Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM2090E _53 Suspension _060681 REAR SUSPENSION _0297605 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for the LH side.

·

Use the same procedure for the RH and LH sides.



PROCEDURE

Hide 48341B 1.INSTALL REAR NO. 1 SPRING BUMPER LH

a.

Install the rear No. 1 spring bumper LH to the rear shock absorber assembly LH.


Hide 48559D 2.INSTALL REAR NO. 1 SHOCK ABSORBER DUST COVER LH

a.

Install the rear No. 1 shock absorber dust cover LH to the rear shock absorber assembly LH.


Hide 48231B 3.INSTALL REAR COIL SPRING LH

a.
C256686E01
2.868,0.951 3.156,1.087 0.288,0.136 10 SST 2.848,1.024 2.475,1.024 false

Secure the SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C263591

Set the arm hooks of SST on the middle line on the spring outer circumference.

CAUTION:
·

Install SST to the rear coil spring LH so that the distance between the upper and lower hooks is as wide as possible within the installation area.

·

Check that the claws of the hooks are attached securely.




c.

Using SST, compress the rear coil spring LH.

CAUTION:
·

During the work, if the rear coil spring LH is arched, immediately stop the work and reset SST.

·

Do not compress the spring until each coil contacts each other.

·

Do not use an impact wrench.




d.
C261009E03
2.698,0.677 3.052,0.677 3.052,0.677 3.052,1.083 false 2.573,1.229 2.406,1.573 2.406,1.573 2.229,1.573 true 2.49,0.594 2.635,0.729 0.146,0.135 10 false *1 2.177,0.885 2.333,1.104 0.156,0.219 10 false *a 2.021,1.49 2.188,1.688 0.167,0.198 10 false *b

Install the rear coil spring LH with the lower end of the coil spring and the stopper of the spring seat fit.

HINT:

Fit the lower end of the rear coil spring LH into the gap of the absorber lower seat.


Text in Illustration
*1 Rear Coil Spring LH
*a 0 to 10 mm (0 to 0.394 in.)
*b Stopper of spring seat


Hide 48482 4.INSTALL REAR UPPER SPRING SEAT LH

a.

Install the rear upper spring seat LH to the rear coil spring LH.


Hide 48760B 5.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY LH

a.

Install the rear suspension support assembly LH to the rear shock absorber assembly LH.


Hide 48760C 6.INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER NUT LH

a.
C260997E02
1.667,4.271 0.771,3.948 true 0.073,0.063 0.323,0.344 0.25,0.281 10 false *a 1.854,0.063 2.094,0.344 0.24,0.281 10 false *b 0.292,0.396 0.635,0.656 0.344,0.26 10 false *c 0.573,3.833 0.771,4.063 0.198,0.229 10 false *d 2.948,0.396 3.198,0.708 0.25,0.313 10 false *c

Temporarily tighten a new rear support to rear shock absorber nut LH to the rear shock absorber assembly LH.

Text in Illustration
*a for LH side
*b for RH side
*c 75 to 85°
*d Lower End
V100135

Outside of the Vehicle
V100136

Front of the Vehicle


b.

Adjust the rear suspension support assembly LH to the installation position of the shock absorber so that the studs are positioned as shown in the illustration.

NOTICE:

Make sure that the left coil spring end faces toward the rear of the vehicle and the right spring end faces toward the front.



c.

Release SST and remove it from the rear coil spring LH.

CAUTION:

Do not use an impact wrench


NOTICE:

Remove SST after confirming the position of the suspension support assembly.



d.
C266614E02
1.771,2.5 1.99,1.781 1.99,1.781 2.219,1.781 true 1.563,2.573 1.01,2.094 1.01,2.094 0.792,2.094 true 1.104,3.792 1.292,3.979 0.188,0.188 10 false *a 1.531,1.229 1.719,1.417 0.188,0.188 10 false *b 2.271,1.708 2.573,1.865 0.302,0.156 10 false SST 0.583,2.031 0.771,2.219 0.188,0.188 10 false *1

Install SST to the rear support to rear shock absorber nut LH. And then, using a long socket hexagon 5 mm, hold the piston rod of the rear shock absorber assembly LH, and tighten the rear support to rear shock absorber nut LH using a union nut wrench 14 mm.

Text in Illustration
*1 Union nut wrench 14 mm
*a Fulcrum length
*b 25 mm (0.984 in.)

SST
09729-18010  

Torque:
without SST : 25 N*m (255 kgf*cm, 18 ft.*lbf)
with SST : 23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:
·

Use a torque wrench with a fulcrum length of 300 mm (11.81 in.)

·

Be careful not to damage or deform the threads.

·

Securely set the long socket hexagon 5 mm.