Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2014.05
RM2090E _53 Suspension _060682 TIRE PRESSURE MONITORING _0297611 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2177/77  Initialization not Completed  


DESCRIPTION

Initialization is necessary if one of the following occurs:

·

Tire pressure warning ECU and receiver is replaced.

·

Tire pressure warning valve and transmitter is replaced.

·

Tires with a different tire standard pressure are installed.

·

Tires are rotated.

·

A new vehicle is delivered.


DTC No. DTC Detection Condition Trouble Area
C2177/77

All conditions below are met:


·

During initialization

·

Tire pressure warning valve and transmitter is not in stop mode

·

Signal is not received from tire pressure warning valve and transmitter for 20 minutes or more

·

Vehicle speed is more than 8 km/h (5 mph) for a total of 20 minutes


·

Tire pressure warning valve and transmitter

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.



PROCEDURE

1.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the vehicle is not located in an area such as described below:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may come on after blinking 1 minute only in a particular area due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio transmissions may be interrupted due to the surroundings, or devices installed by the user.





OK

2.PERFORM INITIALIZATION

NG

CHECK IF ANY DEVICE IS INSTALLED BY USER

2.PERFORM INITIALIZATION

NEXT

3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID1 Tire Inflation Pressure ID1 tire inflation pressure /
min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi)
max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.*
ID2 Tire Inflation Pressure ID2 tire inflation pressure /
min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi)
max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.*
ID3 Tire Inflation Pressure ID3 tire inflation pressure /
min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi)
max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.*
ID4 Tire Inflation Pressure ID4 tire inflation pressure /
min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi)
max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.*

HINT:
·

*: It may take a few minutes until the values are displayed.

·

When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.



Result:
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B




A

B

END