Home › Brake › BRAKE (REAR) › REAR BRAKE (for Floating Type Caliper)
RM2090E _54 Brake _060687 BRAKE (REAR) _0297635 REAR BRAKE(for Floating Type Caliper) A

BRAKE (REAR)  REAR BRAKE(for Floating Type Caliper)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RH and LH sides.

·

The procedure listed below is for LH side.



PROCEDURE

Hide 47769A 1.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH

a.
C261030

Apply a light layer of lithium soap base glycol grease to the inner face of a new rear disc brake cylinder slide bush.

Text in Illustration
V100144

Lithium Soap Base Glycol Grease

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake cylinder slide bush.



b.

Install the 2 rear disc brake cylinder slide bushes to the caliper support bracket.


Hide 47815 2.INSTALL REAR DISC BRAKE REAR CYLINDER SLIDE PIN

a.
C261031E02
1.063,1.354 1.385,1.073 false 2.104,1.802 2.302,1.615 false 0.875,1.323 1.052,1.49 0.177,0.167 10 false *1 1.927,1.76 2.104,1.927 0.177,0.167 10 false *2

Apply a light layer of lithium soap base glycol grease to the contact face between a new bush and rear disc brake rear cylinder rear disc brake cylinder slide pin.

Text in Illustration
*1 rear disc brake rear cylinder rear disc brake cylinder slide pin
*2 Bush
V100144

Lithium Soap Base Glycol Grease


b.

Install the new bush to the rear disc brake rear cylinder rear disc brake cylinder slide pin.


c.

Apply a light layer of lithium soap base glycol grease to entire circumference of the rear disc brake rear cylinder rear disc brake cylinder slide pin and fitting part.


d.

Install the rear disc brake rear cylinder rear disc brake cylinder slide pin to the caliper support bracket.


Hide 47814 3.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C261032

Apply a light layer of lithium soap base glycol grease to entire circumference of the rear disc brake cylinder slide pin and fitting part.

Text in Illustration
V100144

Lithium Soap Base Glycol Grease


b.

Install the rear disc brake cylinder slide pin to the caliper support bracket.


Hide 42431 4.INSTALL REAR DISC

a.

Align the matchmarks placed when removing, install the rear disc to the axle hub.

HINT:

When using a new rear disc, install it so that rear disc runout is minimum.



Hide 5.ADJUST PARKING BRAKE

Hide 6.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the parking brake shoe adjusting hole plug to the rear disc.


Hide 7.INSTALL CALIPER SUPPORT BRACKET

a.

Install the caliper support bracket with new 2 bolts.

Torque:
Bolt Type A : 66 N*m (673 kgf*cm, 49 ft.*lbf)
Bolt Type B : 110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Check that there is no dirt, foreign matter or rust on the caliper support bracket and clean if necessary.


HINT:
C398291E01
0.177,0.146 0.49,0.344 0.313,0.198 10 false *A 0.177,1.25 0.49,1.448 0.313,0.198 10 false *B 0.75,0.458 1.063,0.656 0.313,0.198 10 false *a 0.74,1.573 1.052,1.771 0.313,0.198 10 false *a

Bolt type A and bolt type B can be distinguished by the sizes of the mounting bolts.

Bolt Type Width Across Flats
A 14 mm (0.551 in.)
B 17 mm (0.669 in.)

Text in Illustration
*A Bolt Type A
*B Bolt Type B
*a Width Across Flats



b.
C256672

Apply a light layer of MP grease to contact section of the caliper support bracket with the rear disc brake pad support plate.

Text in Illustration
V100144

MP Grease


Hide 47816 8.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.
C256671

Apply a light layer of MP grease to contact section of the rear disc brake pad support plate with the rear disc brake pad.

Text in Illustration
V100144

MP Grease


b.

Install the rear disc brake pad support plate to the caliper support bracket.


Hide 9.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.
C261033E02
0.375,1.698 0.375,1.979 false 1.271,1.792 1.271,2.01 false 2.052,1.635 2.052,1.979 false 2.615,1.188 2.615,1.625 false 3.083,1.323 3.083,1.635 false 0.427,3.99 0.427,4.281 false 1.26,4.073 1.26,4.302 false 2.229,3.917 2.229,4.177 false 3.083,3.615 3.083,3.875 false 0.125,2.313 0.385,2.51 0.26,0.198 12 false *B: 0.125,0.073 0.385,0.271 0.26,0.198 12 false *A: 3,3.885 3.177,4.052 0.177,0.167 10 false *2 3,1.656 3.177,1.823 0.177,0.167 10 false *2 2.552,1.656 2.729,1.823 0.177,0.167 10 false *2 2.156,4.198 2.333,4.365 0.177,0.167 10 false *1 1.188,4.323 1.365,4.49 0.177,0.167 10 false *1 0.333,4.302 0.51,4.469 0.177,0.167 10 false *2 1.979,1.99 2.156,2.156 0.177,0.167 10 false *1 1.188,2.063 1.365,2.229 0.177,0.167 10 false *1 0.302,2.052 0.479,2.219 0.177,0.167 10 false *2

Apply disc brake grease to the rear disc brake anti squeal shim kit.

Text in Illustration
*A Solid Disc Brake
*B Ventilated Disc Brake
*1 Rear Disc Brake Pad Kit
*2 Rear Disc Brake Anti Squeal Shim Kit
V100135

Disc Brake Grease


b.

Put the rear disc anti squeal shim kit to each rear disc brake pad.


Hide 10.INSTALL REAR DISC BRAKE PAD KIT

a.

Install the rear disc brake pad kit to the caliper support bracket.


Hide 11.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.

Install the rear disc brake cylinder assembly LH to the caliper support bracket with the 2 bolts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

NOTICE:

Check that there is no dirt, foreign matter or rust on the rear disc brake cylinder assembly LH and clean if necessary.



Hide 47319F 12.CONNECT REAR FLEXIBLE HOSE LH

a.

Connect the rear left flexible hose with 2 new gaskets and the new union bolt.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 15.INSPECT BRAKE FLUID LEAK

Hide 17.INSTALL REAR WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)