Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297684 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY AMPLIFIER


U146860E03
3.417,0.25 3.708,0.406 0.292,0.156 10 false D54

a.

Disconnect the D54 transponder key amplifier connector.


b.

Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
D54-7 (AGND) - Body ground - GR - Body ground Ground Always Below 1 Ω


c.

Reconnect the D54 transponder key amplifier connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
D54-1 (VC5) - D54-7 (AGND) Input R - GR Transponder key amplifier power supply Ignition switch ON 4.5 to 5.5 V
D54-4 (CODE) - D54-7 (AGND) Output LG - GR Demodulated signal of key code data Key inserted in ignition key cylinder Pulse generation
D54-5 (TXCT) - D54-7 (AGND) Output W-G - GR Key code output signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)


U146875E04
1.667,6.75 1.854,6.906 0.188,0.156 10 false *2 0.323,0.177 0.51,0.333 0.188,0.156 10 false *1 3.438,3.188 3.667,3.344 0.229,0.156 10 false MB 3.74,0.969 3.979,1.125 0.24,0.156 10 false MB 0.896,1.823 1.104,1.979 0.208,0.156 10 false 3C 0.885,1.167 1.073,1.333 0.188,0.167 10 false 3D 1.063,2.396 1.26,2.563 0.198,0.167 10 false 3E 5.854,1.833 6.052,2.01 0.198,0.177 10 false 3A 5.865,1.156 6.083,1.313 0.219,0.156 10 false 3B 6.25,4.052 6.479,4.208 0.229,0.156 10 false 3E 4.188,4.073 4.417,4.229 0.229,0.156 10 false 3C 1.427,4.073 1.656,4.229 0.229,0.156 10 false 3D 4.917,5.313 5.146,5.469 0.229,0.156 10 false 3A 1.833,5.323 2.063,5.479 0.229,0.156 10 false 3B 4.229,6.906 4.448,7.063 0.219,0.156 10 false D6 3.063,6.906 3.344,7.063 0.281,0.156 10 false A73 3.698,6.906 3.917,7.063 0.219,0.156 10 false D5 5.896,7.51 6.125,7.667 0.229,0.156 10 false D6 3.594,7.51 3.823,7.667 0.229,0.156 10 false D5 1.125,7.521 1.406,7.677 0.281,0.156 10 false A73

Text in Illustration
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Network Gateway ECU)

a.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


b.

Disconnect the D5, D6 and A73 main body ECU (network gateway ECU) connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
MB-1 (BECU) - Body ground Input None - Body ground Battery power supply Always 11 to 14 V
MB-8 (IG) - Body ground Input None - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
MB-9 (ACC) - Body ground Input None - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-11 (GND) - Body ground - None - Body ground Ground Always Below 1 Ω
MB-32 (BMPX) - Body ground Input None - Body ground Battery power supply Always 11 to 14 V
D5-22 (KSW) - Body ground Input BR - Body ground Unlock warning switch input No key in ignition key cylinder (off) Below 1 V
Key inserted ignition key cylinder (on) 11 to 14 V
D6-1 (GND) - Body ground - B - Body ground Ground Always Below 1 Ω
A73-4 (GND) - Body ground - B-Y - Body ground Ground Always Below 1 Ω


d.

Reconnect the D5, D6 and A73 main body ECU (network gateway ECU) connectors.


e.

Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly.


f.

Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
A73-5 (CODE) - Body ground Input LG - Body ground Demodulated signal of key code data Key inserted in ignition key cylinder Pulse generation
A73-9 (IMO) - Body ground Input / output Y - Body ground EFI communication Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A73-8 (VC5) - Body ground Output R - Body ground Transponder key amplifier power supply Ignition switch ON 4.5 to 5.5 V
A73-15 (TXCT) - Body ground Input W - Body ground Key code output signal Key inserted in ignition key cylinder Pulse generation
A73-16 (AGND) - Body ground - GR - Body ground Transponder key amplifier ground Always Below 1 Ω
A73-17 (UART) - Body ground* Input / output SB - Body ground Transponder key ECU communication Key inserted in ignition key cylinder Pulse generation

*: w/ Transponder Key ECU Assembly




CHECK TRANSPONDER KEY ECU ASSEMBLY


U146914E03
3.531,0.521 3.802,0.677 0.271,0.156 10 false A64

a.

Disconnect the A64 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
A64-1 (+B) - Body ground Input L-R - Body ground Battery power supply Always 11 to 14 V
A64-5 (GND) - Body ground - B-Y - Body ground Ground Always Below 1 Ω


c.

Reconnect the A64 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
A64-3 (UART) - A64-5 (GND) Input/Output SB - B-Y Main body ECU communication Key inserted in ignition key cylinder Pulse generation



CHECK ECM


U146803E05
0.802,0.781 1.094,0.938 0.292,0.156 10 false A36 2.469,0.781 2.76,0.938 0.292,0.156 10 false A35 4.323,0.792 4.615,0.948 0.292,0.156 10 false A34 5.969,0.792 6.26,0.948 0.292,0.156 10 false A33

a.

Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition
A33-1 (+B2) - A36-4 (E01) Input V - B-L Battery power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A33-2 (BATT) - A36-4 (E01) Input W - B-L Battery power supply Always 11 to 14 V
A34-6 (+B) - A36-4 (E01) Input V - B-L Battery power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A35-25 (IMO) - A36-4 (E01) Input/Output Y - B-L Main body ECU communication Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A36-4 (E01) - Body ground - B-L - Body ground Ground Always Below 1 Ω