Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.06
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C238830E01
0.209,0.168 0.407,0.338 0.198,0.170 10 *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -

Terminal No. (Symbol) Terminal Description
1 (+BM) ABS motor relay power supply
2 (SPD) Speed signal output
3 - (Not used)
4 (FR-) Front wheel speed RH (-) signal input
5 - (Not used)
6 - (Not used)
7 - (Not used)
8 (FL-) Front wheel speed LH (-) signal input
9 (CSW2) TRACK switch input
10 - (Not used)
11 - (Not used)
12 (CSW1) VSC OFF switch input
13 (GND2) Pump motor ground
14 (CANL) CAN communication line L
15 - (Not used)
16 (FR+) Front wheel speed RH (+) signal input
17 (RR+) Rear wheel speed RH (+) signal input
18 (RL-) Rear wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) signal input
20 - (Not used)
21 - (Not used)
22 - (Not used)
23 - (Not used)
24 - (Not used)
25 (+BS) ABS solenoid relay power supply
26 (CANH) CAN communication line H
27 - (Not used)
28 (IG1) IG1 power source input
29 (RR-) Rear wheel speed RH (-) signal input
30 (STP) Stop light switch input
31 (RL+) Rear wheel speed LH (+) signal input
32 - (Not used)
33 - (Not used)
34 - (Not used)
35 - (Not used)
36 - (Not used)
37 - (Not used)
38 (GND1) Skid control ECU ground


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage and resistance on the wire harness side.

U147014E03
0.219,0.135 0.448,0.344 0.229,0.208 10 false *a 1.635,0.802 1.906,1.042 0.271,0.24 10 false A5

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -

HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) because the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A5-1 (+BM) - Body ground W - Body ground ABS motor relay power supply Always 11 to 14 V
A5-9 (CSW2) - Body ground P - Body ground TRACK switch input TRACK switch held ON → OFF (Not pressed) Below 1 Ω → 10 kΩ or higher
A5-12 (CSW1) - Body ground O - Body ground VSC OFF switch input VSC OFF switch held ON → OFF (Not pressed) Below 1 Ω → 10 kΩ or higher
A5-13 (GND2) - Body ground B - Body ground Pump motor ground Always Below 1 Ω
A5-25 (+BS) - Body ground G - Body ground ABS solenoid relay power supply Always 11 to 14 V
A5-28 (IG1) - Body ground G-R - Body ground IG1 power source input Ignition switch ON 11 to 14 V
A5-30 (STP) - Body ground R - Body ground Stop light switch input Stop light switch ON → OFF (Brake pedal depressed → released) 11 to 14 V* → Below 1.5 V
A5-38 (GND1) - Body ground B - Body ground Skid control ECU ground Always Below 1 Ω

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.