Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297666 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is output when the LIN communication between the certification ECU (smart key ECU assembly) and the ID code box (immobiliser code ECU) stops for more than 10 seconds.

DTC No. DTC Detection Condition Trouble Area
B2789 No communication between the certification ECU (smart key ECU assembly) and the ID code box (immobiliser code ECU) for more than 10 seconds
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

E222997E12
6.104,0.74 6.833,0.927 0.729,0.188 10 false MAIN Fuse 1.51,0.99 1.75,1.167 0.24,0.177 10 false LIN 0.885,1.781 2.833,2.125 1.948,0.344 10 false CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 0.885,1.604 1.156,1.75 0.271,0.146 10 false D41 1.813,0.833 2.01,0.99 0.198,0.156 10 false 17 3.719,1.177 4.021,1.333 0.302,0.156 10 false GND 4.115,1.073 4.24,1.229 0.125,0.156 10 false 5 3.802,0.708 4.021,0.875 0.219,0.167 10 false +B 4.115,0.604 4.229,0.771 0.115,0.167 10 false 1 4.896,0.854 5.635,1.031 0.74,0.177 10 false AM2 NO. 2 0.844,2.385 2.469,2.573 1.625,0.188 10 false : LIN Communication Line 3.198,0.958 3.448,1.135 0.25,0.177 10 false LIN 3.146,1.781 4.927,2.135 1.781,0.354 10 false ID CODE BOX (IMMOBILISER CODE ECU) 3.167,1.604 3.448,1.781 0.281,0.177 10 false A30 2.99,0.823 3.125,0.99 0.135,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly), refer to the registration procedures for the Service Bulletin.

·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

·

Inspect the fuses for this circuit before starting this inspection procedure.



HINT:

When communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK DTC
2.CHECK DTC

Result
Result Proceed to
DTC B2789 is output A
DTC B2789 and B2785 is output B

HINT:

When both B2789 and B2785 are output at the same time, troubleshoot B2785 first.



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A30 ID code box (immobiliser code ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D41-17 (LIN) - A30-2 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D41-17 (LIN) or A30-2 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U190421E01
0.105,0.064 0.279,0.222 0.174,0.158 10 *a 0.785,1.448 0.990,1.606 0.205,0.158 10 +B 2.507,1.448 2.848,1.606 0.341,0.158 10 GND 1.335,1.249 1.053,1.53 false 2.158,1.249 2.44,1.53 false 1.57,0.217 1.866,0.374 0.295,0.156 10 A30

a.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
A30-1 (+B) - Body ground Always 11 to 14 V


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-5 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to ID Code Box (Immobiliser Code ECU))


OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

b.

Recheck for DTC.

Result
Result Proceed to
B2789 is not output A
B2789 is output B



A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)