Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 drive circuit, IG2 drive circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2271 Either condition is met (1-trip detection logic*1):
·

The IG1 or IG2 drive circuit in the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.


·

AM2 No. 2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Turn the engine switch on (IG).
HINT:

To turn the engine switch on (IG), carry the key and press the engine switch twice with the shift lever in P or N*2 and the brake pedal*2 or clutch pedal*3 released.



*1: Only output while a malfunction is present and the engine switch is on (IG)

*2: for Automatic Transmission

*3: for Manual Transmission


HINT:
·

The IG1 and IG2 drive circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 drive circuits turn on, even if the certification ECU (smart key ECU assembly) operates incorrectly, the IG hold circuit maintains the engine switch on (IG) state.



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power source mode is not allowed to change to on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2271
Power Source Control
·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

Latch Circuit


Engine
·

Ignition Status


-

WIRING DIAGRAM

B312725E03
3.49,1.042 3.594,1.188 0.104,0.146 10 false 6 2.583,4.083 2.906,4.24 0.323,0.156 10 false GND 3.021,1.229 3.344,1.375 0.323,0.146 10 false IG1D 3.417,1.229 3.708,1.406 0.292,0.177 10 false D41 3.99,1.042 4.156,1.188 0.167,0.146 10 false 15 3.99,1.229 4.229,1.385 0.24,0.156 10 false 3A 4.021,0.635 4.146,0.833 0.125,0.198 10 false 1 3.979,0.823 4.229,0.969 0.25,0.146 10 false 3E 5.813,0.99 6.385,1.156 0.573,0.167 10 false ECU IG1 6.458,4.094 6.635,4.24 0.177,0.146 10 false 12 6.458,4.281 6.667,4.448 0.208,0.167 10 false 3A 6.51,3.688 6.625,3.854 0.115,0.167 10 false 3 6.448,3.854 6.656,4.021 0.208,0.167 10 false 3A 6.469,2.688 6.635,2.833 0.167,0.146 10 false 32 6.448,2.885 6.677,3.042 0.229,0.156 10 false 3A 6.458,1.656 6.667,1.813 0.208,0.156 10 false 34 6.448,1.844 6.708,1.99 0.26,0.146 10 false 3C 6.458,0.635 6.646,0.813 0.188,0.177 10 false 35 6.448,0.833 6.708,1.01 0.26,0.177 10 false 3C 4.875,4.5 5.469,4.667 0.594,0.167 10 false IG1 NO.4 4.885,3.51 5.479,3.688 0.594,0.177 10 false IG1 NO.3 4.833,2.479 5.479,2.646 0.646,0.167 10 false IG1 NO. 2 4.823,1.448 5.479,1.604 0.656,0.156 10 false IG1 NO. 1 5.896,1.99 6.198,2.156 0.302,0.167 10 false DRL 5.833,4 6.385,4.333 0.552,0.333 10 false SEAT HTR RH 5.781,3.021 6.385,3.177 0.604,0.156 10 false HEATER 2.271,3.917 2.448,4.063 0.177,0.146 10 false 11 2.229,4.104 2.542,4.25 0.313,0.146 10 false D48 2.313,2.594 2.417,2.74 0.104,0.146 10 false 9 2.323,1.031 2.427,1.177 0.104,0.146 10 false 2 2.24,2.781 2.521,2.938 0.281,0.156 10 false D48 2.24,1.219 2.521,1.375 0.281,0.156 10 false D48 2.573,1.229 2.781,1.396 0.208,0.167 10 false +B 1.365,1.354 2.083,1.521 0.719,0.167 10 false AM2 NO. 2 0.156,1.24 1.25,1.406 1.094,0.167 10 false from MAIN Fuse 3.99,4.875 6.635,5.063 2.646,0.188 10 false Instrument Panel Junction Block Assembly 2.167,4.885 3.698,5.25 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 2.594,2.792 2.917,2.938 0.323,0.146 10 false IG2D 1.115,3.01 1.365,3.156 0.25,0.146 10 false IG2 0.823,2.667 0.917,2.823 0.094,0.156 10 false 3 1.583,2.292 1.688,2.438 0.104,0.146 10 false 5 0.813,2.271 0.906,2.427 0.094,0.156 10 false 1 1.583,2.708 1.688,2.854 0.104,0.146 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
U190193E01
0.091,0.052 0.277,0.213 0.186,0.161 10 *a 0.334,1.362 0.630,1.518 0.295,0.156 10 D48 1.312,1.357 1.1,1.9 false 0.948,1.916 1.146,2.062 0.198,0.146 10 +B

a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D48-2 (+B) - Body ground Always 9.5 to 16 V


Text in Illustration
*a Rear view of harness connected
(to Certification ECU (Smart Key ECU Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
U190194E01
0.091,0.042 0.277,0.203 0.186,0.161 10 *a 0.334,1.352 0.630,1.508 0.295,0.156 10 D48 2.009,1.92 2.349,2.073 0.340,0.154 10 GND 2.049,1.584 2.175,1.913 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D48-11 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of harness connected
(to Certification ECU (Smart Key ECU Assembly))



OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the D48 certification ECU (smart key ECU assembly) connector.


U190187E01
0.18,0.129 0.366,0.290 0.186,0.161 10 *a 4.805,0.934 5.100,1.090 0.295,0.156 10 D41 2.187,0.932 2.482,1.088 0.295,0.156 10 D48 4.388,1.629 4.13,2.287 false 1.978,1.736 1.762,2.287 false 3.927,2.312 4.290,2.468 0.363,0.156 10 IG1D 1.531,2.313 1.893,2.469 0.363,0.156 10 IG2D

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
D41-6 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) Below 1 V → 9 V or higher
D48-9 (IG2D) - Body ground Engine switch on (ACC) → Engine switch on (IG) Below 1 V → 9 V or higher



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)