Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  U0073  Control Module Communication Bus Off  U0100  Lost Communication with ECM / PCM "A"  U0101  Lost Communication with TCM  U0122  Lost Communication with Vehicle Dynamics Control Module  U0140  Lost Communication with Body Control Module  U0155  Lost Communication with Instrument Panel Cluster Control Module (Combination Meter)  U0401  Invalid Data Received from ECM/PCM "A"  U0422  Invalid Data Received from Body Control Module  


DESCRIPTION

These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly) and the ECM, TCM, main body ECU (network gateway ECU), combination meter assembly or brake actuator assembly (skid control ECU).

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
U0073 CAN communication system malfunction (1-trip detection logic*). CAN communication system Turn the engine switch on (IG) and wait 10 seconds or more.
U0100 CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*). ECM Turn the engine switch on (IG) and wait 10 seconds or more.
U0101 CAN communication malfunction between the certification ECU (smart key ECU assembly) and TCM (1-trip detection logic*). TCM Turn the engine switch on (IG) and wait 10 seconds or more.
U0122 CAN communication malfunction between the certification ECU (smart key ECU assembly) and brake actuator assembly (skid control ECU) (1-trip detection logic*). Brake actuator assembly (skid control ECU) Turn the engine switch on (IG) and wait 10 seconds or more.
U0140 CAN communication malfunction between the certification ECU (smart key ECU assembly) and main body ECU (network gateway ECU) (1-trip detection logic*). Main body ECU (network gateway ECU) Turn the engine switch on (IG) and wait 10 seconds or more.
U0155 CAN communication malfunction between the certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*). Combination meter assembly Turn the engine switch on (IG) and wait 10 seconds or more.
U0401 CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*). ECM Turn the engine switch on (IG) and wait 10 seconds or more.
U0422 CAN communication malfunction between the certification ECU (smart key ECU assembly) and main body ECU (network gateway ECU) (1-trip detection logic*). Main body ECU (network gateway ECU) Turn the engine switch on (IG) and wait 10 seconds or more.

*: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
U0073 There is no effect on vehicle behavior. -
U0100 There is no effect on vehicle behavior.
If the following conditions are met, it is determined that the malfunction is not in the direct line (TACH) but in CAN communication.
·

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

·

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (TACH).
·

When the engine switch is pressed, the engine stops cranking after 6 seconds.

·

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.


U0101 There is no effect on vehicle behavior. -
U0122 There is no effect on vehicle behavior. -
U0140 Doors cannot be locked or unlocked.
The warning (wireless buzzer) does not sound.
-
U0155 The warning (meter buzzer) does not sound and the meter does not indicate a warning. -
U0401 There is no effect on vehicle behavior. -
U0422 Doors cannot be locked or unlocked.
The warning (wireless buzzer) does not sound.
-

Related Data List and Active Test Items
DTC Data List Item Active Test Item
U0073
U0100
U0101
U0122
U0140
U0155
U0401
U0422
- -

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK FOR DTC

NEXT

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)