Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM U

LIGHTING (INT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)


U146878E03
0.385,1.198 0.583,1.354 0.198,0.156 10 false 3D 0.208,0.167 0.385,0.333 0.177,0.167 10 false *1 1.885,6.583 2.083,6.74 0.198,0.156 10 false *2 1.479,4.052 1.677,4.208 0.198,0.156 10 false 3D 3.75,1.063 3.979,1.219 0.229,0.156 10 false MB 3.5,3.24 3.729,3.396 0.229,0.156 10 false MB 6.344,1.156 6.542,1.313 0.198,0.156 10 false 3B 1.792,5.271 1.979,5.427 0.188,0.156 10 false 3B 6.344,1.802 6.531,1.958 0.188,0.156 10 false 3A 4.938,5.281 5.125,5.438 0.188,0.156 10 false 3A 0.385,1.771 0.583,1.927 0.198,0.156 10 false 3C 4.208,4.052 4.406,4.208 0.198,0.156 10 false 3C 0.396,2.385 0.583,2.542 0.188,0.156 10 false 3E 6.24,4.063 6.427,4.219 0.188,0.156 10 false 3E 3.042,6.542 3.313,6.698 0.271,0.156 10 false A73 1.115,7.49 1.385,7.646 0.271,0.156 10 false A73 3.719,6.542 3.917,6.698 0.198,0.156 10 false D5 3.594,7.49 3.792,7.646 0.198,0.156 10 false D5 4.229,6.542 4.427,6.698 0.198,0.156 10 false D6 5.906,7.49 6.104,7.646 0.198,0.156 10 false D6

Text in Illustration
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Network Gateway ECU)

a.

Disconnect the D5 main body ECU (network gateway ECU) connectors.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. Wiring Color Terminal Description Condition Specified Condition
D5-22 (ACC) - Body ground*1 W - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V

*1: w/ Entry and Start System



c.

Disconnect the 3A, 3C, 3E, A73 and D6 instrument panel junction block assembly and main body ECU (network gateway ECU) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. Wiring Color Terminal Description Condition Specified Condition
3A-15 - Body ground W - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
3A-20 - Body ground SB - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
3A-27 - Body ground G-R - Body ground Battery power supply Always 11 to 14 V
3C-19 - Body ground L-R - Body ground Battery power supply Always 11 to 14 V
3E-1 - Body ground B-R - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


e.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3A-12 - Body ground B - Body ground Ground Always Below 1 Ω
3A-13 - Body ground B - Body ground Ground Always Below 1 Ω
A73-4 (GND) - Body ground B-Y - Body ground Ground Always Below 1 Ω
D6-1 (GND) - Body ground B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


f.

Reconnect the 3A, 3C, 3E, A73 and D6 instrument panel junction block assembly and main body ECU (network gateway ECU) connectors.


g.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3A-28 - Body ground V - Body ground Front door courtesy light switch LH input*3
Front door courtesy light switch RH input*4
Front door LH open*3
Front door RH open*4
Below 1 V
Front door LH closed*3
Front door RH closed*4
11 to 14 V
3B-13 - Body ground GR - Body ground Front door courtesy light switch RH input*3
Front door courtesy light switch LH input*4
Front door RH open*3
Front door LH open*4
Below 1 V
Front door RH closed*3
Front door LH closed*4
11 to 14 V
3D-26 - Body ground SB - Body ground Luggage compartment door courtesy light switch input Luggage compartment door open Below 1 V
Luggage compartment door closed 11 to 14 V
D5-5 (FLCL) - Body ground*3
D5-5 (FRCL) - Body ground*4
SB - Body ground Front door courtesy light LH drive output*3
Front door courtesy light RH drive output*4
Ignition switch off, front door courtesy light LH off*3
Ignition switch off, front door courtesy light RH off*4
11 to 14 V
Ignition switch off, front door courtesy light LH on*3
Ignition switch off, front door courtesy light RH on*4
Below 1 V
D5-6 (FRCL) - Body ground*3
D5-6 (FLCL) - Body ground*4
B - Body ground Front door courtesy light RH drive output*3
Front door courtesy light LH drive output*4
Ignition switch off, front door courtesy light RH off*3
Ignition switch off, front door courtesy light LH off*4
11 to 14 V
Ignition switch off, front door courtesy light RH on*3
Ignition switch off, front door courtesy light LH on*4
Below 1 V
D5-7 (DOMR) - Body ground L - Body ground Illuminated entry drive output (to map light assembly) Map light switch in DOOR position and map light assembly on Below 1 V
Map light switch in DOOR position and map light assembly off 11 to 14 V
D5-28 (ILL) - Body ground*2 Y - Body ground Ignition key cylinder light drive output Ignition switch off, ignition key cylinder light off (when operated by illuminated entry system) 11 to 14 V
Ignition switch off, ignition key cylinder light on (when operated by illuminated entry system) Below 1 V
D6-11 (LSFD) - Body ground*1 W - Body ground Front door unlock detection switch LH input*3
Front door unlock detection switch RH input*4
Ignition switch off, all doors closed and front door LH locked*3
Ignition switch off, all doors closed and front door RH locked*4
Pulse generation
Front door LH unlocked*3
Front door RH unlocked*4
Below 1 V
D6-12 (LSFP) - Body ground*1 SB - Body ground Front door unlock detection switch RH input*3
Front door unlock detection switch LH input*4
Ignition switch off, all doors closed and front door RH locked*3
Ignition switch off, all doors closed and front door LH locked*4
Pulse generation
Front door RH unlocked*3
Front door LH unlocked*4
Below 1 V

*1: w/ Entry and Start System

*2: w/o Entry and Start System

*3: for LHD

*4: for RHD


If the result is not as specified, the main body ECU (network gateway ECU) or instrument panel junction block assembly may have a malfunction.



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U190181E02
1.917,0.823 2.188,0.979 0.271,0.156 10 false D48 3.313,0.823 3.583,0.979 0.271,0.156 10 false D40 4.854,0.833 5.125,0.99 0.271,0.156 10 false D41

a.

Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.



b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D41-5 (IG2) - Body ground Y - Body ground IG power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
D48-2 (+B) - D48-11 (GND) R - B +B power supply Always 9.5 to 16 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D48-11 (GND) - Body ground B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


d.

Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
D41-16 (SWIL) - D41-24 (AGND) LG - B Engine switch illumination drive output Engine switch illumination on 11 to 14 V
Engine switch illumination off Below 1 V

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.