Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the EPS warning light comes on. At this time, the power steering ECU assembly stores a DTC in its memory.

WIRING DIAGRAM

C200250E14
0.49,4 2.396,4.24 1.906,0.24 10 false Combination Meter Assembly 0.5,3.833 0.854,4.042 0.354,0.208 10 false D7 5.51,3.875 6.885,4.51 1.375,0.635 10 false Power Steering ECU Assembly 5.417,3.208 5.75,3.365 0.333,0.156 10 false A14 5.417,1.875 5.75,2.031 0.333,0.156 10 false A14 5.417,2.563 5.75,2.719 0.333,0.156 10 false A15 4.229,2.021 4.563,2.177 0.333,0.156 10 false EPS 4.104,2.698 5.125,2.854 1.021,0.156 10 false ECU IG1 2.125,1.865 2.917,2.052 0.792,0.188 10 false from Battery 1.958,2.563 3.042,2.75 1.083,0.188 10 false from IG1 Circuit 5.802,1.865 6.135,2.021 0.333,0.156 10 false PIG 5.792,2.552 6.125,2.708 0.333,0.156 10 false IG 5.802,3.219 6.396,3.375 0.594,0.156 10 false PGND 5.49,1.646 5.604,1.813 0.115,0.167 10 false 1 5.5,2.354 5.615,2.521 0.115,0.167 10 false 6 5.5,3 5.615,3.167 0.115,0.167 10 false 2 1.448,4.417 3.375,4.604 1.927,0.188 10 false CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly is replaced with a new one, perform rotation angle sensor initialization and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When the power supply voltage to the power steering ECU assembly (terminals IG and PIG) drops, required steering effort increases and the EPS warning light turns on.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Turn the ignition switch to ON.


b.

Check the indication condition of the EPS warning light by wiggling the power steering ECU assembly connector and wire harness up and down, and right and left.

OK:

EPS warning light indication condition does not change.




OK

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

OK:

DTC is not output.




OK

3.READ VALUE USING GTS (IG POWER SUPPLY)

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.READ VALUE USING GTS (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V The ignition switch is ON.

OK:

The normal condition value is displayed the GTS.




OK

4.READ VALUE USING GTS (PIG POWER SUPPLY)

NG

6.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
4.READ VALUE USING GTS (PIG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to active motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V The engine is running and power steering is operating.

OK:

The normal condition value is displayed the GTS.




OK

5.PERFORM ACTIVE TEST USING GTS (METER / GAUGE SYSTEM)

NG

7.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
5.PERFORM ACTIVE TEST USING GTS (METER / GAUGE SYSTEM)
a.

Perform the Active Test of the combination meter using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. EPS EPS warning light OFF/ON Vehicle is stopped and engine is idling


b.

Check that the EPS warning light operates in accordance with the Active Test.

HINT:

Reconnect the connectors and restore the vehicle to its previous condition before checking the combination meter.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
a.
U146982E04
2.188,1.979 2.417,1.958 true 1.875,4.01 2.188,4.01 true 0.24,0.115 0.438,0.281 0.198,0.167 10 false *a 2.458,1.854 2.771,2.021 0.313,0.167 10 false IG 2.229,3.927 2.813,4.094 0.583,0.167 10 false PGND 0.688,1.875 1,2.042 0.313,0.167 10 false A15 0.792,3.396 1.104,3.563 0.313,0.167 10 false A14

Disconnect the A14 and A15 power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A15-6 (IG) - Body ground Ignition switch ON 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A14-2 (PGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
a.
U146983E02
1.813,1.125 2.031,1.125 true 1.813,1.469 2.031,1.469 true 0.24,0.177 0.531,0.333 0.292,0.156 10 false *a 2.073,1.052 2.396,1.208 0.323,0.156 10 false PIG 2.073,1.385 2.594,1.542 0.521,0.156 10 false PGND 0.802,0.958 1.094,1.115 0.292,0.156 10 false A14

Disconnect the A14 power steering ECU assembly connector .


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A14-1 (PIG) - Body ground Always 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A14-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR