Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297682 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The transponder key amplifier coil built into the engine switch is open or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*1):
·

Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the engine switch).

·

The transponder key amplifier coil built into the engine switch is open.


·

Engine switch

·

Harness or connector

·

Certification ECU (smart key ECU assembly)


With the shift lever in P*2, the electrical key transmitter sub-assembly is held against the engine switch and an engine start operation is performed by pressing and holding the engine switch when the transmitter battery is depleted.

*1: Only output while a malfunction is present.

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding electrical key transmitter sub-assembly against engine switch and pressing and holding engine switch with shift lever in P* -

*: for Automatic Transmission


Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

B271004E30
1.958,2.198 2.104,2.365 0.146,0.167 10 false 6 0.854,2.979 1.813,3.177 0.958,0.198 10 false Engine Switch 0.865,2.802 1.25,2.969 0.385,0.167 10 false D25 1.573,0.76 1.875,0.927 0.302,0.167 10 false VC5 1.458,2.313 1.885,2.479 0.427,0.167 10 false AGND 1.938,0.646 2.135,0.823 0.198,0.177 10 false 10 1.958,1.156 2.083,1.333 0.125,0.177 10 false 7 5.052,2.99 6.615,3.354 1.563,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.052,2.823 5.458,2.99 0.406,0.167 10 false D41 1.448,1.781 1.875,1.948 0.427,0.167 10 false CODE 1.49,1.281 1.875,1.458 0.385,0.177 10 false TXCT 1.958,1.677 2.104,1.833 0.146,0.156 10 false 8 5.083,0.656 5.219,0.802 0.135,0.146 10 false 1 5.063,2.198 5.24,2.365 0.177,0.167 10 false 24 5.083,1.167 5.229,1.323 0.146,0.156 10 false 9 5.094,1.677 5.229,1.844 0.135,0.167 10 false 7 5.292,0.729 5.604,0.906 0.313,0.177 10 false VC5 5.313,2.292 5.75,2.469 0.438,0.177 10 false AGND 5.292,1.76 5.74,1.938 0.448,0.177 10 false CODE 5.292,1.25 5.74,1.406 0.448,0.156 10 false TXCT

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D25 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D41-1 (VC5) - D25-10 (VC5) Always Below 1 Ω
D41-7 (CODE) - D25-8 (CODE) Always Below 1 Ω
D41-9 (TXCT) - D25-7 (TXCT) Always Below 1 Ω
D41-24 (AGND) - D25-6 (AGND) Always Below 1 Ω
D41-1 (VC5) - Body ground Always 10 kΩ or higher
D41-7 (CODE) - Body ground Always 10 kΩ or higher
D41-9 (TXCT) - Body ground Always 10 kΩ or higher
D41-24 (AGND) - Body ground Always 10 kΩ or higher




OK

2.REPLACE ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE ENGINE SWITCH
a.

Temporarily replace the engine switch with a new or normally functioning one (See page Engine / Hybrid System>FA20 STARTING>ENGINE SWITCH>REMOVAL).



NEXT

3.CLEAR DTC
4.CHECK FOR DTC

OK

END (ENGINE SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)