Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TERMINALS OF ECU  


CHECK POWER STEERING ECU


U147194E02
0.177,0.021 0.594,0.385 0.417,0.365 10 false *a 1.938,0.792 2.167,0.979 0.229,0.188 10 false z1 3.594,0.625 3.823,0.813 0.229,0.188 10 false z2 4.313,0.625 4.583,0.813 0.271,0.188 10 false A15 5.052,0.635 5.323,0.823 0.271,0.188 10 false A14

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

HINT:

As connector z1 uses a lock lever, each terminal cannot be checked while the connector is still connected to the power steering ECU.


Terminal No. (Symbol) Terminal Description
z1-1 (V) V phase motor output
z1-2 (U) U phase motor output
z1-3 (W) W phase motor output

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A14-1 (PIG) - A14-2 (PGND) W - B Motor power supply Always 9 to 16 V
A14-2 (PGND) - Body ground B - Body ground Power ground Always Below 1 Ω
A15-1 (CANH) - A15-7 (CANL) B - W CAN communication line Ignition switch off 57 to 63 Ω
A15-6 (IG) - A14-2 (PGND) G-W - B IG power supply Ignition switch ON 9 to 16 V
z2-5 (RZV) - A14-2 (PGND) R - B Rotation angle sensor excitation output signal Engine running, steering wheel being turned 0.68 to 4.42 V
z2-7 (RZG) - A14-2 (PGND) B - B Rotation angle sensor excitation circuit ground Always Below 1 Ω
z2-13 (RZCS) - A14-2 (PGND) L - B Rotation angle sensor COS aspect input signal Engine running, steering wheel being turned 0.68 to 4.42 V
z2-14 (RZSN) - A14-2 (PGND) Y - B Rotation angle sensor SIN aspect input signal Engine running, steering wheel being turned 0.68 to 4.42 V
z2-8 (TRQ1) - z2-11 (TRQG) W - B Torque sensor signal 1 Engine running, steering wheel not turned (without load) 2.3 to 2.7 V
Engine running, steering wheel turned to right with vehicle stopped 2.3 to 3.8 V
Engine running, steering wheel turned to left with vehicle stopped 1.2 to 2.7 V
z2-9 (TRQV) - z2-11 (TRQG) R - B Torque sensor power supply Ignition switch ON 4.5 to 5.5 V
z2-10 (TRQ2) - z2-11 (TRQG) Y - B Torque sensor signal 2 Engine running, steering wheel not turned (without load) 2.3 to 2.7 V
Engine running, steering wheel turned to right with vehicle stopped 1.2 to 2.7 V
Engine running, steering wheel turned to left with vehicle stopped 2.3 to 3.8 V
z2-11 (TRQG) - Body ground B - Body ground Torque sensor ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.