Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM2090E _55 Steering _060690 STEERING COLUMN _0297646 STEERING COLUMN ASSEMBLY G

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

When using a vise, do not overtighten it.


PROCEDURE

Hide 1.INSPECT PRELOAD

a.
C264009E03
2.031,1.948 2.615,1.948 true 2.656,1.854 2.885,2.042 0.229,0.188 10 false *1

Secure the steering column assembly in a vice using aluminum plates and wooden block as shown in the illustration.

Text in Illustration
*1 Wooden Block

NOTICE:
·

Do not overtighten the vice, as the steering column assembly may become deformed.

·

Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.




b.
C220801E02
0.815,1.529 0.964,1.681 0.149,0.152 10 *1 1.585,1.264 1.585,1.617 1.585,1.617 0.991,1.617 false 1.401,1.34 1.401,1.617 false

Install the 2 service nuts to the steering main shaft.

Text in Illustration
*1 Service Nut

Recommended service nut:
Thread diameter:

12.0 mm (0.472 in.)

Thread pitch:

1.25 mm (0.0492 in.)



c.

Tighten the 2 service nuts each other to lock them.

NOTICE:

Do not apply excess torque to the service nuts by using a tool such as an impact wrench.


HINT:

These nuts are installed to turn the steering main shaft. They should be removed after inspecting the steering main shaft rotating torque.



d.
C264010

Using a torque wrench, turn the main shaft and measure the preload.

Preload:

1.6 to 2.1 N*m (16.3 to 21.4 kgf*cm, 14.2 to 18.6 in.*lbf)


If the preload is not as specified, replace the steering column assembly with a new one.


Hide 2.INSPECT STEERING LOCK OPERATION (w/o Entry and Start System)

a.
C239701

Check that the steering lock mechanism is activated when the key is removed.


b.
C239702E01
2.104,0.873 2.257,1.023 0.153,0.15 10 *a 1.835,0.317 1.998,0.462 0.163,0.145 10 *b

Check that the steering lock mechanism is deactivated when the key is inserted and turned to the ACC position.

Text in Illustration
*a LOCK
*b ACC

HINT:

If there is any abnormality, replace the ignition switch lock cylinder assembly or steering column upper bracket assembly.



Hide 45250 3.INSPECT STEERING COLUMN ASSEMBLY

a.
C260481E02
0.563,1.938 0.958,1.938 0.958,1.938 0.958,1.719 true 2.969,1.938 2.573,1.938 2.573,1.938 2.573,1.719 true 0.396,1.865 0.583,2.021 0.188,0.156 10 false *1 3.01,1.854 3.198,2.01 0.188,0.156 10 false *1

Check that the 2 capsules are securely installed to the steering column assembly as shown in the illustration.

OK:

5.0 mm (0.1969 in.) or more


Text in Illustration
*1 Capsule

If the capsules are not positioned as specified, replace the steering column assembly with a new one.


b.

Check the 2 capsules for deformation and damage.

If either of the capsules is deformed, loose, missing or damaged, replace the steering column assembly with a new one.


Hide 45260 4.INSPECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Check for play

i.
C257765

Check that there is no play at the universal joint.

OK:

No play


HINT:

If the result is not as specified, replace the steering intermediate shaft assembly with a new one.




b.

Turning toque

i.
C257766

Hold the steering intermediate shaft assembly in a vise with the yoke on the rack and pinion power steering gear assembly side facing upward.


ii.

Using a push and pull gauge, measure the turning torque in the both directions.

Torque:

6.6 N*m (66 kgf*cm, 58 in.*lbf) or less


HINT:

If the result is not as specified, replace the steering intermediate shaft assembly with a new one.



iii.

Hold the steering intermediate shaft assembly in a vise with the yoke on the steering column assembly side facing upward.


iv.

Using a push and pull gauge, measure the turning torque in the both directions.

Torque:

6.0 N*m (61 kgf*cm, 53 in.*lbf) or less


HINT:

If the result is not as specified, replace the steering intermediate shaft assembly with a new one.