bearing and shaft snap ring.

Standard clearance:

0 to 0.1 mm (0 to 0.00394 in.)


HINT:

Select the thickest shaft snap ring possible for installation.


Shaft Snap Ring Thickness
Part No. Thickness: mm (in.) Mark
SU003-03560 2.05 (0.08070) 1
SU003-03558 2.10 (0.08267) 2
SU003-03561 2.15 (0.08464) 3
SU003-03559 2.20 (0.08661) 4
SU003-03562 2.25 (0.08858) 5
SU003-03563 2.30 (0.09055) 6


b.

Using a snap ring expander, install a new shaft snap ring to the counter shaft.