Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A6  Open in Rear Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key oscillator (rear floor). For the No. 2 indoor electrical key oscillator (rear floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A6 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key oscillator (rear floor) (between terminals CLG6 and ANTE6, or terminals CG6B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A6 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key oscillator (rear floor) (CLG6 - ANTE6, CG6B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 2 indoor electrical key oscillator (rear floor)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in rear seat area:
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A6 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B286267E91
1.177,1.031 1.646,1.198 0.469,0.167 10 false ANTE6 1.25,1.458 1.656,1.625 0.406,0.167 10 false CLGB 1.75,0.865 1.875,1.052 0.125,0.188 10 false 1 1.74,1.292 1.865,1.479 0.125,0.188 10 false 3 0.375,2.385 0.656,2.563 0.281,0.177 10 false H15 0.354,2.563 2.031,2.927 1.677,0.365 10 false No. 2 Indoor Electrical Key Oscillator (Rear Floor) 5.521,1 5.906,1.167 0.385,0.167 10 false CLG6 5.542,1.438 5.927,1.604 0.385,0.167 10 false CG6B 5.542,1.875 5.865,2.052 0.323,0.177 10 false GND 5.229,0.802 5.438,0.969 0.208,0.167 10 false 11 5.24,1.25 5.448,1.417 0.208,0.167 10 false 10 5.25,1.677 5.458,1.844 0.208,0.167 10 false 11 5.208,1.01 5.49,1.167 0.281,0.156 10 false D40 5.208,1.448 5.49,1.604 0.281,0.156 10 false D40 5.208,1.875 5.49,2.031 0.281,0.156 10 false D48 5.229,2.438 6.781,2.792 1.552,0.354 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 2 indoor electrical key oscillator (rear floor) has an antenna coil between CLG4 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key oscillator (rear floor).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the D40 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the H15 No. 2 indoor electrical key oscillator (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-11 (CLG6) - H15-1 (ANTE6) Always Below 1 Ω
D40-10 (CG6B) - H15-3 (CLGB) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D40-11 (CLG6) - Body ground Always 10 kΩ or higher
D40-10 (CG6B) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)
U190206E02
3.625,1.396 3.99,2.156 false 3.438,1.417 3.104,2.156 false 2.698,1.51 2.427,2.156 false 1.208,2.771 1.417,2.969 0.208,0.198 10 false *b 0.177,0.042 0.385,0.24 0.208,0.198 10 false *a 1.573,4.365 1.75,4.542 0.177,0.177 10 false *c 2.917,2.188 3.333,2.385 0.417,0.198 10 false CLG6 2.333,4.365 2.51,4.552 0.177,0.188 10 false *d 3.802,2.188 4.219,2.385 0.417,0.198 10 false CG6B 0.99,3.646 1.333,3.813 0.344,0.167 10 false GND 2.229,2.177 2.583,2.354 0.354,0.177 10 false GND 3.417,0.563 3.708,0.719 0.292,0.156 10 false D40 2.188,0.563 2.448,0.729 0.26,0.167 10 false D48

Text in Illustration
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Waveform
*c Within approximately 30 seconds from when the door is closed *d After approximately 30 seconds from when the door is closed

a.

Reconnect the D40 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the H15 No. 2 indoor electrical key oscillator (rear floor) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
D40-11 (CLG6) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
D40-10 (CG6B) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key oscillator (rear floor) with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL).



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)