Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552  PIG Power Supply Voltage Malfunction  


DESCRIPTION

When a problem occurs in the power steering system, the power supply relay circuit is shut off to stop the power assist.

DTC Code DTC Detection Condition Trouble Area
C1552 A PIG power supply circuit malfunction inside the ECU
·

EPS fuse

·

PIG power supply circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C261871E02
2.521,0.917 3.396,1.115 0.875,0.198 10 false EPS 4.25,0.646 4.406,0.802 0.156,0.156 10 false 1 4.25,2.094 4.406,2.25 0.156,0.156 10 false 2 4.458,0.75 5.313,0.938 0.854,0.188 10 false PIG 4.458,2.177 5.25,2.365 0.792,0.188 10 false PGND 0.521,0.74 1.802,1.073 1.281,0.333 10 false from Battery 4.167,3.115 7.031,3.479 2.865,0.365 10 false Power Steering ECU Assembly 4.177,2.969 4.802,3.146 0.625,0.177 10 false A14

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly is replaced with a new one, perform rotation angle sensor initialization and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (PIG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to active motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V The engine is running and power steering is operating.

OK:

The normal condition value is displayed the GTS.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)
a.
U146983E02
1.813,1.125 2.031,1.125 true 1.813,1.469 2.031,1.469 true 0.24,0.177 0.531,0.333 0.292,0.156 10 false *a 2.073,1.052 2.396,1.208 0.323,0.156 10 false PIG 2.073,1.385 2.594,1.542 0.521,0.156 10 false PGND 0.802,0.958 1.094,1.115 0.292,0.156 10 false A14

Disconnect the A14 power steering ECU assembly connector .


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A14-1 (PIG) - Body ground Always 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A14-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR