Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly determines whether the ignition switch status is ON or off through the IG power supply circuit.

DTC Code DTC Detection Condition Trouble Area
C1551 An IG power supply circuit malfunction inside the ECU
·

ECU IG1 fuse

·

IG power supply circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C113532E86
0.708,1.031 1.802,1.177 1.094,0.146 10 false from IG1 Circuit 2.938,1.229 3.552,1.427 0.615,0.198 10 false ECU IG1 4.448,1.042 4.74,1.208 0.292,0.167 10 false A15 4.813,1.042 4.979,1.188 0.167,0.146 10 false IG 4.531,0.833 4.625,0.979 0.094,0.146 10 false 6 4.448,2.146 4.719,2.292 0.271,0.146 10 false A14 4.813,2.146 5.24,2.292 0.427,0.146 10 false PGND 4.531,1.938 4.625,2.083 0.094,0.146 10 false 2 4.615,2.958 6.615,3.198 2,0.24 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly is replaced with a new one, perform rotation angle sensor initialization and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V The ignition switch is ON.

OK:

The normal condition value is displayed the GTS.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
a.
U146982E04
2.188,1.979 2.417,1.958 true 1.875,4.01 2.188,4.01 true 0.24,0.115 0.438,0.281 0.198,0.167 10 false *a 2.458,1.854 2.771,2.021 0.313,0.167 10 false IG 2.229,3.927 2.813,4.094 0.583,0.167 10 false PGND 0.688,1.875 1,2.042 0.313,0.167 10 false A15 0.792,3.396 1.104,3.563 0.313,0.167 10 false A14

Disconnect the A14 and A15 power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A15-6 (IG) - Body ground Ignition switch ON 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A14-2 (PGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR