Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM2090E _55 Steering _060690 STEERING COLUMN _0297646 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, do not overtighten it.

·

Do not drop the steering column assembly, strike it with tools or subject it to impacts.

·

If the steering column assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the steering column assembly.

·

Do not allow any moisture to come into contact with the steering column assembly.

·

Do not loosen any bolts not mentioned in the procedure.



PROCEDURE

Hide 45020 1.REMOVE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Entry and Start System)

a.

Using a center punch, mark the center of the 2 tapered-head bolts.


b.

Using a 3 to 4 mm (0.118 to 0.157 in.) diameter drill bit, drill a hole in each tapered-head bolt.


c.
C234883

Using a screw extractor, remove each tapered-head bolt, and then remove the steering column upper with switch bracket assembly from the steering column assembly.


Hide 45020A 2.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

a.

Using a center punch, mark the center of the 2 tapered-head bolts.


b.

Using a 3 to 4 mm (0.118 to 0.157 in.) diameter drill bit, drill a hole in each tapered-head bolt.


c.
C234885

Using a screw extractor, remove each tapered-head bolt, and then remove the steering lock actuator assembly from the steering column assembly.


Hide 89783 3.REMOVE TRANSPONDER KEY AMPLIFIER (w/o Entry and Start System)

a.
C260478

Slide the transponder key amplifier, disengage the 2 claws and then remove the transponder key amplifier as shown in the illustration.


Hide 4.REMOVE UN-LOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C232527

Insert the key.


b.

Disengage the 2 claws and slide the un-lock warning switch assembly to remove it as shown in the illustration.


Hide 5.REMOVE KEY INTERLOCK SOLENOID (for Automatic Transmission without Entry and Start System)

a.
C260476

Remove the 2 screws and the key interlock solenoid from the steering column upper bracket assembly.


b.

Disengage the clamp.


Hide 69570 6.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.
C239344E01
1.59,1.942 1.757,2.086 0.167,0.144 10 *a 1.315,1.426 1.482,1.571 0.167,0.144 10 *b

Turn the ignition switch lock cylinder assembly to the ACC position.

Text in Illustration
*a LOCK
*b ACC


b.
C241164E03
1.906,0.625 1.906,0.281 1.906,0.281 1.854,0.281 true 1.99,0.604 1.99,0.198 1.99,0.198 2.719,0.198 true 1.698,0.208 1.854,0.427 0.156,0.219 10 false *1 2.76,0.094 2.948,0.313 0.188,0.219 10 false *2

Insert a screwdriver into the hole of the steering column upper bracket assembly as shown in the illustration. Pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper bracket assembly.

Text in Illustration
*1 Claw
*2 Stopper
V100135

Push
V100136

Pull

NOTICE:

Make sure to pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper bracket assembly. Failure to do so will affect later work operations.



c.
C239345E02
1.26,2.344 1.26,2.844 true 1.198,2.333 1.198,2.667 1.198,2.667 0.74,2.667 true 2.802,2.344 2.802,2.677 2.802,2.677 2.281,2.677 true 2.927,2.417 2.927,2.792 true 1.177,2.875 1.323,3.021 0.146,0.146 10 false *1 0.542,2.583 0.698,2.729 0.156,0.146 10 false *2 2.844,2.802 2.99,3 0.146,0.198 10 false *a 2.125,2.594 2.292,2.823 0.167,0.229 10 false *b

Insert a screwdriver into the hole of the steering column upper bracket assembly. Tilt the screwdriver as shown in the illustration to disengage the claw of the ignition switch lock cylinder assembly, and pull out the ignition switch lock cylinder assembly from the steering column upper bracket assembly.

Text in Illustration
*1 Claw
*2 Stopper
*a Claw disengaged
*b Driver Insertion Hole
V100135

Tilt
V100136

Pull out


Hide 84450 7.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C260475

Remove the 2 screws and the ignition or starter switch assembly from the steering column upper bracket assembly.