Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM2090E _56 Audio / Visual / Telematics _060692 AUDIO / VIDEO _0297650 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Speaker Circuit  


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.

If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

E177570E16
0.052,1.573 1.313,2.073 1.26,0.5 10 false Front No. 1 Speaker Assembly LH 0.042,3.906 1.271,4.302 1.229,0.396 10 false Front No. 1 Speaker Assembly RH 2.781,1.469 4.01,1.896 1.229,0.427 10 false Front No. 2 Speaker Assembly LH 2.781,3.823 4.042,4.365 1.26,0.542 10 false Front No. 2 Speaker Assembly RH 0.354,5.729 1.208,6.135 0.854,0.406 10 false Rear Speaker Assembly LH 0.417,7.125 1.26,7.604 0.844,0.479 10 false Rear Speaker Assembly RH 1.396,1.344 1.635,1.635 0.24,0.292 10 false 1 1.958,2 2.302,2.292 0.344,0.292 10 false 4 1.396,3.677 1.688,4.031 0.292,0.354 10 false 1 5.615,3.25 5.896,3.5 0.281,0.25 10 false 1 1.396,5.521 1.688,5.833 0.292,0.313 10 false 1 1.375,6.896 1.698,7.229 0.323,0.333 10 false 1 5.615,6.594 5.823,6.781 0.208,0.188 10 false 1 1.396,1.885 1.719,2.219 0.323,0.333 10 false 2 1.396,4.24 1.656,4.604 0.26,0.365 10 false 2 1.406,6.063 1.708,6.448 0.302,0.385 10 false 2 1.385,7.469 1.635,7.719 0.25,0.25 10 false 2 5.625,5.219 5.833,5.438 0.208,0.219 10 false 2 4.344,2 4.563,2.354 0.219,0.354 10 false 3 5.615,0.896 6,1.229 0.385,0.333 10 false 2 5.615,7.302 5.854,7.5 0.24,0.198 10 false 3 1.958,1 2.427,1.344 0.469,0.344 10 false 2 4.344,0.99 4.573,1.25 0.229,0.26 10 false 1 2.135,3.354 2.5,3.667 0.365,0.313 10 false + 2.156,4.563 2.646,4.865 0.49,0.302 10 false - 2.135,1 2.5,1.177 0.365,0.177 10 false + 2.156,2.188 2.448,2.458 0.292,0.271 10 false - 5.625,4.25 6,4.594 0.375,0.344 10 false 5 5.615,1.875 5.875,2.167 0.26,0.292 10 false 6 5.615,5.938 5.969,6.229 0.354,0.292 10 false 6 5.906,1.146 6.333,1.5 0.427,0.354 10 false FL+ 5.906,2.135 6.344,2.448 0.438,0.313 10 false FL- 5.906,3.49 6.458,3.906 0.552,0.417 10 false FR+ 5.906,4.49 6.302,4.802 0.396,0.313 10 false FR- 5.906,5.479 6.281,5.771 0.375,0.292 10 false RL+ 5.906,6.167 6.375,6.521 0.469,0.354 10 false RL- 5.906,6.833 6.313,7.156 0.406,0.323 10 false RR+ 5.906,7.521 6.365,7.802 0.458,0.281 10 false RR- 5.542,1.115 5.969,1.427 0.427,0.313 10 false D14 5.542,3.479 6.083,3.875 0.542,0.396 10 false D14 5.542,4.479 5.958,4.729 0.417,0.25 10 false D14 5.542,2.115 6.063,2.51 0.521,0.396 10 false D14 5.542,5.448 6,5.719 0.458,0.271 10 false D13 5.542,6.146 6.135,6.479 0.594,0.333 10 false D13 5.542,6.823 6.031,7.167 0.49,0.344 10 false D13 5.542,7.531 6,7.802 0.458,0.271 10 false D13 0.052,1.417 0.625,1.719 0.573,0.302 10 false E6 0.052,3.74 0.552,4.094 0.5,0.354 10 false F9 0.354,5.563 0.833,5.813 0.479,0.25 10 false H24 0.417,6.948 0.823,7.26 0.406,0.313 10 false G15 2.792,1.313 3.104,1.51 0.313,0.198 10 false D66 2.781,3.656 3.198,3.948 0.417,0.292 10 false D36 5.917,8.063 6.844,8.438 0.927,0.375 10 false Radio Receiver Assembly 4.333,3.365 4.625,3.771 0.292,0.406 10 false 1 1.948,3.354 2.24,3.75 0.292,0.396 10 false 2 4.344,4.354 4.563,4.823 0.219,0.469 10 false 3 1.958,4.375 2.219,4.938 0.26,0.563 10 false 4 4.125,1 4.49,1.177 0.365,0.177 10 false + 4.146,2.188 4.438,2.458 0.292,0.271 10 false - 4.125,3.354 4.49,3.667 0.365,0.313 10 false + 4.146,4.563 4.635,4.865 0.49,0.302 10 false -

PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Disconnect the connectors from the radio receiver assembly and speakers.


b.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
D14-1 (FR+) - D39-4 (+) Always Below 1 Ω
D14-5 (FR-) - D39-2 (-) Always Below 1 Ω
D14-2 (FL+) - D66-4 (+) Always Below 1 Ω
D14-6 (FL-) - D66-2 (-) Always Below 1 Ω



c.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
D66-3 (+) - E6-1 Always Below 1 Ω
D66-1 (-) - E6-2 Always Below 1 Ω
D39-3 (+) - F9-1 Always Below 1 Ω
D39-1 (-) - F9-2 Always Below 1 Ω



d.

Measure the resistance between each of the rear speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
D13-1 (RR+) - G15-1 Always Below 1 Ω
D13-3 (RR-) - G15-2 Always Below 1 Ω
D13-2 (RL+) - H24-1 Always Below 1 Ω
D13-6 (RL-) - H24-2 Always Below 1 Ω



e.

Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
D14-1 (FR+) - Body ground Always 10 kΩ or higher
D14-5 (FR-) - Body ground Always 10 kΩ or higher
D14-2 (FL+) - Body ground Always 10 kΩ or higher
D14-6 (FL-) - Body ground Always 10 kΩ or higher
D13-1 (RR+) - Body ground Always 10 kΩ or higher
D13-3 (RR-) - Body ground Always 10 kΩ or higher
D13-2 (RL+) - Body ground Always 10 kΩ or higher
D13-6 (RL-) - Body ground Always 10 kΩ or higher



f.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
D66-3 (+) - Body ground Always 10 kΩ or higher
D66-1 (-) - Body ground Always 10 kΩ or higher
D39-3 (+) - Body ground Always 10 kΩ or higher
D39-1 (-) - Body ground Always 10 kΩ or higher




OK

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
U190435E02
0.125,0.104 0.333,0.292 0.208,0.188 10 false *a 1.635,0.583 1.927,0.75 0.292,0.167 10 false E6 1.635,0.208 1.927,0.375 0.292,0.167 10 false F9 2.063,0.198 2.24,0.365 0.177,0.167 10 false *A 2.063,0.583 2.24,0.75 0.177,0.167 10 false *B

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E6-1 - E6-2 Always 3.4 to 4.6 Ω
F9-1 - F9-2 Always 3.4 to 4.6 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)




OK

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
U190436E02
1.323,1.75 0.99,2.375 true 1.646,1.75 1.49,2.375 true 2.146,1.75 2.51,2.396 true 1.865,1.75 2.063,2.375 true 0.115,0.115 0.271,0.26 0.156,0.146 10 false *a 1.917,0.531 2.156,0.708 0.24,0.177 10 false *A 1.917,0.865 2.156,1.042 0.24,0.177 10 false *B 1.51,0.531 1.792,0.698 0.281,0.167 10 false D39 1.5,0.885 1.781,1.052 0.281,0.167 10 false D66 1.438,2.396 1.594,2.542 0.156,0.146 10 false + 2.542,2.396 2.656,2.542 0.115,0.146 10 false - 2.073,2.396 2.188,2.542 0.115,0.146 10 false - 0.896,2.396 1.052,2.542 0.156,0.146 10 false +

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D39-1 (-) - D39-3 (+) Always 3.4 to 4.6 Ω
D39-4 (+) - D39-2 (-) Always 10 kΩ or higher
D39-3 (+)- D39-4 (+) Always Below 1 Ω
D39-1 (-) - D39-2 (-) Always Below 1 Ω
D66-1 (-) - D66-3 (+) Always 3.4 to 4.6 Ω
D66-4 (+) - D66-2 (-) Always 10 kΩ or higher
D66-3 (+) - D66-4 (+) Always Below 1 Ω
D66-1 (-) - D66-2 (-) Always Below 1 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)




OK

4.INSPECT REAR SPEAKER ASSEMBLY

NG

4.INSPECT REAR SPEAKER ASSEMBLY
a.
U190437E02
1.51,0.531 1.802,0.698 0.292,0.167 10 false H24 1.51,0.156 1.802,0.323 0.292,0.167 10 false G15 0.104,0.104 0.281,0.271 0.177,0.167 10 false *a 1.979,0.167 2.156,0.333 0.177,0.167 10 false *A 1.979,0.583 2.156,0.75 0.177,0.167 10 false *B

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-1 - H24-2 Always 5.1 to 6.9 Ω
G15-1 - G15-2 Always 5.1 to 6.9 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG