Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE
RM2090E _52 Drivetrain _060678 AXLE AND DIFFERENTIAL _0297586 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502C 1.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

Hide 47782 2.REMOVE FRONT DISC BRAKE DUST COVER LH

a.
C257512

Remove the 3 bolts and the front disc brake dust cover LH.


Hide 45047 3.DISCONNECT TIE ROD SUB-ASSEMBLY LH

a.
C257549

Remove the cotter pin and nut.


b.

Install the SST (spacer B) to the tie rod assembly.

NOTICE:

As SST may get damaged, make sure the space between the tie rod and the spacers is not less than 1 mm (0.0394 in.).



c.

Using SST, disconnect the tie rod assembly.

C259936E03
2.167,0.635 2.635,1.021 false 5.823,2.198 5.656,2.198 5.656,2.198 5.656,1.677 false 6.031,1.698 6.031,2.01 6.031,2.01 6.229,2.01 false 6.427,1.052 6.427,0.677 6.427,0.677 6.656,0.677 false 5.594,0.938 5.594,0.656 5.594,0.656 5.313,0.656 false 1.115,1.667 0.885,1.667 false 1.865,0.552 2.177,0.719 0.313,0.167 10 false SST 6.24,1.948 6.396,2.094 0.156,0.146 10 false *1 5.146,0.583 5.313,0.74 0.167,0.156 10 false *2 5.833,2.104 6,2.26 0.167,0.156 10 false *3 6.667,0.573 6.833,0.75 0.167,0.177 10 false *4 6.938,1.104 7.104,1.281 0.167,0.177 10 false *a 1.125,1.594 1.292,1.771 0.167,0.177 10 false *b

Text in Illustration
*1 Nut *2 Body
*3 Claw *4 SST (Spacer B)
*a 1 mm (0.0394 in.) *b Place a Wrench Here
V100135

Molybdenum Grease
V100136

Turn

SST
09960-20010  (09961-02010, 09961-02060)

CAUTION:

Apply the molybdenum grease to the end and threads of the SST bolt.


NOTICE:
·

Install SST so that the claw and body are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not damage the dust cover on the tie rod end sub-assembly.

·

Do not damage the tie-rod end.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle.




Hide 48640 4.REMOVE FRONT LOWER SUSPENSION ARM ASSEMBLY LH

a.
C256600

Remove the cotter pin and nut.


b.

Install the SST (spacer B) to the front lower suspension arm assembly LH.

NOTICE:

As SST may get damaged, make sure the space between the front lower suspension arm assembly LH and the spacers is not less than 1 mm (0.0394 in.).



c.

Using SST, disconnect the front lower suspension arm assembly LH.

C256684E03
3.323,2.292 3.792,2.292 3.792,2.292 3.792,2.031 false 0.573,1.042 0.792,1.042 0.792,1.042 0.792,1.365 false 1.385,2.521 1.552,2.521 1.552,2.521 1.552,1.99 false 1.208,2.031 1.208,2.302 1.208,2.302 1.01,2.302 false 1.531,1.229 1.531,0.948 1.531,0.948 1.823,0.948 false 6.063,1.927 6.281,1.927 false 3.021,2.229 3.323,2.375 0.302,0.146 10 false SST 0.865,2.219 1.021,2.375 0.156,0.156 10 false *1 0.417,0.958 0.563,1.125 0.146,0.167 10 false *4 1.219,2.438 1.375,2.594 0.156,0.156 10 false *3 1.844,0.875 2,1.042 0.156,0.167 10 false *2 0.156,1.417 0.313,1.583 0.156,0.167 10 false *a 5.896,1.844 6.052,2 0.156,0.156 10 false *b

Text in Illustration
*1 Nut *2 Body
*3 Claw *4 SST (Spacer B)
*a 1 mm (0.0394 in.) *b Place a Wrench Here
V100135

Molybdenum Grease
V100136

Turn

SST
09960-20010  (09961-02010, 09961-02060)

CAUTION:

Apply the molybdenum grease to the end and threads of SST bolt.


NOTICE:
·

Install SST so that the claw and body are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not damage the dust cover on the front suspension lower arm assembly.

·

Do not damage the front lower arm sub-assembly.

·

Do not damage the front disc brake dust cover.

·

Do not damage the steering knuckle.




Hide 43212 5.REMOVE STEERING KNUCKLE LH

a.
C256596

Remove the steering knuckle LH with the 2 bolts and 2 nuts.

NOTICE:

When removing the nuts, keep the bolts from rotating.