Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL TRANSMITTER(w/ Entry and Start System) › 2012.03–2014.05
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297672 DOOR CONTROL TRANSMITTER(w/ Entry and Start System) G

DOOR LOCK  DOOR CONTROL TRANSMITTER(w/ Entry and Start System)  INSPECTION  


PROCEDURE

Hide 89904B 1.INSPECT ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

a.

Inspect operation of the transmitter.

i.

Remove the transmitter battery (lithium battery) from the transmitter (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.



ii.
B232799E02
1.604,0.813 1.75,0.531 false 1.396,0.729 1.573,0.896 0.177,0.167 10 false *1

Install a new or normal battery (lithium battery) (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).

Text in Illustration
*1 Dry Cell Batteries

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.


HINT:

If a new or normal battery is not available, first connect 2 new dry cell batteries (1.5 V) in series. Then connect leads to the batteries and apply 3 V to the transmitter, as shown in the illustration.



iii.

From outside the vehicle, approximately 1 m (3.28 ft.) away from the driver side outside door handle, test the transmitter by pointing its key plate at the vehicle and pressing a transmitter switch.

OK:

The door lock can be operated via the transmitter.

The LED comes on more than once.


·

The operational area differs depending on the user, the way the transmitter is held, and the location.

·

The transmitter's faint electric waves may be affected if the area has strong electric waves or noise. The transmitter's operation area may be shortened or the transmitter may not function.




b.

Inspect the battery capacity.

i.

Remove the battery from the electrical key transmitter that does not operate.


ii.
B232796E04
1.188,1.146 0.594,1.896 true 0.396,1.823 0.563,2 0.167,0.177 10 false *1

Attach a lead wire (0.60 mm [0.027 in.] in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Text in Illustration
*1 Lead Wire

NOTICE:
·

Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.


·

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged




iii.

Carefully pull the lead wire out from the position as shown in the illustration and install the previously removed transmitter battery.


iv.
B260482E02
0.8,0.331 1.233,0.217 false 1.275,0.103 1.447,0.268 0.172,0.164 10 *a

Measure the voltage of the transmitter battery.

Text in Illustration
*a GND

HINT:
·

When measuring the battery voltage, bring the electrical key transmitter within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement. For the entry lock operating range, refer to System Description (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>SYSTEM DESCRIPTION).


·

Perform the measurement when the key is at room temperature.


·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.1 V or less the Data List item "Key Low Battery" displays "Yes".



Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Engine switch off, all doors closed and lock sensor touched 2.2 to 3.2 V