Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM2090E _53 Suspension _060680 FRONT SUSPENSION _0297600 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for the LH side.

·

Use the same procedure for the RH side and LH side.



PROCEDURE

Hide 48331C 1.INSTALL FRONT SPRING BUMPER LH

a.

Install the front spring bumper LH to the front shock absorber assembly LH.


Hide 48157C 2.INSTALL FRONT COIL SPRING INSULATOR UPPER LH

a.

Install the front coil spring insulator upper LH to the front shock absorber assembly LH.


Hide 48132 3.INSTALL FRONT COIL SPRING LH

a.

Secure the SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C256686E01
2.868,0.951 3.156,1.087 0.288,0.136 10 SST 2.848,1.024 2.475,1.024 false

Install SST to the front coil spring LH with the hooks spread as far apart as possible from each other.


c.
C263591

Attach the arm of SST to the diameter of the coil spring.

CAUTION:
·

Make sure that the front coil spring LH is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws on the hooks are securely engaged.




d.

Using SST, compress the front coil spring LH.

CAUTION:
·

If the front coil spring LH bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




e.
C262322E02
1.969,1.271 1.969,0.875 1.969,0.875 2.229,0.875 false 2.458,1.417 2.729,1.646 2.729,1.646 2.813,1.646 true 2.25,0.802 2.406,0.948 0.156,0.146 10 false *1 2.677,1.083 2.833,1.229 0.156,0.146 10 false *a 2.865,1.563 3.021,1.708 0.156,0.146 10 false *b

Install the front coil spring LH so that the lower end of the spring and lower side spring seat stopper are aligned.

Text in Illustration
*1 Front Coil Spring LH
*a 0 to 10 mm (0 to 0.397 in.)
*b Spring Seat Stopper


Hide 48331C 4.INSTALL FRONT SPRING BUMPER LH

a.

Install the front spring bumper LH to the front shock absorber assembly LH.


Hide 48152 5.INSTALL FRONT SPRING SEAT

a.

Install the front spring seat to the front shock absorber assembly LH.


Hide 48609 6.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the front suspension support sub-assembly LH to the front shock absorber assembly LH.


Hide 48609E 7.INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT LH

a.

Using a long socket hexagon wrench 6, fix the shock absorber rod.


b.
C266612E03
0.49,2.771 0.677,2.771 0.677,2.771 0.906,2.938 false 0.188,2.698 0.49,2.875 0.302,0.177 10 false SST 0.99,4 1.188,4.177 0.198,0.177 10 false *a 1.635,1.271 1.833,1.448 0.198,0.177 10 false *b

Using SST, install a new front support to front shock absorber nut LH to the front shock absorber assembly LH.

SST
09729-97202  

Text in Illustration
*a Fulcrum Length
*b 40 mm (1.575 in.)

Torque:
without SST : 55 N*m (561 kgf*cm, 41 ft.*lbf)
with SST : 49 N*m (495 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Use a torque wrench wiht a fulcrum length of 300 mm (11.81 in.)

·

Be careful not to damage or deform the threaded section.

·

Securely set the long socket hexagon wrench 6.