Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / (desired system) / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Touch Sensor*1 Front door outside handle assembly (for driver side) (unlock sensor) / OFF or ON OFF: Front door outside handle assembly (for driver side) (unlock sensor) not touched
ON: Front door outside handle assembly (for driver side) (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


P-Door Touch Sensor*1 Front door outside handle assembly (for front passenger side) (unlock sensor) / OFF or ON OFF: Front door outside handle assembly (for front passenger side) (unlock sensor) not touched
ON: Front door outside handle assembly (for front passenger side) (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


D-Door Trigger Switch*1 Front door outside handle assembly (for driver side) (lock sensor) / OFF or ON OFF: Front door outside handle assembly (for driver side) (lock sensor) not touched
ON: Front door outside handle assembly (for driver side) (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


P-Door Trigger Switch*1 Front door outside handle assembly (for front passenger side) (lock sensor) / OFF or ON OFF: Front door outside handle assembly (for front passenger side) (lock sensor) not touched
ON: Front door outside handle assembly (for front passenger side) (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Tr/B-Door Unlock SW Back door opener switch assembly (unlock switch) / OFF or ON OFF: Back door opener switch not pushed
ON: Back door opener switch assembly pushed
·

Displays whether the back door opener switch is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door open function does not operate.


Ignition Switch Engine switch on (IG) / OFF or ON OFF: Engine switch off
ON: Engine switch on (IG)
·

Displays whether the IG power source signal input is on or off.

·

Use this Data List item to help determine the cause when all entry and start system/wireless functions do not operate.

·

If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal*2 or clutch pedal*3, the engine switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the S code*4 or L code*5 stored in the certification ECU (smart key ECU assembly) and the code stored in the ID code box*4 or steering lock actuator assembly (steering lock ECU)*5 are compared, and if all codes match, the power source mode is considered on (IG) at that time.


Unmatched Vehicle-ID Key No. (incorrect or correct) / No or Yes No: Communication normal
Yes: Communication malfunction
·

Always "NO" is displayed.

·

No diagnostic function.


No Response Communication response / No or Yes No: Communication normal
Yes: Communication malfunction
The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. Also, if there is electric wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Unmatch Code or Form Code format (incorrect or correct) / No or Yes No: Communication normal
Yes: Communication malfunction
·

Always "NO" is displayed.

·

No diagnostic function.


Key Low Battery Key battery depleted / No or Yes No: Key battery not depleted
Yes: Key battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.6 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Power Save Cnt 10 Min. Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more / 0 to 255 Within range of 0 to 255 If the electrical key transmitter sub-assembly is in the vehicle exterior detection area, communication is frequently performed between the vehicle and the electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the system stops operating. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation.
Power Save Cnt 5 Days Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to engine not being started for 5 days or more / 0 to 255 Within range of 0 to 255 -
Power Save Cnt 14 Days Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger side door disabled) is activated due to engine not being started for 14 days or more / 0 to 255 Within range of 0 to 255 -
ID Code Difference(Resp) ID code (incorrect or correct) / No or Yes No: Communication normal
Yes: Communication malfunction
·

Always "NO" is displayed.

·

No diagnostic function.


C Code Difference Challenge code (incorrect or correct) / No or Yes No: Communication normal
Yes: Communication malfunction
The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is electric wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference (Resp)" and "C Code Difference" in the Data List).
Other potential causes:
·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


ID Code Difference Wireless ID code (incorrect or correct) / No or Yes No: Communication normal
Yes: Communication malfunction
The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference (Resp)" in the Data List.)
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

A communication error due to external noise (RF).

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Different Rolling Code Rolling code (incorrect or correct) / No or Yes No: Communication normal
Yes: Communication malfunction
The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different.
Other potential causes:
·

An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the electric waves cannot reach the vehicle.

·

A communication error due to external noise (RF).

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Auto Entry Cancel SW Entry cancel function setting / OFF or ON Mode status displayed
OFF: Entry and start system not canceled
ON: Entry and start system canceled
The default setting for the entry cancel function is OFF. If the customer requests that the entry and start system functions (locking and unlocking the doors while carrying the key, etc.) be canceled, the setting can be changed through the customize function (See page (Click here)).
Wireless Signal Encryption Support Wireless Signal Encryption Support / Yes or No Yes: Wireless signal encryption support
No: Wireless signal encryption not support
-
Immobiliser Engine immobiliser system status determined by certification ECU (smart key ECU assembly) / Set or Unset Set: Engine immobiliser system set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser system unset (engine start permitted) (engine switch on (ACC) or on (IG))
Problems may be caused by the following:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

Malfunctions in the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly) or engine switch.


Short in Driver Side Door Oscillators Circuit Short in driver side door electrical key antenna circuit / OK or NG OK: Driver side door electrical key antenna circuit is normally
NG: Driver side door electrical key antenna circuit is abnormally
-
Short in Front P Side Door Oscillators Circuit Short in passenger side door electrical key antenna circuit / OK or NG OK: Passenger side door electrical key antenna circuit is normally
NG: Passenger side door electrical key antenna circuit is abnormally
-
Short in D Side Door Oscillators Circuit (Hist) Short in driver side door electrical key antenna circuit (history) / OK or NG (Hist) OK: Driver side door electrical key antenna circuit was normally
NG (Hist): Driver side door electrical key antenna circuit was abnormally
-
Short in Fr P Side Door Oscillators Circuit (Hist) Short in passenger side door electrical key antenna circuit (history) / OK or NG (Hist) OK: Passenger side door electrical key antenna circuit was normally
NG (Hist): Passenger side door electrical key antenna circuit was abnormally
-
Door Unlock Mode2 Door Unlock Mode2 / All or Driver Customization status displayed -
Ignition Available Area Ignition available area / Front or All Customization status displayed -
Parking Wait Time Parking wait time / 0.5s, 1.5s, 2.5s, 5s Customization status displayed -
Trunk Open Mode Luggage compartment door open mode / ON or OFF Customization status displayed -
Key Low Battery Warning Low key battery warning / OFF or ON Customization status displayed -
Touch Activation Over Threshold Consecutive entry lock operation / Active or Not Active Customization status displayed -
Key Left in Vehicle Buz Key left in vehicle buzzer / OFF or ON Customization status displayed -
Engine Start Indicator Engine start indicator / OFF or ON Customization status displayed -

*1: Data from an actual vehicle provided for reference.

*2: for Automatic Transmission

*3: for Manual Transmission

*4: w/ ID Code Box

*5: w/o ID Code Box


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch signal / OFF or ON OFF: Driver side door closed
ON: Driver side door opened
-
D-Door Lock Pos SW Driver side door unlock detection switch signal / LOCK or UNLOCK LOCK: Driver side door locked
UNLOCK: Driver side door unlocked
-
P Door Courtesy SW Passenger side door courtesy light switch signal / OFF or ON OFF: Passenger side door closed
ON: Passenger side door opened
-
P-Door Lock Pos SW Passenger side door unlock detection switch signal / LOCK or UNLOCK LOCK: Passenger side door locked
UNLOCK: Passenger side door unlocked
-
Luggage Courtesy SW Luggage compartment door courtesy light switch signal / OFF or ON OFF: Luggage compartment door closed
ON: Luggage compartment door open
-
IG SW Engine switch on (IG) / OFF or ON ON: Engine switch on (IG)
OFF: Engine switch off
-
ACC SW Engine switch on (ACC) / OFF or ON OFF: Engine switch off
ON: Engine switch on (ACC)
-
Battery Power Supply Control Voltage Battery power supply control voltage / 0 to 21.4 V 11 to 14 V -
Battery Power Supply Back Up Voltage Battery power supply backup voltage / 0 to 21.4 V 11 to 14 V -
IG Power Supply Voltage IG power supply voltage / 0 to 21.4 V 11 to 14 V -
ACC Voltage ACC voltage / 0 to 21.4 V 11 to 14 V -

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS-VSC-TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Almost the same as actual vehicle speed -



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / (desired system) / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Entry & Start
Tester Display Test Part Control Range Diagnostic Note
Overhead Tuner Power Supply ON Door control receiver OFF/ON -
Power for D-Seat Sens Front door outside handle assembly (for driver side) OFF/ON -
Power for P-Seat Sens Front door outside handle assembly (for passenger side) OFF/ON -
Power/Engine SW Light Engine switch light OFF/ON When performing this Active Test, make sure the following condition is met:

The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.



Main Body
Tester Display Test Part Control Range Diagnostic Note
Door Lock Door lock motor Unlock / Lock -
D-Door Unlock Driver side door lock motor OFF / ON -
Trunk and Back-Door Open Operate luggage door closer assembly motor OFF / ON -
Wireless Buzzer Wireless door lock buzzer OFF / ON -
Hazard Turn signal flasher assembly OFF / ON -