Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2014.05
RM2090E _53 Suspension _060682 TIRE PRESSURE MONITORING _0297611 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C305304E03
5.167,3 6.875,3.469 1.708,0.469 10 false Tire Pressure Warning ECU and Receiver 5.385,0.667 5.833,0.896 0.448,0.229 10 false +B 5.135,0.573 5.292,0.76 0.156,0.188 10 false 7 5.146,1.344 5.302,1.531 0.156,0.188 10 false 1 5.417,1.438 5.688,1.667 0.271,0.229 10 false IG 5.177,2.833 5.531,3.01 0.354,0.177 10 false H28 0.969,0.646 1.917,0.99 0.948,0.344 10 false from Battery 2.896,0.833 3.375,1.073 0.479,0.24 10 false MPX-B 2.854,1.625 3.479,1.844 0.625,0.219 10 false ECU IG1 0.458,1.438 1.906,1.781 1.448,0.344 10 false from IG1 NO. 1 Relay 5.115,2.031 5.323,2.229 0.208,0.198 10 false 12 5.406,2.188 6.031,2.458 0.625,0.271 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - BATTERY AND BODY GROUND)
a.

Disconnect the H28 tire pressure warning ECU and receiver connector.


b.
U147015E05
1.146,1.74 0.802,1.74 false 0.073,0.073 0.417,0.417 0.344,0.344 10 false *a 0.646,1.667 0.906,1.896 0.26,0.229 10 false IG 0.427,1.302 0.813,1.563 0.385,0.26 10 false H28

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H28-1 (IG) - Body ground Ignition switch ON 11 to 14 V
H28-1 (IG) - Body ground Ignition switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H28-12 (GND) - Body ground Always Below 1 Ω




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR