Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297682 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B278A A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*1).
·

Harness or connector


·

Engine switch


·

Certification ECU (smart key ECU assembly)


With the shift lever in P*2, the electrical key transmitter sub-assembly is held against the engine switch and an engine start operation is performed by pressing and holding the engine switch when the transmitter battery is depleted.

*1: Only output while a malfunction is present.

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding electrical key transmitter sub-assembly against engine switch and pressing and holding engine switch with shift lever in P* -

*: for Automatic Transmission


Related Data List and Active Test
DTC Code Data List and Active Test
B278A -

WIRING DIAGRAM

B271005E43
0.927,2.99 1.844,3.167 0.917,0.177 10 false Engine Switch 0.927,2.823 1.24,2.99 0.313,0.167 10 false D25 1.552,1.177 1.865,1.344 0.313,0.167 10 false VC5 1.438,2.094 1.885,2.26 0.448,0.167 10 false AGND 1.938,1.042 2.188,1.229 0.25,0.188 10 false 10 1.948,1.958 2.125,2.135 0.177,0.177 10 false 6 5.063,1.052 5.219,1.219 0.156,0.167 10 false 1 5.031,1.979 5.229,2.135 0.198,0.156 10 false 24 5.333,2.083 5.771,2.26 0.438,0.177 10 false AGND 5.052,3.01 6.615,3.375 1.563,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.052,2.823 5.354,2.99 0.302,0.167 10 false D41 5.302,1.156 5.604,1.333 0.302,0.177 10 false VC5

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D25 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
D41-1 (VC5) - D25-10 (VC5) Always Below 1 Ω
D41-24 (AGND) - D25-6 (AGND) Always Below 1 Ω
D41-1 (VC5) - Body ground Always 10 kΩ or higher
D41-24 (AGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the D25 engine switch connector.


c.
U190201E02
0.469,1.646 1.177,1.646 true 1.844,1.635 2.552,1.635 true 0.125,0.021 0.302,0.208 0.177,0.188 10 false *a 2.958,3.302 3.281,3.479 0.323,0.177 10 false GND 0.115,1.583 0.448,1.74 0.333,0.156 10 false VC5 2.635,1.552 3.063,1.708 0.427,0.156 10 false AGND 1.385,0.302 1.677,0.458 0.292,0.156 10 false D25

Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition
Item Content
Tester Connection D25-10 (VC5) - D25-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not inside vehicle, and within 30 seconds after engine switch pushed

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Component with harness connected
(Engine Switch)



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)