Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297676 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 1.REMOVE FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B171377E26
2.149,3.55 2.297,3.692 0.149,0.142 10 *c 2.672,3.202 2.821,3.344 0.149,0.142 10 *b 0.087,0.096 0.243,0.242 0.156,0.147 10 *a 0.281,2.969 0.377,3.107 0.096,0.139 10 L 1.003,2.969 1.198,3.107 0.195,0.139 10 UL 0.349,3.179 0.542,3.82 false 1.137,3.179 1.33,3.82 false

a.

Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly LH.



b.
B171377E27
2.167,3.566 2.316,3.708 0.149,0.142 10 *c 2.687,3.201 2.836,3.343 0.149,0.142 10 *b 0.087,0.094 0.243,0.241 0.156,0.147 10 *a 1.354,4.463 1.468,4.600 0.114,0.137 10 E 0.225,4.463 0.610,4.600 0.385,0.137 10 LSSR 0.926,4.2 0.708,4.542 false 1.104,4.2 1.322,4.542 false

Check the operation of the door unlock detection switch (w/ Entry and Start System for LHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (E) - 8 (LSSR) Lock 10 kΩ or higher
7 (E) - 8 (LSSR) Unlock Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly LH.



c.
B171377E27
2.167,3.566 2.316,3.708 0.149,0.142 10 *c 2.687,3.201 2.836,3.343 0.149,0.142 10 *b 0.087,0.094 0.243,0.241 0.156,0.147 10 *a 1.354,4.463 1.468,4.600 0.114,0.137 10 E 0.225,4.463 0.610,4.600 0.385,0.137 10 LSSR 0.926,4.2 0.708,4.542 false 1.104,4.2 1.322,4.542 false

Check the operation of the door unlock detection switch (w/ Entry and Start System for RHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (E) - 8 (LSSR) Lock 10 kΩ or higher
7 (E) - 8 (LSSR) Unlock Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly LH.



Hide 2.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B164418E11
0.081,0.058 0.230,0.196 0.149,0.137 10 *a 2.745,3.331 2.895,3.470 0.150,0.139 10 *b 2.23,3.744 2.380,3.884 0.150,0.140 10 *c 0.169,3.025 0.264,3.172 0.095,0.147 10 L 0.592,2.675 0.688,2.823 0.095,0.147 10 L 0.325,2.867 0.525,3.014 0.199,0.147 10 UL 0.781,2.527 0.980,2.674 0.199,0.147 10 UL 0.225,3.221 0.48,3.847 false 0.444,3.068 0.687,3.847 false 0.666,2.867 0.916,3.847 false 0.912,2.723 1.141,3.847 false

a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the front door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Set
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unset


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Unlock
*c Lock

HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock assembly LH.




Hide 3.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B171378E29
0.07,0.063 0.226,0.206 0.156,0.143 10 *a 1.153,3.639 1.302,3.776 0.149,0.137 10 *c 0.61,3.233 0.758,3.370 0.149,0.137 10 *b 3.013,3.073 3.212,3.210 0.199,0.137 10 UL 2.274,3.073 2.369,3.210 0.095,0.137 10 L 2.151,3.827 2.312,3.28 false 2.952,3.827 3.113,3.28 false

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly RH.




b.
B273325E02
0.07,0.055 0.226,0.198 0.156,0.143 10 *a 1.107,3.18 1.256,3.317 0.149,0.137 10 *c 0.577,2.747 0.726,2.885 0.149,0.137 10 *b 2.042,4.052 2.153,4.194 0.111,0.142 10 E 2.716,4.052 3.098,4.194 0.382,0.142 10 LSSR 2.184,4.126 2.339,3.759 false 2.675,4.126 2.52,3.759 false

Check the detection switch (w/ Entry and Start System for LHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly RH.



c.
B273325E03
0.07,0.055 0.226,0.198 0.156,0.143 10 *a 1.107,3.18 1.256,3.317 0.149,0.137 10 *c 0.577,2.747 0.726,2.885 0.149,0.137 10 *b 2.013,4.052 2.123,4.194 0.111,0.142 10 E 2.727,4.052 3.108,4.194 0.382,0.142 10 LSSR 2.184,4.126 2.339,3.759 false 2.675,4.126 2.52,3.759 false

Check the detection switch (w/ Entry and Start System for RHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly RH.



Hide 4.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B164417E10
0.111,0.05 0.260,0.196 0.149,0.147 10 *a 0.417,3.264 0.596,3.424 0.179,0.161 10 *b 0.974,3.774 1.152,3.934 0.178,0.161 10 *c 3.164,3.063 3.362,3.204 0.198,0.141 10 UL 2.947,2.938 3.042,3.079 0.096,0.141 10 L 2.621,2.81 2.840,2.948 0.220,0.139 10 UL 2.432,2.667 2.546,2.808 0.114,0.141 10 L 2.958,3.867 3.279,3.259 false 2.712,3.867 2.981,3.133 false 2.494,3.867 2.723,3.019 false 2.271,3.867 2.468,2.869 false

a.

Check the operation of the door lock motor and double lock motor.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Set
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unset


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock

HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock assembly RH.



b.
B273326E02
0.111,0.071 0.260,0.218 0.149,0.147 10 *a 0.457,2.812 0.636,2.972 0.179,0.161 10 *b 1.043,3.258 1.221,3.419 0.178,0.161 10 *c 2.934,4.047 3.324,4.198 0.390,0.151 10 LSSR 2.201,4.057 2.313,4.197 0.112,0.140 10 E 2.541,3.697 2.345,4.128 false 2.705,3.697 2.9,4.128 false

Check the detection switch (w/ Entry and Start System).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly RH.



c.
B259282E05
0.082,0.074 0.231,0.214 0.149,0.140 10 *a 0.821,2.43 0.970,2.572 0.149,0.142 10 *c 1.208,1.021 1.357,1.163 0.149,0.142 10 *b 0.718,4.337 0.829,4.474 0.111,0.137 10 E 1.051,3.982 0.872,4.41 false

Check the door lock and unlock switch (w/ Key-linked Switch).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 - 8 (E) Lock Below 1 Ω
6 - 8 (E)
5 - 8 (E)
Off 10 kΩ or higher
5 - 8 (E) Unlock Below 1 Ω


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock

If the result is not as specified, replace the front door lock assembly RH.