Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

According to the display on the GTS, read the Data List.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from skid control ECU/
Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph) The vehicle is stopped.
No significant fluctuation The vehicle is driven at a constant speed.
Engine Revolution Engine speed/
Min.: 0 rpm
Max.: 12800 rpm
No significant fluctuation The engine is running at a constant speed.
Motor Actual Current Amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
Command Value Current Demanded amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
Steering Angle Velocity Steering angle speed/
Min.: -32768 deg/s
Max.: 32767 deg/s
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
Thermistor Temperature ECU substrate temperature/
Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
- The ignition switch is ON.
PIG Power Supply Power source voltage to active motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V The engine is running and power steering is operating.
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V The ignition switch is ON.
Steering Wheel Torque Steering wheel torque/
Min.: -7.00 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
Motor Rotation Angle Motor rotation angle/
Min.: 0.000 deg
Max.: 360.000 deg
Motor rotation angle value changes from 0 to 360° The engine is running and the steering wheel is being turned.
Command Val Current 2 Demanded amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
PIG2 Voltage Coil rear pressurization voltage/
Min.: 0.000 V
Max.: 98.000 V
Approximately 27 V The engine is running and the steering wheel is not being turned.
Value changes between 16 and 35 V The engine is running and the steering wheel is being turned.
Motor Voltage Motor power supply voltage/
Min.: 0.000 V
Max.: 98.000 V
Approximately 27 V The engine is running and the steering wheel is not being turned.
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.
Motor Terminal Volt(U) Motor terminal voltage (U phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.
Motor Terminal Volt(V) Motor terminal voltage (V phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.
Motor Terminal Volt(W) Motor terminal voltage (W phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.
Torque Sensor 1 Output Torque sensor 1 output voltage/
Min.: 0.0000 V
Max.: 5.0000 V
2.3 to 2.7 V The engine is running and the steering wheel is not turned (without load).
2.3 to 3.8 V The engine is running and the steering wheel is turned to the right when the vehicle is stopped.
1.2 to 2.7 V The engine is running and the steering wheel is turned to the left when the vehicle is stopped.
Torque Sensor 2 Output Torque sensor 2 output voltage/
Min.: 0.0000 V
Max.: 5.0000 V
2.3 to 2.7 V The engine is running and the steering wheel is not turned (without load).
1.2 to 2.7 V The engine is running and the steering wheel is turned to the right when the vehicle is stopped.
2.3 to 3.8 V The engine is running and the steering wheel is turned to the left when the vehicle is stopped.
TRQ1 Zero Point Value Torque sensor 1 zero point voltage/
Min.: 0.0000 V
Max.: 5.0000 V
Values differ depending on vehicle The engine is running and the steering wheel is not being turned.
TRQ2 Zero Point Value Torque sensor 2 zero point voltage/
Min.: 0.0000 V
Max.: 5.0000 V
Values differ depending on vehicle The engine is running and the steering wheel is not being turned.
IG ON/OFF Times Number of times ignition switch turned to ON/off after fail detection/
Min.: 0 times
Max.: 65535 times
- This value indicates the number of times the ignition switch is turned to ON and off after the latest DTC detection.
Motor Overheat Record Continuous overheat prevention control record/
Unrec or Rec
Unrec -
Motor Lo Power Record PIG power supply voltage drop record/
Unrec or Rec
Unrec -
Eng Rev Inter Record Record of engine speed interruption/
Unrec or Rec
Unrec -
Spd Sig Invalid Record Record of vehicle speed signal invalid/
Unrec or Rec
Unrec -
Battery Voltage Lo Record Battery voltage reduction history/
Min.: 0 times, Max.: 65535 times
0 to 65535 -
The Number of DTCs Number of stored DTCs when freeze frame data stored/
Min.: 0
Max.: 255
0 to 255 -