89745A
1.REMOVE TRANSMITTER BATTERY (for Type A)
Take extra care when handling these precision electronic components.
Push the release hook knob and extract the mechanical key.
| *1 | Release Hook Knob |
| *2 | Mechanical Key |
Insert a precision screwdriver with its tip wrapped in protective tape and pry apart the transmitter housing cover.
| *1 | Protective Tape |
| *2 | Transmitter Housing Cover |
Insert a precision screwdriver with its tip wrapped in protective tape into the gap and gently remove the transmitter battery (lithium battery: CR1632).
| *1 | Protective Tape |
| *2 | Transmitter Battery |
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.
Do not push the terminals with your finger.
Do not forcibly pry up the transmitter battery. The terminals may be damaged.
Do not touch the transmitter battery with wet hands. Water may cause rust.
Do not touch or move any components inside the transmitter. It may interfere with proper operation.
2.REMOVE TRANSMITTER BATTERY (for Type B)
Take extra care when handling these precision electronic components.
Push the release hook knob and extract the mechanical key.
| *1 | Release Hook Knob |
| *2 | Mechanical Key |
Insert a precision screwdriver with its tip wrapped in protective tape and pry apart the transmitter housing cover.
| *1 | Protective Tape |
| *2 | Transmitter Housing Cover |
Remove the battery (lithium battery: CR2032).
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.
Do not push the terminals with your finger.
Do not forcibly pry up the transmitter battery. The terminals may be damaged.
Do not touch the transmitter battery with wet hands. Water may cause rust.
Do not touch or move any components inside the transmitter. It may interfere with proper operation.
89745A
3.REMOVE TRANSMITTER BATTERY (for Type C)
Take extra care when handling these precision electronic components.
Slide the release hook knob and extract the mechanical key.
| *1 | Release Hook Knob |
| *2 | Mechanical Key |
Insert a precision screwdriver with its tip wrapped in protective tape and pry apart the transmitter housing cover.
| *1 | Protective Tape |
| *2 | Transmitter Housing Cover |
Insert a precision screwdriver with its tip wrapped in protective tape into the gap and gently remove the transmitter battery (lithium battery: CR2032).
| *1 | Protective Tape |
| *2 | Transmitter Battery |
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.
Do not push the terminals with your finger.
Do not forcibly pry up the transmitter battery. The terminals may be damaged.
Do not touch the transmitter battery with wet hands. Water may cause rust.
Do not touch or move any components inside the transmitter. It may interfere with proper operation.
89745A
4.INSTALL TRANSMITTER BATTERY (for Type A)
Install a new transmitter battery (lithium battery: CR1632) with the positive (+) side facing upward, as shown in the illustration.
| *1 | Transmitter Battery |
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.
Do not bend the transmitter battery electrode during insertion.
Keep the transmitter cover interior free of dust and oil.
Install the transmitter housing cover by pressing down on it as shown in the illustration.
| *1 | Transmitter Housing Cover |
Insert the mechanical key into the transmitter.
| *1 | Mechanical Key |
Press one of the transmitter switches and check that the LED illuminates.
Transmitter LED illuminates when switch is pressed.
5.INSTALL TRANSMITTER BATTERY (for Type B)
Install a new transmitter battery (lithium battery: CR2032) with the positive (+) side facing upward, as shown in the illustration.
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.
Do not bend the transmitter battery electrode during insertion.
Keep the transmitter cover interior free of dust and oil.
Install the transmitter housing cover by pressing down on it as shown in the illustration.
| *1 | Transmitter Housing Cover |
Insert the mechanical key into the transmitter.
| *1 | Mechanical Key |
Press one of the transmitter switches and check that the LED illuminates.
Transmitter LED illuminates when switch is pressed.
89745A
6.INSTALL TRANSMITTER BATTERY (for Type C)
Install a new transmitter battery (lithium battery: CR2032) with the positive (+) side facing upward, as shown in the illustration.
| *1 | Transmitter Battery |
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.
Do not bend the transmitter battery electrode during insertion.
Keep the transmitter cover interior free of dust and oil.
Install the transmitter housing cover by pressing down on it as shown in the illustration.
| *1 | Transmitter Housing Cover |
Insert the mechanical key into the transmitter.
| *1 | Mechanical Key |
Press one of the transmitter switches and check that the LED illuminates.
Transmitter LED illuminates when switch is pressed.