Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key oscillator (inside luggage). For the certification ECU (smart key ECU assembly) to detect when the key is inside the luggage compartment, the signal from the certification ECU (smart key ECU assembly) requesting a response from the key is transmitted inside the luggage compartment. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key oscillator (inside luggage) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A7 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key oscillator (inside luggage) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*1).
·

Wire harness or connector

·

No. 3 indoor electrical key oscillator (inside luggage)

·

Certification ECU (smart key ECU assembly)


Any time*2

*1: Only output while a malfunction is present.

*2: Only when the vehicle is stopped.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When key is in luggage compartment:
·

Power source mode does not change when engine switch is pressed

·

Key becomes locked inside vehicle


-

Related Data List and Active Test
DTC No. Data List and Active Test
B27A7 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B286267E92
1.229,1.01 1.688,1.188 0.458,0.177 10 false ANTE7 1.729,0.885 1.865,1.073 0.135,0.188 10 false 1 1.74,1.313 1.865,1.5 0.125,0.188 10 false 3 5.531,1 5.927,1.177 0.396,0.177 10 false CLG7 5.521,1.438 5.948,1.604 0.427,0.167 10 false CG7B 5.542,1.885 5.896,2.052 0.354,0.167 10 false GND 5.24,1.698 5.438,1.844 0.198,0.146 10 false 11 5.271,1.25 5.417,1.427 0.146,0.177 10 false 8 5.208,1.01 5.49,1.167 0.281,0.156 10 false D40 5.26,0.813 5.385,1 0.125,0.188 10 false 9 1.302,1.438 1.698,1.604 0.396,0.167 10 false CLGB 0.438,2.417 0.635,2.604 0.198,0.188 10 false H9 0.438,2.594 2.094,2.958 1.656,0.365 10 false No. 3 Indoor Electrical Key Oscillator (Inside Luggage) 5.188,2.417 6.75,2.771 1.563,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.208,1.448 5.49,1.604 0.281,0.156 10 false D40 5.208,1.885 5.49,2.042 0.281,0.156 10 false D48

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses a LIN communication system and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".

·

No. 3 indoor electrical key oscillator (inside luggage) has an antenna coil between CLG6 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the No. 3 indoor electrical key oscillator (inside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the D40 and D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H9 No. 3 indoor electrical key oscillator (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-9 (CLG7) - H9-1 (ANTE7) Always Below 1 Ω
D40-8 (CG7B) - H9-3 (CLGB) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D40-9 (CLG7) - Body ground Always 10 kΩ or higher
D40-8 (CG7B) - Body ground Always 10 kΩ or higher




OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)
U190205E02
3.688,1.396 3.438,2.083 true 2.708,1.51 2.531,2.073 true 3.781,1.396 4.104,2.083 true 0.198,0.115 0.417,0.313 0.219,0.198 10 false *a 1.208,2.792 1.427,2.99 0.219,0.198 10 false *b 0.969,3.635 1.313,3.802 0.344,0.167 10 false GND 1.563,4.333 1.781,4.531 0.219,0.198 10 false *c 2.385,4.333 2.604,4.531 0.219,0.198 10 false *d 3.25,2.104 3.646,2.271 0.396,0.167 10 false CLG7 3.948,2.104 4.344,2.271 0.396,0.167 10 false CG7B 2.188,0.646 2.458,0.802 0.271,0.156 10 false D48 3.417,0.646 3.698,0.813 0.281,0.167 10 false D40 2.365,2.083 2.781,2.26 0.417,0.177 10 false GND

Text in Illustration
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Waveform
*c Within approximately 30 seconds from when the door is closed *d After approximately 30 seconds from when the door is closed

a.

Reconnect the D40 and D48 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the H9 No. 3 indoor electrical key oscillator (inside luggage) connector.


c.

Using an oscilloscope, check the waveform.

HINT:

Check that the customizing "Ignition Available Area" setting of entry and start system is All (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).


OK:
Tester Connection Switch Condition Tool Setting Specified Condition
D40-9 (CLG7) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Door is open

3.

Door is closed

4.

30 seconds elapse

5.

Electrical key transmitter not inside vehicle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)
D40-8 (CG7B) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Door is open

3.

Door is closed

4.

30 seconds elapse

5.

Electrical key transmitter not inside vehicle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)




OK

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)
a.

Temporarily replace the No. 3 indoor electrical key oscillator (inside luggage) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

OK

END (NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)