Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › 2012.03–2017.03
RM2090E _52 Drivetrain _060678 AXLE AND DIFFERENTIAL _0297584 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 47710A 2.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Hang the caliper using a piece of string or equivalent.



Hide 43502D 4.REMOVE FRONT AXLE HUB BOLT

a.

Using SST, remove the front axle hub bolt from the front axle hub sub-assembly.

C265372E03
0.958,0.438 1.167,0.438 false 1.198,3.198 1.406,3.198 1.406,3.198 1.896,2.938 false 5.99,1.875 5.771,1.875 5.771,1.875 5.771,2.469 false 6.313,2.104 6.104,2.104 6.104,2.104 6.104,2.427 false 6.771,3.188 6.771,2.833 6.771,2.833 6.542,2.833 false 6.771,2.917 6.542,2.917 false 5.396,3.292 5.604,3.292 5.604,3.292 5.604,3.063 false 1.177,0.333 1.365,0.521 0.188,0.188 10 false *a 0.896,3.125 1.26,3.313 0.365,0.188 10 false SST 6.021,1.781 6.208,1.969 0.188,0.188 10 false *3 6.333,2 6.521,2.188 0.188,0.188 10 false *1 6.698,3.188 6.885,3.375 0.188,0.188 10 false *4 5.219,3.208 5.406,3.396 0.188,0.188 10 false *2

Text in Illustration
*1 Nut *2 Body
*3 Claw *4 SST (Spacer B)
*a Place a Wrench Here - -
V100135

Molybdenum Grease
V100136

Turn

SST
09960-20010  (09961-02010, 09961-02060)

CAUTION:

Before working, apply molybdenum grease to the bolt threads and bolt tip of SST.


NOTICE:
·

Install SST so that claw and body are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not damage the front disc brake dust cover.

·

Do not damage the front axle hub.

·

Do not damage the steering knuckle.




Hide 43502D 5.INSTALL FRONT AXLE HUB BOLT

a.
C257542E03
2.729,0.427 3.167,0.25 true 3.01,0.885 3.01,1.229 true 1.5,0.813 1.594,0.24 true 2.74,1.573 2.896,1.719 0.156,0.146 10 false *a 2.917,1.24 3.073,1.385 0.156,0.146 10 false *1 0.604,1.698 0.76,1.844 0.156,0.146 10 false *b 1.5,0.052 1.656,0.198 0.156,0.146 10 false *1 3.208,0.104 3.365,0.25 0.156,0.146 10 false *2

Set a new axle hub bolt onto the front axle hub, and tighten the nut (M12 x P1.25mm (0.0492 in.)) through the washer plate to install the axle hub bolt.

Text in Illustration
*1 Nut
*2 Washer
*a Turn
*b Hold

NOTICE:

Install the nuts to prevent damage to the front axle hub bolts.



Hide 47710A 7.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 new bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 8.INSTALL FRONT WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)