Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2014.05
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Key Luggage Compartment Lock-in Prevention Function does not Operate  


DESCRIPTION

If the entry luggage compartment lock-in prevention function does not operate, there may be a problem with the communication between the No. 3 indoor electrical key oscillator (inside luggage) and electrical key transmitter sub-assembly, wave interference or a malfunction in the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B264533E70
3.583,0.865 3.667,1.01 0.083,0.146 10 false 3 3.094,0.885 3.49,1.042 0.396,0.156 10 false CLGB 5.146,0.885 5.229,1.031 0.083,0.146 10 false 8 5.313,0.969 5.708,1.115 0.396,0.146 10 false CG7B 3.573,1.396 3.656,1.542 0.083,0.146 10 false 1 3.01,1.417 3.49,1.573 0.479,0.156 10 false ANTE7 5.146,1.427 5.229,1.573 0.083,0.146 10 false 9 5.313,1.51 5.719,1.656 0.406,0.146 10 false CLG7 4.667,1.938 4.958,2.104 0.292,0.167 10 false D40 4.667,2.094 6.219,2.469 1.552,0.375 10 false Certification ECU (Smart Key ECU Assembly) 1.177,1.948 1.417,2.104 0.24,0.156 10 false H9 1.188,2.104 3.479,2.469 2.292,0.365 10 false No. 3 Indoor Electrical Key Oscillator (Inside Luggage)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK ENTRY FUNCTION (ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION)
a.

Check that the entry luggage compartment open function operates (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

Result:
Result Proceed to
Entry luggage compartment door open function operates A
Entry luggage compartment door open function does not operate B




A

2.CHECK WAVE ENVIRONMENT

B

2.CHECK WAVE ENVIRONMENT
a.
B311617E01
1.161,1.454 2.097,0.272 2.097,0.272 1.522,1.263 false 2.365,0.173 2.550,0.347 0.185,0.173 10 *a 2.092,0.274 2.347,0.274 false

Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key oscillator (inside luggage), and check that the entry luggage compartment lock-in prevention function operates.

Text in Illustration
*a Inspection Point

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key oscillator (inside luggage), communication is not possible.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the No. 3 indoor electrical key oscillator (inside luggage), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Entry functions operate normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK KEY DIAGNOSTIC MODE
3.CHECK KEY DIAGNOSTIC MODE
a.

B311617E01
1.161,1.454 2.097,0.272 2.097,0.272 1.522,1.263 false 2.365,0.173 2.550,0.347 0.185,0.173 10 *a 2.092,0.274 2.347,0.274 false

Text in Illustration
*a Inspection Point

b.

When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

HINT:
·

Place the key in the luggage area.

·

If the buzzer sounds, it can be determined that the No. 3 indoor electrical key oscillator (inside luggage compartment) is operating normally.



OK:

Wireless door lock buzzer sounds.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the D40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H9 No. 3 indoor electrical key oscillator (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-9 (CLG7) - H9-1 (ANTE7) Always Below 1 Ω
D40-8 (CG7B) - H9-3 (CLGB) Always Below 1 Ω
D40-9 (CLG7) - Body ground Always 10 kΩ or higher
D40-8 (CG7B) - Body ground Always 10 kΩ or higher




OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the D40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H9 No. 3 indoor electrical key oscillator (inside luggage) connector.


c.
U190220E01
1.89,2.092 2.295,2.253 0.405,0.161 10 CLGB 1.074,2.092 1.568,2.253 0.494,0.161 10 ANTE7 0.168,0.103 0.354,0.264 0.186,0.161 10 *a 1.948,1.682 2.067,2.069 false 1.504,1.682 1.386,2.069 false 0.577,1.024 0.795,1.180 0.218,0.156 10 H9 1.717,4.186 1.903,4.347 0.186,0.161 10 *c 2.634,4.192 2.820,4.353 0.186,0.161 10 *d 0.145,3.283 0.550,3.444 0.405,0.161 10 GND 0.461,2.255 0.646,2.416 0.186,0.161 10 *b

Measure the voltage according to the value(s) in the table below.


OK:
Tester Connection Switch Condition Tool Setting Specified Condition
H9-1 (ANTE7) - H9-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)


Text in Illustration
*a Front view of wire harness connector
(to No. 3 Indoor Electrical Key Oscillator (inside luggage compartment))
*b Waveform
*c Driver side door lock sensor not touched
*d Driver side door lock sensor touched


OK

6.REPLACE NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.REPLACE NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)
a.

Replace the No. 3 indoor electrical key oscillator (inside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL).



NEXT

7.CHECK NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)
7.CHECK NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)
a.

Check that the entry luggage compartment lock-in prevention function operates normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry luggage compartment lock-in prevention function operates normally.




OK

END (NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)