Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Bus Buffer ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Bus Buffer ECU Communication Stop Mode Communication system DTCs (DTCs that start with U) that are output correspond to "Bus Buffer ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)) PSP (option connector) branch line or connector

WIRING DIAGRAM

C261301E06
2.198,1.073 2.094,0.469 2.094,0.469 1.844,0.469 false 3.646,1.063 3.979,0.479 3.979,0.479 4.229,0.479 false 3.135,0.406 3.521,0.573 0.385,0.167 10 false DLC3 4.292,2.865 4.417,3.031 0.125,0.167 10 false 5 3.885,2.865 4.021,3.021 0.135,0.156 10 false 4 0.333,2.615 0.667,2.781 0.333,0.167 10 false ECM 0.854,1.979 1.208,2.167 0.354,0.188 10 false 120Ω 5.948,1.979 6.313,2.146 0.365,0.167 10 false 120Ω 1.427,5.063 3.219,5.24 1.792,0.177 10 false : CAN Main Bus Line (CANH) 1.427,5.375 3.208,5.542 1.781,0.167 10 false : CAN Main Bus Line (CANL) 4.385,5.073 6.063,5.25 1.677,0.177 10 false : CAN Branch Line (CANH) 4.385,5.375 6.021,5.563 1.635,0.188 10 false : CAN Branch Line (CANL) 0.438,0.417 1.823,0.76 1.385,0.344 10 false CAN NO. 1 JUNCTION CONNECTOR 4.292,0.427 5.719,0.781 1.427,0.354 10 false CAN NO. 2 JUNCTION CONNECTOR 5.573,2.615 6.927,3.135 1.354,0.521 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 3.115,4.563 4.938,4.729 1.823,0.167 10 false PSP (OPTION CONNECTOR) 3.115,4.385 3.375,4.542 0.26,0.156 10 false D29 3.615,3.083 4.021,3.24 0.406,0.156 10 false CANH 4.135,3.083 4.521,3.25 0.385,0.167 10 false CANL 5.542,3.854 6.375,4.042 0.833,0.188 10 false Trouble Area 0.073,0.031 0.75,0.219 0.677,0.188 12 false for RHD:

C261301E07
2.156,1.063 2.073,0.458 2.073,0.458 1.865,0.458 false 3.656,1.063 3.969,0.458 3.969,0.458 4.177,0.458 false 3.542,3.063 3.958,3.229 0.417,0.167 10 false CANH 4.104,3.063 4.521,3.229 0.417,0.167 10 false CANL 0.448,0.406 1.854,0.771 1.406,0.365 10 false CAN NO. 1 JUNCTION CONNECTOR 4.24,0.385 5.646,0.719 1.406,0.333 10 false CAN NO. 2 JUNCTION CONNECTOR 5.5,3.76 6.313,3.938 0.813,0.177 10 false Trouble Area 3.083,0.406 3.458,0.573 0.375,0.167 10 false DLC3 1.375,5.083 3.198,5.271 1.823,0.188 10 false : CAN Main Bus Line (CANH) 1.385,5.396 3.167,5.583 1.781,0.188 10 false : CAN Main Bus Line (CANL) 4.344,5.063 6.01,5.26 1.667,0.198 10 false : CAN Branch Line (CANH) 4.354,5.375 6,5.573 1.646,0.198 10 false : CAN Branch Line (CANL) 5.667,2.594 6.01,2.76 0.344,0.167 10 false ECM 3.104,4.542 4.927,4.729 1.823,0.188 10 false PSP (OPTION CONNECTOR) 0.25,2.625 2.167,3 1.917,0.375 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 0.813,1.969 1.208,2.146 0.396,0.177 10 false 120 Ω 5.906,1.979 6.302,2.156 0.396,0.177 10 false 120 Ω 3.875,2.854 4,3.021 0.125,0.167 10 false 4 4.281,2.854 4.417,3.01 0.135,0.156 10 false 5 3.094,4.365 3.354,4.531 0.26,0.167 10 false D29 0.063,0.01 0.698,0.219 0.635,0.208 12 false for LHD:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 2 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (PSP (OPTION CONNECTOR) BRANCH LINE)
a.
U147121E01
1.516,0.436 1.811,0.592 0.295,0.156 10 D29 0.065,0.04 0.361,0.196 0.295,0.156 10 *a 2.273,1.804 2.696,1.960 0.423,0.156 10 CANL 0.554,1.804 0.993,1.960 0.439,0.156 10 CANH 1.924,1.345 2.217,1.881 false 1.424,1.345 1.131,1.881 false

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D29-4 (CANH) - D29-5 (CANL) Cable disconnected from negative (-) battery terminal 57 to 63 Ω


Text in Illustration
*a Front view of wire harness connector
(to PSP (Option Connector))



OK

END

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (PSP (OPTION CONNECTOR))