Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM2090E _55 Steering _060691 STEERING GEAR / LINKAGE _0297649 STEERING GEAR G

STEERING GEAR / LINKAGE  STEERING GEAR  INSPECTION  


PROCEDURE

Hide 45047 1.INSPECT TIE ROD END SUB-ASSEMBLY

a.

Secure the tie rod assembly in a vise.

NOTICE:

Do not overtighten the vise.



b.

Turn the ball joint back and forth.

OK:

There is no unusual resistance or play while turning.


HINT:
·

If the result is not as specified, remove the tie rod end sub-assembly with a new one.

·

If the dust seal is fissured, damaged or deteriorated, replace it with a new one.




Hide 2.INSPECT TOTAL PRELOAD

NOTICE:

Inspect the total preload in a no-load condition by removing the tie rod assembly RH and LH, and steering rack boots.


a.
C239563E01
2.895,1.396 3.206,1.553 0.311,0.157 10 SST 2.634,1.014 3.064,1.014 3.064,1.014 3.064,1.391 false

Install SST to the pinion shaft and turn it left and right 5 times or more.

SST
09616-00011  


b.

Set a torque wrench to SST and turn the pinion shaft continuously at a rate of 4 to 6 seconds per turn to inspect the total preload of the steering gear assembly.

Standard Preload:

0.9 to 1.6 N*m (9.2 to 16.3 kgf*cm, 8.0 to 14.2 in.*lbf)


NOTICE:

Inspect the total preload around the steering rack center position.


HINT:

If the total preload is not within the specified range, adjust the total preload.



Hide 3.ADJUST TOTAL PRELOAD

a.

Temporarily install the rack ends sub-assembly RH and LH.


b.

Install the steering rack guide and steering rack guide spring to the steering rack housing.


c.

Apply the three bond to the screw part of steering rack guide spring cap and steering rack housing.


d.

Temporally install the steering rack guide spring cap.


e.
C257758E03
1.26,0.938 0.427,0.938 0.427,0.938 0.927,0.323 true 0.094,0.865 0.385,1.042 0.292,0.177 10 false SST

Using SST, tighten the steering rack guide spring cap so that the rotational torque of the pinion shaft reaches the standard value.

SST
09631-10021  
09616-00011  

Torque: Preload (turning):

0.9 to 1.6 N*m (9.2 to 16.3 kgf*cm, 8.0 to 14.2 in.*lbf)



f.

Apply the three bond to the screw part of lock nut.


g.
C257759E01
2.336,0.258 2.727,0.470 0.391,0.212 10 SST 1.49,0.967 2.292,0.348 2.292,0.348 1.977,0.972 false

Using SST, hold the steering rack guide spring cap and tighten the lock nut.

SST
09631-10021  
09922-10010  

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where SST is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn SST in the direction as shown in the illustration.




h.

Set a torque wrench to SST and turn the pinion shaft continuously at a rate of 4 to 6 seconds per turn to inspect the total preload of the steering gear assembly.

SST
09616-00011  

Standard Preload:

0.9 to 1.6 N*m (9.2 to 16.3 kgf*cm, 8.0 to 14.2 in.*lbf)


NOTICE:

Inspect the total preload around the steering rack center position.