When the wireless functions can be used to lock and unlock the doors, the communication between the door control receiver and certification ECU (smart key ECU assembly) is normal. When the entry functions do not operate, one of the following may be the cause: 1) entry cancel function is set through customization; 2) malfunction in the entry and start system communication (electrical key transmitter sub-assembly and vehicle); or 3) electrical interference.
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
According to the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| Entry function cancel is OFF | A |
| Entry function cancel is ON | B |
A
B
Move the electrical key transmitter sub-assembly as described below and perform the operation inspection (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
The transmitting waves of the wireless functions and entry functions are the same, but the wave logic is different. Therefore, it is possible that only the wireless functions or only the entry functions are affected by wave interference.
Bring the electrical key transmitter sub-assembly near the driver door outside handle assembly, and perform a front driver door entry lock and unlock operation check.
If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.98 ft.) |
Bring the electrical key transmitter sub-assembly near the front passenger side door outside handle assembly, and perform a front passenger side door entry lock and unlock operation check.
If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.98 ft.) |
Bring the electrical key transmitter sub-assembly near the electrical key antenna (outside luggage), and perform an entry luggage compartment door open function check.
If the key is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.
| *a | Approximately 0.3 m (0.98 ft.) |
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
If wave interference seems to be the likely cause of the problem, ask the customer if the problem occurs in specific locations.
Move the vehicle to a different location, perform the following procedure and check if the symptoms can be reproduced.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| All operation checks fail | A |
| All checks are normal | B |
| Some operation checks are normal | C |
A
B
C
Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check the electrical key antenna (for driver door):
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
Check the electrical key antenna (for front passenger door):
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.
Check the indoor electrical key oscillator (front floor):
| *a | Inspection point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 2 indoor electrical key oscillator (rear floor):
| *a | Inspection point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the electrical key antenna (outside luggage):
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| All diagnostic mode inspections fail | A |
| Some diagnostic mode inspections fail (door) | B |
| Some diagnostic mode inspections fail (interior) | C |
| Some diagnostic mode inspections fail (outside) | D |
| All diagnostic mode inspections are normal | E |
A
B
C
D
E
Check if there is another key available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered key sub-assembly is not available | A |
| Another registered key sub-assembly is available | B |
A
B
Register the electrical key transmitter sub-assembly (Refer to the Service Bulletin).
NEXT
Check that the entry function operates normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Entry function operates normally.
OK
NG