Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM2090E _55 Steering _060690 STEERING COLUMN _0297645 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING WHEEL OFF CENTER ADJUSTMENT PROCEDURE

a.

Inspect steering wheel off center.

i.

Turn the steering wheel to the center position.


ii.
C263369E02
0.958,0.323 1.656,0.323 true 0.979,1.156 1.771,1.156 true 0.979,0.729 2.115,0.729 true 2.052,0.875 1.25,0.875 1.25,0.875 1.25,0.74 true 0.76,0.24 0.948,0.396 0.188,0.156 10 false *1 0.781,1.083 0.969,1.24 0.188,0.156 10 false *2 0.781,0.635 0.969,0.792 0.188,0.156 10 false *a

Apply masking tape to the top center of the steering wheel and upper steering column cover.

Text in Illustration
*1 Steering Wheel
*2 Upper Steering Column Cover
*a Masking Tape


iii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), while holding the steering wheel to maintain the course.


iv.
C263370E02
0.99,0.375 1.698,0.375 true 0.99,0.646 2.26,0.646 true 2.26,0.906 1.333,0.906 1.333,0.906 1.333,0.656 true 1.01,1.073 1.594,1.073 true 0.792,0.302 0.979,0.458 0.188,0.156 10 false *1 0.802,0.99 0.99,1.146 0.188,0.156 10 false *2 0.792,0.583 0.979,0.74 0.188,0.156 10 false *a

Draw a line on the masking tape as shown in the illustration.

Text in Illustration
*1 Upper Steering Column Cover
*2 Steering Wheel
*a Marked Line


v.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



vi.
C263371E02
1.021,0.302 1.802,0.302 true 1.021,0.594 2.281,0.594 true 2.281,0.833 1.354,0.833 1.354,0.833 1.354,0.604 true 1.021,0.99 1.677,0.99 true 0.833,0.219 1.021,0.375 0.188,0.156 10 false *1 0.833,0.51 1.021,0.667 0.188,0.156 10 false *a 0.844,0.906 1.031,1.063 0.188,0.156 10 false *2

Draw a new line on the masking tape on the steering wheel as shown in the illustration.

Text in Illustration
*1 Upper Steering Column Cover
*2 Steering Wheel
*a Marked Line


vii.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


viii.

Convert the measured distance to steering angle.

HINT:
·

Measured distance 1 mm (0.0394 in.) = Steering angle of approximately 1 degree.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C182153E03
0.469,0.979 0.563,0.396 0.563,0.396 1,0.396 true 0.667,1.01 0.75,0.396 true 1.052,0.323 1.302,0.49 0.25,0.167 10 false *1

Put matchmarks on both sides of the tie rod assembly and steering rack end sub-assembly respectively.

Text in Illustration
*1 Matchmark


ii.

Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

HINT:
·

Measure both RH and LH sides.

·

Make a note of the measured values.




iii.
C181968

Remove the steering rack boot clips from both sides of the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle.

HINT:

One 360 degree turn of rack end (1.5 mm (0.0591 in.) horizontal movement) equals to 12 degrees of steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
85 N*m (869 kgf*cm, 63 ft.*lbf)

NOTICE:

Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH boot clips.