Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the ignition switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers the related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN NO. 1 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 1 junction connector.

HINT:

The following tables contain information about the items and buses connected via junction connectors. The junction connector may be used for multiple separate buses. In this case, the name of the bus will be shown below the name of the item that terminals are connected to. The bus name will be shown in brackets (example: (for V bus)).


i.

Connection diagram

U147021E02
3.01,0.302 3.406,1.25 true 3.385,1.531 2.958,2.385 true 4.281,0.51 3.885,1.25 true 3.865,1.531 4.292,2.271 true 4.135,0.281 3.729,1.229 true 3.729,1.542 4.135,2.479 true 3.177,0.125 3.563,1.24 true 3.542,1.521 3.177,2.542 true 0.115,0.094 0.323,0.292 0.208,0.198 10 false *a 2.833,0.229 3,0.406 0.167,0.177 10 false *b 2.792,2.344 2.948,2.531 0.156,0.188 10 false *b 4.333,0.406 4.51,0.583 0.177,0.177 10 false *e 4.323,2.24 4.479,2.427 0.156,0.188 10 false *e 4.167,0.177 4.333,0.333 0.167,0.156 10 false *d 4.156,2.479 4.333,2.656 0.177,0.177 10 false *d 3,0.021 3.146,0.208 0.146,0.188 10 false *c 3.042,2.563 3.208,2.74 0.167,0.177 10 false *c 2.063,1.313 2.333,1.479 0.271,0.167 10 false A17

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to TCM*
(for V bus)
*c to CAN No. 2 Junction Connector
(for V bus)
*d to ECM
(for V bus)
*e to Power Steering ECU Assembly
(for V bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. Wiring Color Connected to
A17-5 B-W TCM*
(for V bus)
A17-16 L
A17-6 W-B CAN No. 2 Junction Connector
(for V bus)
A17-17 R-Y
A17-7 O ECM
(for V bus)
A17-18 B-P
A17-8 B Power Steering ECU Assembly
(for V bus)
A17-19 W




* : for Automatic Transmission System

CAN NO. 1 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 1 junction connector.

i.

Connection diagram

U147021E02
3.01,0.302 3.406,1.25 true 3.385,1.531 2.958,2.385 true 4.281,0.51 3.885,1.25 true 3.865,1.531 4.292,2.271 true 4.135,0.281 3.729,1.229 true 3.729,1.542 4.135,2.479 true 3.177,0.125 3.563,1.24 true 3.542,1.521 3.177,2.542 true 0.115,0.094 0.323,0.292 0.208,0.198 10 false *a 2.833,0.229 3,0.406 0.167,0.177 10 false *b 2.792,2.344 2.948,2.531 0.156,0.188 10 false *b 4.333,0.406 4.51,0.583 0.177,0.177 10 false *e 4.323,2.24 4.479,2.427 0.156,0.188 10 false *e 4.167,0.177 4.333,0.333 0.167,0.156 10 false *d 4.156,2.479 4.333,2.656 0.177,0.177 10 false *d 3,0.021 3.146,0.208 0.146,0.188 10 false *c 3.042,2.563 3.208,2.74 0.167,0.177 10 false *c 2.063,1.313 2.333,1.479 0.271,0.167 10 false A17

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to TCM*
(for V bus
*c to Skid Control ECU (Brake Actuator Assembly)
(for V bus)
*d to CAN No. 2 Junction Connector
(for V bus)
*e to Power Steering ECU Assembly
(for V bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. Wiring Color Connected to
A17-5 B-W TCM*
(for V bus)
A17-16 L
A17-6 BR Skid Control ECU (Brake Actuator Assembly)
(for V bus)
A17-17 B-R
A17-7 W-B CAN No. 2 Junction Connector
(for V bus)
A17-18 R-Y
A17-8 B Power Steering ECU Assembly
(for V bus)
A17-19 W




* : for Automatic Transmission System

* : for Automatic Transmission System

CAN NO. 2 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 2 junction connector.

i.

Connection diagram

U190323E02
2.688,0.708 3.125,1.26 true 3.125,1.563 2.719,2.094 true 2.375,0.99 2.781,1.26 true 2.781,1.573 2.375,1.823 true 2.531,0.854 2.938,1.26 true 2.938,1.552 2.542,1.938 true 4.563,0.854 4.156,1.24 true 4.167,1.552 4.573,1.938 true 2.833,0.5 3.24,1.24 true 3.25,1.542 2.813,2.26 true 2.979,0.292 3.406,1.24 true 3.417,1.552 2.938,2.448 true 4.417,0.708 4.021,1.24 true 4.021,1.531 4.417,2.063 true 4.271,0.5 3.875,1.24 true 3.865,1.542 4.26,2.281 true 4.125,0.281 3.719,1.229 true 3.74,1.542 4.146,2.479 true 3.188,0.167 3.563,1.24 true 3.573,1.531 3.125,2.583 true 0.115,0.094 0.302,0.292 0.188,0.198 10 false *a 2.531,0.583 2.708,0.76 0.177,0.177 10 false *d 2.51,2.031 2.677,2.229 0.167,0.198 10 false *d 2.219,0.906 2.375,1.083 0.156,0.177 10 false *b 2.188,1.75 2.333,1.938 0.146,0.188 10 false *b 2.375,0.75 2.542,0.917 0.167,0.167 10 false *c 2.354,1.896 2.51,2.073 0.156,0.177 10 false *c 4.594,0.802 4.76,0.99 0.167,0.188 10 false *k 4.615,1.885 4.802,2.063 0.188,0.177 10 false *k 2.667,0.396 2.813,0.573 0.146,0.177 10 false *e 2.646,2.24 2.802,2.427 0.156,0.188 10 false *e 2.833,0.188 2.979,0.354 0.146,0.167 10 false *f 2.781,2.438 2.906,2.625 0.125,0.188 10 false *f 4.448,0.583 4.594,0.792 0.146,0.208 10 false *j 4.458,2.063 4.594,2.281 0.135,0.219 10 false *j 4.292,0.385 4.427,0.573 0.135,0.188 10 false *i 4.302,2.281 4.427,2.49 0.125,0.208 10 false *i 4.135,0.177 4.292,0.344 0.156,0.167 10 false *h 4.167,2.458 4.313,2.635 0.146,0.177 10 false *h 3.021,0.042 3.198,0.25 0.177,0.208 10 false *g 2.969,2.531 3.125,2.76 0.156,0.229 10 false *g 2.063,1.313 2.333,1.479 0.271,0.167 10 false D43

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Skid Control ECU (Brake Actuator Assembly)
(for V bus)
*c to Combination Meter Assembly
(for V bus)
*d to Main Body ECU (Network Gateway ECU)
(for V bus)
*e to Certification ECU (Smart Key ECU Assembly)*1
(for V bus)
*f to DLC3
(for V bus)
*g to Steering Angle Sensor (Spiral Cable Sub-assembly)
(for V bus)
*h to PSP (Option Connector)
(for V bus)
*i to Air Bag ECU Assembly
(for V bus)
*j to CAN No. 1 Junction Connector
(for V bus)
*k to Air Conditioning Control Assembly*2
(for V bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. Wiring Color Connected to
D43-1 W-B CAN No. 1 Junction Connector
(for V bus)
D43-12 R-Y
D43-2 BR Combination Meter Assembly
(for V bus)
D43-13 BR-W
D43-3 P Main Body ECU (Network Gateway ECU)
(for V bus)
D43-14 LG
D43-4 G Certification ECU (Smart Key ECU Assembly)*1
(for V bus)
D43-15 R
D43-5 B-Y DLC3
(for V bus)
D43-16 LG
D43-6 G-W Steering Angle Sensor (Spiral Cable Sub-assembly)
(for V bus)
D43-17 G
D43-7 P PSP (Option Connector)
(for V bus)
D43-18 L
D43-8 P-L Air Bag ECU Assembly
(for V bus)
D43-19 R-W
D43-9 O CAN No. 1 Junction Connector
(for V bus)
D43-20 B-P
D43-10 L-W Air Conditioning Control Assembly*2
(for V bus)
D43-21 L-Y




*1 : w/ Entry and Start System

*2 : for Automatic Air Conditioning System

CAN NO. 2 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 2 junction connector.

i.

Connection diagram

U190323E02
2.688,0.708 3.125,1.26 true 3.125,1.563 2.719,2.094 true 2.375,0.99 2.781,1.26 true 2.781,1.573 2.375,1.823 true 2.531,0.854 2.938,1.26 true 2.938,1.552 2.542,1.938 true 4.563,0.854 4.156,1.24 true 4.167,1.552 4.573,1.938 true 2.833,0.5 3.24,1.24 true 3.25,1.542 2.813,2.26 true 2.979,0.292 3.406,1.24 true 3.417,1.552 2.938,2.448 true 4.417,0.708 4.021,1.24 true 4.021,1.531 4.417,2.063 true 4.271,0.5 3.875,1.24 true 3.865,1.542 4.26,2.281 true 4.125,0.281 3.719,1.229 true 3.74,1.542 4.146,2.479 true 3.188,0.167 3.563,1.24 true 3.573,1.531 3.125,2.583 true 0.115,0.094 0.302,0.292 0.188,0.198 10 false *a 2.531,0.583 2.708,0.76 0.177,0.177 10 false *d 2.51,2.031 2.677,2.229 0.167,0.198 10 false *d 2.219,0.906 2.375,1.083 0.156,0.177 10 false *b 2.188,1.75 2.333,1.938 0.146,0.188 10 false *b 2.375,0.75 2.542,0.917 0.167,0.167 10 false *c 2.354,1.896 2.51,2.073 0.156,0.177 10 false *c 4.594,0.802 4.76,0.99 0.167,0.188 10 false *k 4.615,1.885 4.802,2.063 0.188,0.177 10 false *k 2.667,0.396 2.813,0.573 0.146,0.177 10 false *e 2.646,2.24 2.802,2.427 0.156,0.188 10 false *e 2.833,0.188 2.979,0.354 0.146,0.167 10 false *f 2.781,2.438 2.906,2.625 0.125,0.188 10 false *f 4.448,0.583 4.594,0.792 0.146,0.208 10 false *j 4.458,2.063 4.594,2.281 0.135,0.219 10 false *j 4.292,0.385 4.427,0.573 0.135,0.188 10 false *i 4.302,2.281 4.427,2.49 0.125,0.208 10 false *i 4.135,0.177 4.292,0.344 0.156,0.167 10 false *h 4.167,2.458 4.313,2.635 0.146,0.177 10 false *h 3.021,0.042 3.198,0.25 0.177,0.208 10 false *g 2.969,2.531 3.125,2.76 0.156,0.229 10 false *g 2.063,1.313 2.333,1.479 0.271,0.167 10 false D43

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
(for V bus)
*c to Combination Meter Assembly
(for V bus)
*d to Main Body ECU (Network Gateway ECU)
(for V bus)
*e to Certification ECU (Smart Key ECU Assembly)*1
(for V bus)
*f to DLC3
(for V bus)
*g to Steering Angle Sensor (Spiral Cable Sub-assembly)
(for V bus)
*h to PSP (Option Connector)
(for V bus)
*i to Air Bag ECU Assembly
(for V bus)
*j to ECM
(for V bus)
*k to Air Conditioning Control Assembly*2
(for V bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. Wiring Color Connected to
D43-1 W-B CAN No. 1 Junction Connector
(for V bus)
D43-12 R-Y
D43-2 BR Combination Meter Assembly
(for V bus)
D43-13 BR-W
D43-3 P Main Body ECU (Network Gateway ECU)
(for V bus)
D43-14 LG
D43-4 G Certification ECU (Smart Key ECU Assembly)*1
(for V bus)
D43-15 R
D43-5 B-Y DLC3
(for V bus)
D43-16 LG
D43-6 G-W Steering Angle Sensor (Spiral Cable Sub-assembly)
(for V bus)
D43-17 G
D43-7 P PSP (Option Connector)
(for V bus)
D43-18 L
D43-8 P-L Air Bag ECU Assembly
(for V bus)
D43-19 R-W
D43-9 O ECM
(for V bus)
D43-20 B-P
D43-10 L-W Air Conditioning Control Assembly*2
(for V bus)
D43-21 L-Y




*1 : w/ Entry and Start System

*2 : for Automatic Air Conditioning System

DLC3


a.
U147250E01
0.108,0.071 0.264,0.210 0.156,0.139 10 *a 1.542,0.298 1.837,0.454 0.295,0.156 10 D10 2.374,0.278 2.817,0.434 0.443,0.156 10 CANH 1.11,1.935 1.516,2.091 0.406,0.156 10 CANL 2.318,0.344 2.026,0.88 false 0.929,0.278 1.224,0.434 0.295,0.156 10 CG 1.255,0.344 1.547,0.88 false 1.905,1.477 1.613,2.013 false 2.734,1.798 3.029,1.954 0.295,0.156 10 BAT 2.381,1.477 2.673,1.875 false

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a DLC3

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D10-6 (CANH) - D10-14 (CANL) B-Y - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D10-6 (CANH) - D10-4 (CG) B-Y - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D10-14 (CANL) - D10-4 (CG) LG - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D10-6 (CANH) - D10-16 (BAT) B-Y - W-B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D10-14 (CANL) - D10-16 (BAT) LG - W-B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM


U147023E03
6.448,1.625 6.677,2.063 true 6.281,1.635 6.042,2.073 true 6.427,0.729 6.188,1.167 true 1.604,0.74 1.365,1.177 true 5.677,0.521 5.938,0.698 0.26,0.177 10 false A33 1.198,0.531 1.458,0.708 0.26,0.177 10 false A36 0.104,0.094 0.26,0.271 0.156,0.177 10 false *a 6.656,2.094 7.073,2.25 0.417,0.156 10 false CANL 5.625,2.031 6.042,2.188 0.417,0.156 10 false CANH 6.49,0.604 6.875,0.76 0.385,0.156 10 false BATT 1.635,0.625 1.927,0.781 0.292,0.156 10 false E01

Text in Illustration
*a Component without harness connected
(ECM)
- -

a.
U147156E01
1.489,0.391 1.784,0.547 0.295,0.156 10 A33 0.063,0.063 0.359,0.219 0.295,0.156 10 *a 1.489,2.413 1.784,2.569 0.295,0.156 10 A36 1.482,2.031 1.902,2.187 0.420,0.156 10 CANH 0.106,2.031 0.502,2.187 0.397,0.156 10 CANL 1.134,1.573 1.426,2.109 false 0.884,1.573 0.592,2.109 false 0.335,0.476 0.716,0.632 0.381,0.156 10 BATT 0.824,0.559 1.116,1.095 false 0.957,2.513 1.252,2.669 0.295,0.156 10 E01 1.288,2.596 1.58,3.132 false

Disconnect the A33 and A36 ECM connectors.

Text in Illustration
*a Front view of wire harness connector
(to ECM)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A33-19 (CANH) - A33-18 (CANL) O - B-P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 114 to 126 Ω
A33-19 (CANH) - A36-4 (E01) O - B-L HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A33-18 (CANL) - A36-4 (E01) B-P - B-L LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A33-19 (CANH) - A33-2 (BATT) O - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A33-18 (CANL) - A33-2 (BATT) B-P - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TCM (for Automatic Transmission System)


U147025E03
3.594,1.813 3.833,2.25 true 2.323,1.656 2.094,2.094 true 3.385,1.823 3.146,2.26 true 3.302,0.74 3.073,1.177 true 2.719,0.531 3.01,0.688 0.292,0.156 10 false A18 0.083,0.073 0.26,0.25 0.177,0.177 10 false *a 3.865,2.188 4.24,2.354 0.375,0.167 10 false CANL 2.729,2.198 3.146,2.354 0.417,0.156 10 false CANH 1.854,2.042 2.083,2.208 0.229,0.167 10 false BM 3.344,0.625 3.625,0.792 0.281,0.167 10 false E02

Text in Illustration
*a Component without harness connected
(TCM)
- -

a.
U147026E03
1.156,1.51 1.427,1.979 true 2.302,1.375 2.594,1.906 true 0.99,1.521 0.677,1.938 true 1.281,0.385 1.573,0.917 false 1.594,0.229 1.885,0.385 0.292,0.156 10 false A18 0.083,0.042 0.26,0.208 0.177,0.167 10 false *a 1.469,1.927 1.885,2.083 0.417,0.156 10 false CANH 0.344,1.927 0.719,2.104 0.375,0.177 10 false CANL 2.635,1.854 2.885,2.031 0.25,0.177 10 false BM 0.99,0.25 1.281,0.406 0.292,0.156 10 false E02

Disconnect the A18 TCM connector.

Text in Illustration
*a Front view of wire harness connector
(to TCM)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A18-29 (CANH) - A18-28 (CANL) B-W - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
A18-29 (CANH) - A18-3 (E02) B-W - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A18-28 (CANL) - A18-3 (E02) L - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A18-29 (CANH) - A18-26 (BM) B-W - Y-R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A18-28 (CANL) - A18-26 (BM) L - Y-R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


U147054E03
4.771,1.094 4.313,0.635 true 3.781,2.177 4.76,1.198 true 5.292,1.313 5.76,0.854 true 5.75,2.052 5.281,1.594 true 4.448,0.271 4.74,0.427 0.292,0.156 10 false A15 0.146,0.094 0.323,0.292 0.177,0.198 10 false *a 5.104,0.271 5.396,0.427 0.292,0.156 10 false A14 3.906,0.521 4.302,0.698 0.396,0.177 10 false CANH 5.844,0.781 6.125,0.958 0.281,0.177 10 false PIG 5.813,2.01 6.219,2.167 0.406,0.156 10 false PGND 3.406,2.135 3.781,2.302 0.375,0.167 10 false CANL

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

a.
U147157E03
1.281,1.229 0.927,0.875 true 0.938,1.875 1.292,1.521 true 1.531,3.281 1.167,2.917 true 1.177,4.042 1.542,3.688 true 1.573,0.417 1.865,0.573 0.292,0.156 10 false A15 0.104,0.073 0.281,0.26 0.177,0.188 10 false *a 1.573,2.448 1.865,2.604 0.292,0.156 10 false A14 0.49,0.771 0.906,0.927 0.417,0.156 10 false CANH 0.521,1.823 0.906,2 0.385,0.177 10 false CANL 0.854,2.833 1.135,3 0.281,0.167 10 false PIG 0.74,4.021 1.156,4.177 0.417,0.156 10 false PGND

Disconnect the A14 and A15 power steering ECU assembly connectors.

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A15-1 (CANH) - A15-7 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
A15-1 (CANH) - A14-2 (PGND) B - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A15-7 (CANL) - A14-2 (PGND) W - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A15-1 (CANH) - A14-1 (PIG) B - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A15-7 (CANL) - A14-1 (PIG) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


U147030E03
4.156,1.458 4.396,1.896 true 4.781,1.438 5.021,1.875 true 4.01,1.448 3.771,1.885 true 2.385,1.448 2.146,1.885 true 3.51,0.75 3.708,0.906 0.198,0.156 10 false D7 0.115,0.073 0.323,0.281 0.208,0.208 10 false *a 4.438,1.854 4.854,2.01 0.417,0.156 10 false CANH 3.396,1.875 3.781,2.031 0.385,0.156 10 false CANL 5.063,1.823 5.208,1.99 0.146,0.167 10 false B 1.875,1.896 2.167,2.073 0.292,0.177 10 false ES1

Text in Illustration
*a Component without harness connected
(Combination Meter Assembly)
- -

a.
U147033E03
1.281,1.135 1.573,1.667 true 0.792,0.51 0.5,1.042 true 1.104,1.135 0.813,1.667 true 2.615,0.5 2.906,1.042 true 1.615,0.292 1.844,0.469 0.229,0.177 10 false D7 0.073,0.052 0.26,0.24 0.188,0.188 10 false *a 1.604,1.604 2.021,1.76 0.417,0.156 10 false CANL 0.469,1.688 0.885,1.844 0.417,0.156 10 false CANH 0.844,0.365 1.01,0.531 0.167,0.167 10 false B 2.323,0.396 2.615,0.563 0.292,0.167 10 false ES1

Disconnect the D7 combination meter assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D7-6 (CANH) - D7-7 (CANL) BR - BR-W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D7-6 (CANH) - D7-20 (ES1) BR - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D7-7 (CANL) - D7-20 (ES1) BR-W - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D7-6 (CANH) - D7-1 (B BR - R-W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D7-7 (CANL) - D7-1 (B BR-W - R-W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)


U146881E01
0.39,1.189 0.585,1.345 0.195,0.156 10 3D 0.209,0.217 0.405,0.373 0.195,0.156 10 *a 1.891,6.634 2.086,6.790 0.195,0.156 10 *b 1.483,4.052 1.678,4.208 0.195,0.156 10 3D 3.758,1.063 3.984,1.219 0.226,0.156 10 MB 3.505,3.225 3.732,3.381 0.226,0.156 10 MB 6.354,1.147 6.544,1.303 0.190,0.156 10 3B 1.794,5.282 1.984,5.438 0.190,0.156 10 3B 6.355,1.805 6.543,1.962 0.188,0.156 10 3A 4.945,5.282 5.133,5.438 0.188,0.156 10 3A 0.39,1.761 0.585,1.917 0.195,0.156 10 3C 4.215,4.052 4.409,4.208 0.195,0.156 10 3C 0.394,2.383 0.581,2.539 0.187,0.156 10 3E 6.254,4.052 6.441,4.208 0.187,0.156 10 3E 3.049,6.539 3.315,6.695 0.266,0.156 10 A73 1.115,7.493 1.382,7.649 0.266,0.156 10 A73 3.722,6.539 3.920,6.695 0.198,0.156 10 D5 3.596,7.493 3.794,7.649 0.198,0.156 10 D5 4.236,6.539 4.430,6.695 0.195,0.156 10 D6 5.917,7.493 6.112,7.649 0.195,0.156 10 D6 3.889,8.573 4.309,8.729 0.421,0.156 10 CANL 2.805,8.573 3.228,8.729 0.423,0.156 10 CANH 3.605,8.199 3.843,8.636 false 3.47,8.199 3.232,8.636 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Main Body ECU (Network Gateway ECU))

a.
U147158E03
1.271,2.594 1.563,3.125 true 2.5,3.813 2.792,4.208 true 1.927,1.177 2.219,1.708 true 1.802,1.177 1.51,1.708 true 1.594,0.26 1.802,0.438 0.208,0.177 10 false D5 0.083,0.052 0.25,0.24 0.167,0.188 10 false *a 0.115,2.448 0.292,2.625 0.177,0.177 10 false *1 1.531,2.521 1.823,2.677 0.292,0.156 10 false D10 1.031,2.49 1.26,2.667 0.229,0.177 10 false CG 2.844,4.198 3.135,4.354 0.292,0.156 10 false BAT 1.146,1.667 1.521,1.844 0.375,0.177 10 false CANL 2.25,1.667 2.667,1.823 0.417,0.156 10 false CANH

Disconnect the D5 main body ECU (network gateway ECU) connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Main Body ECU (Network Gateway ECU))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D5-14 (CANH) - D5-13 (CANL) P - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D5-14 (CANH) - D10-4 (CG) P - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D5-13 (CANL) - D10-4 (CG) LG - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D5-14 (CANH) - D10-16 (BAT) P - W-B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D5-13 (CANL) - D10-16 (BAT) LG - W-B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


U190183E02
4.823,1.542 5.063,2.115 true 4.708,1.542 4.479,2.115 true 1.302,0.875 1.542,1.313 true 2.542,1.688 2.781,2.156 true 4.844,0.771 5.135,0.927 0.292,0.156 10 false D41 1.917,0.771 2.208,0.927 0.292,0.156 10 false D48 0.104,0.063 0.396,0.219 0.292,0.156 10 false *a 5.115,2.094 5.531,2.25 0.417,0.156 10 false CANH 4.073,2.104 4.458,2.281 0.385,0.177 10 false CANL 1.083,0.792 1.292,0.958 0.208,0.167 10 false +B 2.833,2.094 3.167,2.25 0.333,0.156 10 false GND

Text in Illustration
*a Component without harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

a.
U190420E01
1.563,0.357 1.859,0.513 0.295,0.156 10 D41 0.089,0.078 0.384,0.234 0.295,0.156 10 *a 1.563,2.636 1.859,2.792 0.295,0.156 10 D48 2.662,1.846 3.082,2.002 0.420,0.156 10 CANL 0.863,1.846 1.283,2.002 0.420,0.156 10 CANH 0.399,3.085 0.819,3.242 0.420,0.156 10 GND 2.089,1.398 2.629,1.931 false 1.37,1.931 1.91,1.398 false 2.722,2.721 3.142,2.877 0.420,0.156 10 +B 1.142,3.659 0.823,3.169 false 2.342,3.297 2.661,2.807 false

Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D41-14 (CANH) - D41-15 (CANL) G - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D41-14 (CANH) - D48-11 (GND) G - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D41-15 (CANL) - D48-11 (GND) R - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D41-14 (CANH) - D48-2 (+B) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D41-15 (CANL) - D48-2 (+B) R - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)


U147056E01
3.664,0.253 3.959,0.410 0.295,0.156 10 D56 4.361,1.276 4.757,1.432 0.396,0.156 10 CANL 2.963,1.276 3.383,1.432 0.420,0.156 10 CANH 0.105,0.071 0.400,0.228 0.295,0.156 10 *a 3.953,0.964 4.324,1.336 false 3.755,0.964 3.383,1.336 false

Text in Illustration
*a Component without harness connected
(Steering Angle Sensor (Spiral Cable Sub-assembly))
- -

a.
U147159E03
1.354,1.448 1.031,1.76 false 1.635,1.448 1.958,1.76 false 1.26,2.594 1.552,3.125 true 2.5,3.823 2.792,4.219 true 1.469,0.792 1.76,0.948 0.292,0.156 10 false D56 1.99,1.698 2.417,1.854 0.427,0.156 10 false CANH 0.604,1.74 1.031,1.896 0.427,0.156 10 false CANL 0.104,0.083 0.302,0.271 0.198,0.188 10 false *a 0.104,2.344 0.281,2.531 0.177,0.188 10 false *1 1.49,2.531 1.781,2.688 0.292,0.156 10 false D10 1,2.479 1.229,2.635 0.229,0.156 10 false CG 2.854,4.177 3.146,4.333 0.292,0.156 10 false BAT

Disconnect the D56 steering angle sensor (spiral cable sub-assembly) connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D56-3 (CANH) - D56-2 (CANL) G-W - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D56-3 (CANH) - D10-4 (CG) G-W - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D56-2 (CANL) - D10-4 (CG) G - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D56-3 (CANH) - D10-16 (BAT) G-W - W-B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D56-2 (CANL) - D10-16 (BAT) G - W-B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




PSP (OPTION CONNECTOR)


U147160E03
1.875,1.51 2.219,2.063 true 1.458,1.531 1.125,2.052 true 1.25,2.594 1.542,3.125 true 2.531,3.823 2.823,4.219 true 1.552,2.5 1.844,2.656 0.292,0.156 10 false D10 1.531,0.667 1.813,0.833 0.281,0.167 10 false D29 0.083,0.073 0.271,0.26 0.188,0.188 10 false *a 0.083,2.344 0.24,2.521 0.156,0.177 10 false *1 2.26,1.979 2.677,2.135 0.417,0.156 10 true CANL 0.604,1.979 1.031,2.135 0.427,0.156 10 false CANH 0.979,2.49 1.219,2.646 0.24,0.156 10 false CG 2.885,4.177 3.177,4.333 0.292,0.156 10 false BAT

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to PSP (Option Connector))

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D29-4 (CANH) - D29-5 (CANL) P - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D29-4 (CANH) - D10-4 (CG) P - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D29-5 (CANL) - D10-4 (CG) L - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D29-4 (CANH) - D10-16 (BAT) P - W-B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D29-5 (CANL) - D10-16 (BAT) L - W-B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR BAG ECU ASSEMBLY


U147122E01
2.374,0.389 2.670,0.545 0.295,0.156 10 D27 3.691,2.259 4.105,2.416 0.413,0.156 10 CANL 1.814,2.259 2.227,2.416 0.413,0.156 10 CANH 0.126,0.066 0.422,0.222 0.295,0.156 10 *a 2.94,1.624 2.243,2.321 false 3.295,1.977 3.639,2.321 false

Text in Illustration
*a Component without harness connected
(Air Bag ECU Assembly)
- -

a.
U147161E03
1.344,1.479 2.198,2.333 true 1.042,1.875 0.625,2.302 true 1.229,2.563 1.521,3.094 true 2.531,3.813 2.823,4.208 true 1.563,0.323 1.854,0.479 0.292,0.156 10 false D27 1.583,2.542 1.875,2.698 0.292,0.156 10 false D10 0.198,2.25 0.615,2.406 0.417,0.156 10 false CANL 2.25,2.25 2.667,2.406 0.417,0.156 10 false CANH 0.135,0.104 0.313,0.292 0.177,0.188 10 false *a 0.135,2.573 0.344,2.75 0.208,0.177 10 false *1 0.896,2.479 1.188,2.635 0.292,0.156 10 false CG 2.875,4.125 3.167,4.281 0.292,0.156 10 false BAT

Disconnect the D27 air bag ECU assembly connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Air Bag ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D27-13 (CANH) - D27-22 (CANL) P-L - R-W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D27-13 (CANH) - D10-4 (CG) P-L - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D27-22 (CANL) - D10-4 (CG) R-W - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D27-13 (CANH) - D10-16 (BAT) P-L - W-B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D27-22 (CANL) - D10-16 (BAT) R-W - W-B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


U190363E01
2.351,0.234 2.646,0.390 0.295,0.156 10 D19 3.855,0.257 4.150,0.413 0.295,0.156 10 +B 0.791,0.257 1.133,0.413 0.342,0.156 10 GND 0.072,0.066 0.367,0.222 0.295,0.156 10 *a 2.982,1.159 3.803,0.337 false 3.32,0.257 3.734,0.413 0.413,0.156 10 CANL 2.588,1.159 3.269,0.337 false 1.977,1.159 1.155,0.337 false 1.255,0.257 1.671,0.413 0.417,0.156 10 CANH 2.377,1.159 1.695,0.337 false

Text in Illustration
*a Component without harness connected
(Air Conditioning Control Assembly)
- -

a.
U190364E01
1.585,0.272 1.880,0.429 0.295,0.156 10 D19 0.382,1.458 0.677,1.614 0.295,0.156 10 +B 2.926,1.458 3.277,1.614 0.351,0.156 10 GND 0.078,0.06 0.374,0.217 0.295,0.156 10 *a 0.842,1.327 0.642,1.528 false 2.647,1.327 2.847,1.528 false 2.279,1.785 2.699,1.942 0.421,0.156 10 CANH 0.71,1.785 1.105,1.942 0.396,0.156 10 CANL 1.931,1.327 2.223,1.863 false 1.526,1.327 1.234,1.863 false

Disconnect the D19 air conditioning control assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D19-13 (CANH) - D19-12 (CANL) L-W - L-Y HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 57 to 63 Ω
D19-13 (CANH) - D19-16 (GND) L-W - B-Y HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D19-12 (CANL) - D19-16 (GND) L-Y - B-Y LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
D19-13 (CANH) - D19-9 (+B) L-W - L-R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D19-12 (CANL) - D19-9 (+B) L-Y - L-R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


U147123E03
4.635,1.271 5.208,1.625 true 4.552,0.885 4.958,0.229 true 5,0.76 5.656,0.354 true 2.198,0.76 1.531,0.333 true 1.385,0.927 1.604,1.083 0.219,0.156 10 false A5 4.99,0.115 5.385,0.281 0.396,0.167 10 false CANL 5.26,1.552 5.698,1.708 0.438,0.156 10 false CANH 0.094,0.052 0.26,0.25 0.167,0.198 10 false *a 5.708,0.26 6.063,0.438 0.354,0.177 10 false +BM 1.094,0.26 1.5,0.427 0.406,0.167 10 false GND2

Text in Illustration
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -

a.
U147124E03
0.76,0.958 1.167,0.552 true 1.281,0.781 0.979,1.094 true 2.031,0.323 2.667,0.958 true 1.167,1.615 0.885,1.344 true 0.177,1.094 0.396,1.271 0.219,0.177 10 false A5 1.583,0.24 2.031,0.396 0.448,0.156 10 false GND2 1.188,0.448 1.5,0.625 0.313,0.177 10 false +BM 1.313,0.677 1.75,0.833 0.438,0.156 10 false CANL 1.208,1.583 1.625,1.75 0.417,0.167 10 false CANH 0.125,0.083 0.302,0.26 0.177,0.177 10 false *a

Disconnect the A5 skid control ECU (brake actuator assembly) connector.

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A5-26 (CANH) - A5-14 (CANL) BR - B-R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 114 to 126 Ω
A5-26 (CANH) - A5-13 (GND2) BR - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A5-14 (CANL) - A5-13 (GND2) B-R - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A5-26 (CANH) - A5-1 (+BM) BR - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A5-14 (CAN_L) - A5-1 (+BM) B-R - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher