Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY
RM2090E _52 Drivetrain _060677 DRIVE SHAFT / PROPELLER SHAFT _0297580 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR DRIVE SHAFT JOINT BOOT (for LH Side)

a.

Wrap the shaft splines with vinyl tape.

NOTICE:

Wrap the shaft splines with vinyl tape to protect the boot from scratches.



b.

Install the rear drive shaft joint boot in the specified position, and fill of NKG106 grease.

Standard grease capacity:

50 to 60g (1.76 to 2.12 oz.)



Hide 2.INSTALL REAR DRIVE SHAFT JOINT BOOT (for RH Side)

a.

Place the rear drive shaft joint boot at the center of the shaft.


b.
C263278E02
1.292,0.719 1.573,0.354 false 1.01,0.76 0.76,1.729 false 1.573,0.229 1.729,0.385 0.156,0.156 10 false *1 0.667,1.719 0.823,1.875 0.156,0.156 10 false *a

Insert the EDJ cage onto the shaft.

Text in Illustration
*1 EDJ Cage
*a Cutout Portion

HINT:

Insert the EDJ cage with the cutout portion facing the shaft end, since the EDJ cage has an orientation.



Hide 3.INSTALL EDJ INNER RACE

C263273

a.

Install the EDJ inner race on the shaft and fix the rear drive shaft inboard joint LH shaft snap ring in place using pliers.

HINT:

Confirm that the rear drive shaft inboard joint LH shaft snap ring is completely fitted into the shaft groove.



Hide 4.INSTALL EDJ CAGE

a.
C263285E01
2.385,0.698 2.594,0.49 2.594,0.49 2.823,0.49 false 1.198,0.333 1.469,0.333 1.469,0.333 1.708,0.552 true 2.844,0.406 3.042,0.583 0.198,0.177 10 false *1 0.99,0.24 1.188,0.417 0.198,0.177 10 false *2

Install the EDJ cage to EDJ inner race fixed upon the shaft.

Text in Illustration
*1 EDJ Cage
*2 EDJ Inner Race

HINT:

Fit the cage with the protruding section aligned with the track on the EDJ inner race, and turn by a half pitch.



b.

Fill of NKG814 grease into the inner side of the rear drive shaft inboard joint assembly LH.

Standard grease capacity:

80 to 90 g (2.82 to 3.17 oz)



c.

Apply a thin coat of NKG814 grease to the cage pocket and 8 ball bearings.


d.

Insert the 8 ball bearings into the cage pocket.


e.
C263271E03
1.563,0.927 1.563,0.448 1.563,0.448 2.333,0.448 true 2.042,1.031 2.042,0.677 2.042,0.677 2.594,0.677 false 1.792,1.719 1.792,2.042 1.792,2.042 2.344,2.042 true 2.385,0.333 2.542,0.479 0.156,0.146 10 false *1 2.635,0.583 2.792,0.729 0.156,0.146 10 false *2 2.396,1.948 2.552,2.094 0.156,0.146 10 false *3

Align the rear drive shaft inboard joint track and ball positions, and place the shaft, EDJ inner race, cage and ball bearings in the original positions, and then fix the rear drive shaft inboard joint assembly LH in place.

Text in Illustration
*1 Rear Drive Shaft Inboard Joint Assembly LH
*2 NKG814 Grease
*3 Balls (8 Pieces)


f.
C263275

Install the hole snap ring in the groove on the rear drive shaft inboard joint assembly LH.

HINT:
·

Assure that the balls, cage and EDJ inner race are completely fitted in the rear drive shaft inboard joint assembly LH.

·

Use care not to place the matched position of rear drive shaft inboard joint LH shaft snap ring in the ball groove of rear drive shaft inboard joint.

·

Pull the shaft lightly and assure that the circlip is completely fitted in the groove.




g.

Apply an even coat of NKG814 grease to the entire inner surface of the boot. Also apply grease to the shaft.

Standard grease capacity:

20 to 30 g (0.71 to 1.06 oz)



h.

Install the rear drive shaft joint boot taking care not to twist it.

HINT:
·

The inside of the large end of rear drive shaft joint boot and the boot groove shall be cleaned so as to be free from grease and other substances.

·

When installing the rear drive shaft joint boot, position the rear drive shaft inboard joint at center of the stroke.




Hide 5.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.

Apply NKG106 grease to the interior surface of the new rear drive shaft outboard joint boot clamp.


b.
C264279

Mount the rear drive shaft outboard joint boot clamp to the rear drive shaft joint boot, and temporarily bend the lever.

CAUTION:

Make sure that protective gloves are worn during work in order to prevent injury to hands, etc.


NOTICE:
·

When temporarily bending the lever, make sure that the band and lever are not twisted.

·

In order to prevent breakage of the rear drive shaft outboard joint boot clamp, do not repeatedly bend the lever.




c.
C264280E02
1.531,0.292 1.74,0.469 0.208,0.177 10 false *a 2.208,2.052 2.417,2.229 0.208,0.177 10 false *b

While pushing the joint towards the work surface, press down using one hand, and fold the lever while turning the drive shaft forward.

Text in Illustration
*a Weight
*b Ground

NOTICE:
·

Do not damage the deflector.

·

Do not raise the joint off the work surface.




d.
C264281

Using a plastic hammer, tap the buckle to affix.

NOTICE:
·

Do not hit the buckle with the plastic hammer excessively hard

·

Install the clamp so that the lever does not rise.

·

Make sure that the gap between the two buckles is parallel.




Hide 42346A 6.INSTALL REAR NO.2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.
C264282

Install a new rear No.2 drive shaft outboard joint boot clamp to the rear drive shaft joint boot and temporarily bend the lever.

CAUTION:

Make sure that protective gloves are worn during work in order to prevent injury to hands, etc.


NOTICE:
·

When temporarily bending the lever, make sure that the band and lever are not twisted.

·

In order to prevent breakage of the rear No.2 drive shaft outboard joint boot clamp, do not repeatedly bend the lever.




b.
C264284E02
2.26,1.615 2.49,1.219 2.49,1.219 2.698,1.219 true 2.698,1.125 2.885,1.281 0.188,0.156 10 false *a

Use water pump pliers to tighten the rear No.2 drive shaft outboard joint boot clamp, and temporarily fasten.

Text in Illustration
*a The End is Near the Center of the Lever.


c.
C264283

Use a plastic hammer to tap the buckle to affix.

NOTICE:
·

Do not hit the buckle with the plastic hammer excessively hard.

·

Affix the lever so that it does not rise.

·

Make sure that the gap between the two buckles is parallel.




Hide 42347B 7.INSTALL REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP

HINT:

Work on the rear No. 2 drive shaft inboard joint boot clamp in the same way as the rear No. 2 drive shaft outboard joint boot clamp.


Hide 42347A 8.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP

HINT:
·

Work on the rear drive shaft inboard joint boot clamp in the same way as the rear drive shaft outboard joint boot clamp.

·

Use NKG814 grease for application to the inside of the rear drive shaft inboard joint boot clamp.