Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter assembly.

WIRING DIAGRAM

E249057E03
0.469,0.792 1.188,0.958 0.719,0.167 10 false MAIN Fuse 2.917,1.615 3.448,1.771 0.531,0.156 10 false GAUGE 0.573,1.438 1.208,1.75 0.635,0.313 10 false IG2 Relay 2.958,0.958 3.427,1.115 0.469,0.156 10 false MPX-B 4.75,0.698 4.927,0.854 0.177,0.156 10 false 1 4.948,0.802 5.125,0.958 0.177,0.156 10 false B 4.948,1.469 5.208,1.625 0.26,0.156 10 false IG+ 4.958,2.24 5.271,2.396 0.313,0.156 10 false ES1 4.958,2.635 5.271,2.792 0.313,0.156 10 false ES2 4.75,1.354 4.927,1.51 0.177,0.156 10 false 2 4.719,2.135 4.896,2.292 0.177,0.156 10 false 20 4.708,2.552 4.885,2.708 0.177,0.156 10 false 40 4.313,3.365 6.635,3.698 2.323,0.333 10 false COMBINATION METER ASSEMBLY 4.333,3.198 4.573,3.354 0.24,0.156 10 false D7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U147036E03
2.896,1.26 2.604,1.792 true 2.604,0.5 2.896,1.042 true 0.635,1.104 0.927,1.646 true 0.823,0.51 0.531,1.052 true 1.646,0.292 1.938,0.448 0.292,0.156 10 false D7 0.073,0.052 0.365,0.208 0.292,0.156 10 false *a 2.313,1.74 2.75,1.896 0.438,0.156 10 false ES2 2.406,0.323 2.844,0.479 0.438,0.156 10 false ES1 0.896,1.656 1.333,1.813 0.438,0.156 10 false IG+ 0.823,0.344 1.26,0.5 0.438,0.156 10 false B

Disconnect the D7 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D7-1 (B) - Body ground Always 11 to 14 V
D7-2 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-20 (ES1) - Body ground Always Below 1 Ω
D7-40 (ES2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


d.

Reconnect the D7 combination meter assembly connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR