Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the certification ECU (smart key ECU assembly) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the luggage compartment door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and ANT1, or terminals CG8B and ANT2).

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A8 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - ANT1, CG8B - ANT2) (1 trip detection logic*1).
·

Wire harness or connector

·

Electrical key antenna (outside luggage)

·

Certification ECU (smart key ECU assembly)


Any time*2

*1: Only output while a malfunction is present.

*2: Only when the vehicle is stopped.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for luggage compartment door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B286267E93
1.313,1.01 1.677,1.177 0.365,0.167 10 false ANT1 1.74,0.875 1.865,1.042 0.125,0.167 10 false 1 1.75,1.323 1.885,1.5 0.135,0.177 10 false 2 5.531,1 5.917,1.177 0.385,0.177 10 false CLG8 5.531,1.438 5.948,1.604 0.417,0.167 10 false CG8B 5.542,1.885 5.875,2.042 0.333,0.156 10 false GND 5.219,1.875 5.479,2.042 0.26,0.167 10 false D48 5.24,1.698 5.438,1.854 0.198,0.156 10 false 11 5.219,1.448 5.5,1.615 0.281,0.167 10 false D40 5.26,1.25 5.396,1.417 0.135,0.167 10 false 1 5.208,1.01 5.521,1.177 0.313,0.167 10 false D40 5.281,0.813 5.406,0.99 0.125,0.177 10 false 2 1.302,1.438 1.677,1.615 0.375,0.177 10 false ANT2 0.438,2.417 0.656,2.583 0.219,0.167 10 false H3 0.438,2.604 1.865,2.969 1.427,0.365 10 false Electrical Key Antenna (Outside Luggage) 5.188,2.417 6.698,2.781 1.51,0.365 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses a LIN communication system and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".

·

Electrical key antenna (outside luggage) has an antenna coil between CLG8 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the electrical key antenna (outside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE))
a.

Disconnect the D40 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the H3 electrical key antenna (outside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-2 (CLG8) - H3-1 (ANT1) Always Below 1 Ω
D40-1 (CG8B) - H3-2 (ANT2) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D40-2 (CLG8) - Body ground Always 10 kΩ or higher
D40-1 (CG8B) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

b.
B226391E30
2.298,0.98 2.722,1.155 0.424,0.174 10 ANT2 0.685,0.979 1.100,1.153 0.415,0.174 10 ANT1 0.154,0.043 0.545,0.217 0.391,0.174 10 *a 2.271,1.064 1.841,1.064 false 1.584,1.064 1.153,1.064 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ANT1) - 2 (ANT2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Electrical Key Antenna (Outside Luggage))



OK

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new or normally functioning one.



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG